How to Determine Replacement Screw & Nut For Square Weld-On Jack

Question

Question:

Trying figure out the appropriate screw and nut kit for a square weld on trailer jack... The screw on mine is 17 and 1/4 inches long

asked by: Rick

0

Expert Reply:

You'd have to know the model number of your weld on jack to find the right replacement screw and nut. For example, the only replacement we carry is the Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K # TJD-12000-RODNUT which is for TJD-12000 Series jacks.

expert reply by: Kyle S

0

Answer 1

You can certainly change your trailer tires to a narrower 205mm width as long as your wheels are 6- or 6-1/2-inches in width. These are the only size wheels that can take both 225mm and 205mm tire sizes. Please refer to the linked article on tire…

view full answer...

Answer 2

Pacific Rim is the manufacturer of the RAM jacks. You can verify the Replacement Rod and Nut #TJD-12000-RODNUT you found is the correct part by confirming your jack is 3-1/2" by 3-1/2" square and the 1" rod is 17-3/4" long. If you…

view full answer...

Answer 3

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 6

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 7

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 12

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

How to Determine Replacement Screw & Nut For Square Weld-On Jack

Product Page this Question was Asked From

Continue Researching