Square Direct Weld Jack - Drop Leg w/ Spring Return - Sidewind - 25-3/4" Lift - 10K
(771 reviews)
Price: $210.25
In Stock
Square Direct Weld Jack - Drop Leg w/ Spring Return - Sidewind - 25-3/4" Lift - 10K
Item # TJD-12000SP-R2NH
Our Price: $210.25
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (771)
- Q & A (0)
- Photos
etrailer Trailer Jack - TJD-12000SP-R2NH
- Car Hauler
- Enclosed Trailer
- Fifth Wheel Trailer
- Gooseneck Trailer
- Utility Trailer
- 9001 - 10000 lbs
- Sidewind Jack
- Weld-On
- Leveling Jacks
- Tongue Jacks
- 26 Inch Lift
- With Rectangle Foot
- Steel
- etrailer
Pull the side-facing plunger pin on this heavy-duty jack to release the drop leg. The durable jack screw offers increased strength. The built-in grease zerk allows effortless greasing. Sidewind crank (TJD-12000-HD) sold separately.
Features:
- Heavy-duty utility jack lets you raise and lower your trailer
- Ideal for agricultural and commercial applications
- Drop leg with spring return increases overall extension for maximum adjustability
- Plunger pin positioned to the side
- Durable 1" jack screw allows for heavy lifting
- Twin thrust bearings make extending and retracting jack easy
- Effortless greasing with built-in grease zerk
- Black painted inner and outer tubes
- Footplate minimizes sinking in soft ground
- Weld-on installation
- Handle (TJD-12000-HD) sold separately
Specs:
- Height:
- 28" Retracted
- 40-1/4" Extended
- Total lift: 25-3/4"
- Screw travel: 12-1/4"
- Drop leg travel: 13-1/2"
- Lift capacity: 10,000 lbs
- Support capacity: 12,000 lbs
- Drive pin diameter: 1"
- 3/8" Mounting hole diameter
- Outer tube width: 4"
- Inner tube width: 3-1/2"
- Footplate dimensions: 8-1/4" long x 8" wide
- Adjustment hole spacing: 3-3/8" from center of hole to center of hole
- 1-Year warranty
TJD-12000SP-R3NH Ram Square Direct Weld Jack - Drop Leg w/ Spring Return - Side Wind - 12-1/4" Screw Travel - 10K
Replaces TJD-12000SP-R2NH
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- etrailer mistake
- Arrived Damaged
- Wrong item was ordered
Customer Reviews
Square Direct Weld Jack - Drop Leg w/ Spring Return - Sidewind - 25-3/4" Lift - 10K - TJD-12000SP-R2NH
Average Customer Rating: 4.8 out of 5 stars (769 Customer Reviews)
Pull the side-facing plunger pin on this heavy-duty jack to release the drop leg. The durable jack screw offers increased strength. The built-in grease zerk allows effortless greasing. Sidewind crank (TJD-12000-HD) sold separately.by: Chris01/27/2024
The jacks seems to be holding up, i use them as downriggers for my service truck crane. Only gave 3 stars because one of the feet on the jacks came bent and etrailer offered to send me a new jack at over $[XX] shipping or some casy back. So i took the $[XX] cash back for my 300$ jack.
by: Levi01/31/2019
I got 2 of these for a landing gear set up on my bumper pull. Customer service said there is no way to reverse gear to use as landing gear so i set them both to turn in same direction. These are by far the best price ive found. Compared to a local prices i basically got 2 for the price of one. Doesnt appear to have any sacrifice in quality either. Very heavy duty. It only took a few days to get them. Customer service is great and so is the product. If you want to see more of my set up with these jacks, you can view my trailer build videos on my online video channel carvings by levi.
by: Shane 02/06/2024
Works great. Cranks much easier than the old one did before it broke.
by: David 02/20/2024
Ram Products has great import product always very good quality
by: Matthew 06/19/2023
This jack went on a customers trailer and has worked perfectly with no issues.
by: Mark 11/24/2023
Very pleased with it
by: Mark 10/30/2023
Jacks arrived on the date promised. Great response time!
by: James 10/08/2023
Good quality fast delivery works smooth ly.
by: PeteG04/15/2017
This was a replacement for a jack that had failed. Dimensionally it was as advertised. I received the jack ahead of schedule, took it out of the box and welded it in place. Jack works smoothly and now that I have a. new jack it is obvious that the old jack had been in bad shape for quiet some time. This new one is almost effortless.
by: Nolan01/27/2018
I would recommend this trailer jack works great
Nolan
1/27/2019
These trailer jacks are working great. Easy to install just follow the instructions.
by: Scott 07/21/2023
Came really fast and should work great
by: Henry o12/05/2018
Works great on are grain cleaning trailer for leveling.
Henry W.
12/7/2019
Still working great no problems with any of the jacks
by: Randal 11/26/2022
Thickness of metal at welding locations was more than expected. Works well
by: Cody 12/09/2021
Good Jack's for the money. I use a pair of them to jack up my 25 foot loaded gooseneck a few times a week.
by: Manning10/27/2022
Fantastic product I have not installed it yet but it looks like it will work fabulously and a lot cheaper so I can get around me
by: David 12/15/2021
It was installed on my inlaws trailer as the old took three men and a baby to crank. The new one from you has performed smoothly and reliably, great value.
by: Jarrell03/01/2023
Great price and great service. Could not ask for any better!
by: Rod A.06/25/2017
This trailer jack is high quality and low priced, easy to install.
by: Roger04/21/2019
The jack was delivered days before expected. It is a lot better quality than expected.
I have not installed yet, but I have great hopes. The main reason that I purchased this jack is because I can order replacement parts.
by: Gary 02/26/2020
ORDERED A PAIR OF THESE FOR MY TILT TOP TO REPLACE THE ORIGINALS.
THEY WORK GREAT AND ARE MUCH HEAVIER THAN THE 12k's THAT CAME ON IT.
FANTASTIC SERVICE!!!!
by: MO12/03/2022
It appears to be a quality jack I installed it today and it works perfectly.
by: Donald 02/02/2023
Excellent company to deal with!
by: Leonard Burger08/20/2017
Everything as it should be. Job well done by etrailer.
by: CY04/03/2017
Excellent replacement jack and fast service
by: JimM05/15/2019
works great - no issues
Vicki M.
5/18/2020
no issues at all - would purchase again
25
766
Show More Reviews
See what our Experts say about this etrailer Trailer Jack
- Availability Of A Drill Adapter For The TJD-12000SP-R2NH Square JackUnfortunately we do not offer a drill adapter for the square jack # TJD-12000SP-R2NH. The only way to raise and lower the jack will be with the manual crank handle # TJD-12000-HD. Bulldog used to make a powered drive kit that worked with these jacks, but that has not been available for quite some time.
view full answer... - Handle Needed For Sidewind etrailer Square Direct Weld 10K JackThe handle that you need for the Square Direct Weld Jack - Drop Leg w/ Spring Return part # TJD-12000SP-R2NH is part # TJD-12000-HD. This handle replaces the handle on all of the TJD-12000 Series square jacks. It comes with the bolt and hardware needed to install.
view full answer... - Replacement for Pro Series 12,000 lb Trailer Jack Needing New ScrewTo get your Diamond C dump trailer back in working condition you'll need to swap out the entire jack as that internal drive screw isn't available as a replacement. For a replacement jack I recommend going with our etrailer Trailer Jack # TJD-12000SP-R2NH along with the Handle # TJD-12000-HD because we still have replacement parts for our trailer jacks in case you end up needing them. Also, the parent company of Pro Series is in a transition phase right now so there's no guarantee this...
view full answer...
- How To Re-Assemble The RAM TJD-12000SP Trailer Jack I went ahead and reached out to RAM and they explained to me that to re-install your inner leg to your RAM jack like the Square Direct Weld Jack - Drop Leg w/ Spring Return # TJD-12000SP-R2NH, you are going to need to re-install the lower pin, replace the lower miter gear, install the gear set and spacer on cross shaft. Re-install the pin into the upper gear and shaft, and test the jack to ensure smooth operation. Finally, re-install the cap and two screws and you're all set. I have...
view full answer...
- Solution for Ram Square Direct Weld Jack that Has Broken Return SpringThe return springs in landing gear jacks are not replaceable or repairable unfortunately so if you have the # TJD-12000SP-R2NH.
view full answer... - Does Jack Drop Leg With Spring Return Require Manually Pushing the Leg DownYes, you will have to manually push the drop leg down on the # TJD-12000SP-R2NH. Once you get it to the position you want you will re-pin it to keep it in place. This also means it will automatically retract when you pull the pin out so you don't have to raise it back up with your hand or foot.
view full answer... - Replacement Landing Gear Jack for Ram Follow 12k Jack on TrailerSend me the pictures you have and I'll see if it's something we can get.
view full answer...
- Can Two Square Direct Weld Jacks 25-3/4 Lift - 10K Be Used TogetherThe Square Direct Weld Jack part # TJD-12000SP-F2 can be used in tandem. The only thing you would need to do this would be a cross shaft which would be some sort of bar that attaches the two output shafts to one another. This is assuming you want both jacks to turn at the same time and not have independent operation with two handles. We don't have any cross shafts for this but you should be able to find the parts locally as it's just a steel pipe with holes drilled to pin the pipe to the...
view full answer... - Is Specific Amount of Ground Clearance Required when Installing Direct Weld Jack # TJD-12000SP-R2NHThere isn't a specific amount of ground clearance required when installing a jack such as Square Direct Weld Jack # TJD-12000SP-R2NH. You would mount it however it is needed for your trailer. The overall height of the jack when fully retracted is 28 inches. When fully extended and the drop leg all the way out as far as it can go the height is 40-1/4 inches. Based on this information you will be able to figure out the position that will work best on your trailer.
view full answer... - Ram Square Jack Replacement Screw AssemblyWe have several replacement parts for the internals of a Ram brand square jack. The Replacement Rod and Nut # TJD-12000-RODNUT will fit the following Ram jacks: # TJD-12000SP-F2 10K Sidewind with 12-3/8 inches of travel w/handle # TJD-12000SP-R2NH 10K Sidewind with 12-1/4 inches of travel w/o handle # TJD-12000SP-R2 10K Sidewind with 12-1/4 inches of travel w/handle Some other replacement parts for these Series jacks are: # TJD-12000-GR Replacement Gear Kit # TJD-12000-BR Replacement...
view full answer...
- Replacement Parts for etrailer Square Direct Weld JackIt sounds like you're talking about the rod and nut on the # TJD-12000SP-R2NH. We have the following replacement parts available: -Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks # TJD-12000-RODNUT -Replacement Sidewind Gear Kit for etrailer and Ram Square, Direct Weld Jacks # TJD-12000-GR -Replacement Return Spring for etrailer and Ram Square, Direct Weld Jacks # TJD-12000-RSP -Replacement Bearing for etrailer and Ram Square Jacks # TJD-12000-BR -Replacement...
view full answer... - Replacement Heavy Duty Trailer Jack for a Eby Gooseneck TrailerThanks for the information and photos, Brock! For your application I recommend picking up the 10K Square Direct Weld Jack - Drop Leg w/ Spring Return # TJD-12000SP-R2NH and reusing your current handle and crosstube. This is a weld-on installation but that's pretty common when you start getting into these higher weight capacity jacks.
view full answer... - Dimensions for Replacement Square, Direct Weld Jack Inner Tube with Spring-Return Drop LegThe drop leg portion of the Replacement Square, Direct Weld Jack Inner Tube with Spring-Return Drop Leg # TJD-12000SP-FIP measured about 3" square and is about 19" tall. Please note that this part is a direct replacement for jacks # TJD-12000SP-F2, # TJD-12000SP-R2, or # TJD-12000SP-R2NH so if you don't have one of these you will likely need to do some modification for this to fit.
view full answer... - How to Replace Interior Ram Jack Rod and Nut # TJD-12000-RODNUT on 12000 Series JacksGood news! I was able to get a exploded diagram as well as a set of instructions on how to replace the rod and gears # TJD-12000-RODNUT in the # 12000 Series Ram Jacks made after 2012. I have attached them to this page for your convenience. Basically, you will not need to remove or cut the steel plate inside the top of the jack to do this. You will want to remove the cap, then the roll pin that holds the cross shaft into the leg, this will free up the smaller gear that will be removed...
view full answer...
Do you have a question about this Trailer Jack?
Info for this part was:
Updated by:
Lindsey S
Updated by:
Wilson B
Updated by:
Ronnie R
Updated by:
Hannah L
Updated by:
Mike S
Expert Research:
Michael H
Installed by:
Cole B
Written by:
Amanda M
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Peteg
4/15/2018
Works flawlessly.