Timbren 1/2" Spacer for Raised Frame Vehicles
(48 reviews)
Price: $8.29
In Stock
Timbren 1/2" Spacer for Raised Frame Vehicles
Item # TA25722-90P00
Retail:$18.27
Our Price: $8.29
You Save: 55%
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (48)
- Q & A (0)
- Videos (1)
- Photos
Timbren Accessories and Parts - TA25722-90P00
- Vehicle Suspension
- Spacers
- Lift Spacers
- Timbren
1/2" Spacer fits vehicles with raised frames.
Features:
- Spacer fits vehicles with raised frames
- Thickness: 1/2"
- Quantity: 1 spacer
A25722-90P00 Timbren 1/2" Spacer for Raised Frame Vehicles
Video of Timbren 1/2" Spacer for Raised Frame Vehicles
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Timbren Vehicle Suspension TA25722-90P00 Review
Speaker 1: Today we're taking a look at a Timbren 1/2 inch Spacer for raised frame vehicles. Timbren recommends that you have a 1/2 inch to an inch of clearance between the Timbren and the contact point when the vehicle isn't under a load. If the clearance is more than what's recommended, then a spacer is the ideal solution. It installs easily and allows you to have full function of your Timbren suspension system even though you have a vehicle with a raised frame. This particular spacer measures a 1/2 inch thick. Top to bottom is 1/2 inch.
The hole here in the center will accepts 3/8 inch diameter hardware.Remember that you may need longer hardware since you're adding the spacer to your setup. You can go to your local hardware shop and pick something up. That's exactly what we do when we install these on customer vehicles here in our shop. When it comes to the overall diameter, edge to edge we're looking at four inches. With this part number you get one spacer.
I also want to mention that we do offer this in a one inch thickness with part number A25723-90AH00. You can view that right here at etrailer.com. That's gonna do it for today's look at the Timbren 1/2 inch spacer for raised frame vehicles.
Customer Satisfaction Score:
95% were satisfied with this product
5% of customers were not satisfied
- Wrong item was ordered
- Alternate product found
- Product did not meet expectations
Customer Reviews
Timbren 1/2" Spacer for Raised Frame Vehicles - TA25722-90P00
Average Customer Rating: 4.8 out of 5 stars (48 Customer Reviews)
1/2" Spacer fits vehicles with raised frames.by: DNH11/09/2023
Have had them for a year along with the Timbren SAS and have hauled a camper about 9000 miles without an issue. They really stabilize the load on my 2500. You go from white knuckling to actually enjoying the drive. Well worth it, and an easy install!
by: Liz08/15/2020
The wrong spacer was ordered and Danielle was helpful with getting that order cancelled and a the correct part sent. Unfortunately, and unbeknownst to us the part had already been picked and sent down the chute so I ended receiving both sets. But Danielle saved the day by emailing a return label, which made it a simple process to get the wrong set returned.
The Spacers themselves were pretty easy to install and closed the gap between the Timbren Spring and the axle contact point to where it will engage sooner. They, the Timbren's, were doing their job before adding the spacer but I was looking for a little less squat when the trailer is connected and by adding the spacer was able to achieve it.
by: Steve04/10/2020
They work like they are supposed to. I used them in conjunction with my timbrens to take up some gap on them. For reference to those with an at-4 GMC, I have a 2020 and with this 1/2" and the timbren (it was actually only 4 1/2" tall, not 5" like the images showed) have about 1.25" gap between the bottom of the timbren and the axle stop. I was under the impression that the timbren itself was 5" based on the image in the kit I got, tgmrck15s, so I'm a 1/2" shorter than I wanted but I will run it for a while and see how it looks when loaded with my trailer before going any thicker with a spacer.
by: Tim07/24/2019
Good product, does exactly what it is designed to do. The only words of wisdom I can pass on are to make sure it is not riding to close to the axle when your truck is empty or it will kick and have a rough ride (when empty only). This space can be adjusted by adding or removing the spacers. You can see in the picture that I have about 1.5 inches of clearance on my setup. Once the truck is loaded and they are in use they perform beautifully. Definitely helps reduce sag and supports the load evenly from side to side. 2018 F150 XLT FX4
by: Joseph 06/11/2023
Worked perfectly for my slightly lifted F150. Without, the bed would drop a bit too much before engaging the overloads wich raised the front enough to cause mild drivability issues.
by: Larry 01/29/2022
These came quickly and were very easy to install after I finally figured out what wrench was necessary to remove the factory jounce bumpers. A 10 MM socket was what it took.
by: David07/03/2021
I used the spacers after checking measurements before installation on my GMC 2021 Sierra 1500 AT4. More information in my review of the full enhancement system to follow.
by: Vic C04/18/2017
I am very happy with the performance of Timbrens on my 2014 Ford F-250. When unloaded and not needed, the Timbrens sit idle, but when I hitch up my 7000 lb trailer, the Timbrens provide additional support to the stock springs which results in better rear end stance and better handling while towing. I think it makes my F-250 more like a F-350 when towing.
Because the original Timbrens installed were about 1 and 1/2 inches from the axle, I added the 1/2 spacer, which put the Timbrens in ideal position in regard to the axle and loading.
by: AW10/21/2020
The timbrens help control sway plus providing load leveling with a heavy load.
I really like them/
Alfred
10/22/2021
Been working great, helps keep PU level when trailer is attached with out load levelers! For long haul I still use the load lever hitch though.
by: Elaine06/01/2021
Had Timbren rear suspension system installed on my F250 Super Duty. I use with a 3horse heavier blt trailer with 8ft short wall. I can't believe how much more stable the truck feels with this system. Love it and would most certainly recommend this system be added to their truck. I wish I knew years ago to add this system to my truck.
by: Wayne A.10/13/2017
Works well. At first, I had too many spacers, and it caused a harsh ride. I removed 1" of rubber and got my good, no load ride back. When I hitch up my 5th wheel toy hauler, I get a sure, stable ride, without rear end sag and front end lift.
by: Ed H10/17/2017
I have had these on many of my trucks, great product, better than air bags for me. I put these on a 2013 F-150 that pulls a 5000 pound boat. Easy installation and nice ride. Keeps my headlights aimed properly, no sag. Highly recommend.
by: Davey02/20/2019
Product works great! Installed these on a 2018 Ford F150 that has a leveling kit. I didn't want the truck to sit below level in the rear when towing my trailer. I tried the Timben without these initially, and then purchased these to maintain the ride height I was looking for. Well worth the money.
by: Andrew 03/05/2021
Perfect fit and dialed in the clearance just the way I wanted it. I preferred to have my Timbrens on the closer side of what they suggested. I do wish they came with a longer bolt though for convenience sake. Fortunately, on the 2020 Silverado 1500's I didn't need the locknut at all, the hole is threaded. A little red lock tight for a little added security and I was done. They are holding great.
by: Quint W.10/10/2017
The spacers are great. I had previously installed the TORTUN4 Timbrens, but with a 6" lift the truck still sat too low in the rear when loaded. The spacers allowed the timbrens to come into affect much sooner and prevent rear end sag. Didn't know spacers were an option until I found them on etrailer. Thanks for an awesome website!
by: John05/14/2022
I placed these on my farm truck and they absolutely did the trick. I haul hay trailers and cattle trailers and the difference these made over the OEM bump stops is remarkable.
by: Rich G10/17/2016
I put these on a 2007 Tundra and this past summer it pulled work& play toy hauler from Pa. To Yellowstone and back with no issues. The truck handled the weight great.
by: Roadhog09/20/2021
Just what I needed to reduce the gap between my Timbren helper springs and the bump stops.
by: Todd W.07/09/2017
Love my Timbrens and been using them for years. These 1/2 spacers are handy to help dial in perfect ride height.
by: Thomas W09/11/2018
The guys at e-trailer and Timbren are great. Needed 1/2” spacers for my Tundra for my timbren overloads and they had them to me in 2 days. They fit and work great. Exactly what I needed. Thanks.
by: Russell07/22/2018
Etrailer has nothing but great products and this was no exception exactly what I needed
by: Glenn 01/23/2023
Did exactly what I wanted it too. It did require trimming and then sanding to match the top piece. It was a breeze and not too difficult.
by: Ric 06/09/2021
Well made part. I actually need these instead of the ones that came with the Timbren kit, (TRF150D)
Ric
6/10/2022
Moved from WA to central UT, made numerous trips pulling an 18 car hauler. The Timbrens kept everything level and firm. Love those things!
by: Rich S12/08/2016
Needed product quickly and dependably to complete a customers truck in a timely fashion. E trailer came through as promised w the correct product and delivered on time.
by: Matt04/05/2019
Got the spacers I needed in two days
Thank you etrailer!
25
48
Show More Reviews
See what our Experts say about this Timbren Accessories and Parts
- Recommended Timbrens for 2003 GMC Sierra 1500 with Add-A-LeafIn regards to the Timbren Rear Suspension Enhancement System for a 2003 GMC Sierra 1500 LD part # TGMRCK15S for extended or regular cab models and part # TGMRCK25S for crew cab models, the space between the frame and axle if extended can be compensated for using spacers to fill the gap which is common in lifted applications. For this, you'd just need to use a combination of the Timbren Spacers part # TA25722-90P00 for 1/2" or part # A25723-90AH00 for 1" until you get between 1-1/2" - 1"...
view full answer... - How to Determine If a Spacer is Needed When Installing Timbren Springs on 2022 Ford F-350If you're wanting to install the Timbren # TFR350SDJ on your 2022 Ford F-350 then you'll want to measure the distance from where your factory bump stops are installed down to the point of contact on the axle. The Timbren # TFR350SDJ are 7-1/2" tall and according to the manufacturer you need to have 1/2" to 1-1/2" of a gap between the rubber spring and the contact point. If you measure from the place where your OEM bump stop sits down 7-1/2" and the gap that is left is between the 1/2" to...
view full answer...
- Recommended Front Suspension Enhancement On 2009 Ram 2500 CumminsIf you have a working front suspension, the Timbren Front Suspension Enhancement System # TDDF974A shouldn't raise your front end but just keep it from bottoming out. It isn't intended to change the empty ride of your vehicle, but to engage as the factory suspension needs the additional support. They do act like shock absorbers getting more rigid as they compress to support the load. If you want to engage the spring sooner you can add a spacer if needed in 1 inch increments using # A25723-90AH00...
view full answer... - How To Prevent Sag While Towing/Hauling with a Lifted 2005 Chevrolet AvalancheI do have an option for you but there would be no way to confirm fitment of the Air Lift AirLift 1000 Air Helper Springs part # AL60769 on your 2005 Chevrolet Avalanche with aftermarket coil springs. The Air Lift AirLift 1000 Air Helper Springs are designed to work with factory rear coil springs only therefore I recommend taking a look at the Timbren Rear Suspension Enhancement System part # TGMRG25C which like the Air Lift AirLift 1000 Air Helper Springs will also work to help reduce sag...
view full answer... - Heavy Duty Timbren Kit Recommendation for a 2012 Ram 3500 with 4-1/2 inch LiftYes, but you will also need four of the 1 inch spacers part # A25723-90AH00 and one of the 1/2 inch spacer part # TA25722-90P00 per side of your truck to install the Timbren kit part # T94VR.
view full answer... - Are Spacers Needed for Timbrens on 2021 Chevrolet Silverado 1500 Z71 Trail BossYes, the Timbren Suspension Enhancement System # T28MR will be the best option when it comes to cost-effectiveness. This will fit with your 2021 Chevrolet Silverado 1500 Z71 Trail Boss but you'll want to make sure these fit the gap properly. The Timbrens measure 5-5/8" high overall and you need a gap of 1/2" to 1-1/2" for the Timbrens to be effective. If you find that you have more than 1-1/2" of a gap then you can use the 1/2" Spacer # TA25722-90P00 and the 1" Spacer # A25723-90AH00 as...
view full answer... - Recommended Spacers For Timbren Front Suspension System for Leveling Kit on 2011 Silverado 1500For as many inches or half inches you add to the front of your 2011 Silverado 1500, I recommend using the appropriate spacers since you will be using a snowplow. I recommend the Timbren 1" Spacer For Raised Frame Vehicles # A25723-90AH00 or the 1/2" Spacer for Raised Frame Vehicles # TA25722-90P00. This will require longer hardware that will need to be obtained locally.
view full answer... - Recommended Timbren Rear Suspension Enhancement for Ford Super Duty TruckThe Timbren Rear Suspension Enhancement System # TFR250SDG is the part number you are looking for and is compatible with 2011-2014 Ford F-250 and F-350 models as well as 2015-2016 Ford F-250 models. This kit comes with the proper brackets and hardware needed. The price will be listed in the product description below. Let me know if you have any further questions.
view full answer... - Does 2020 Ford F-350 with Leveling Kit Need Spacers When Installing Timbren Suspension KitTypically a leveling kit for the suspension of a truck like your 2020 Ford F-350 is a slight lift to the front suspension so that the front and rear of the truck is leveled. Higher rated trucks like yours have the rear suspension sitting up quite a bit taller since the suspension is beefed up more back there to compensate for the weight of cargo or a trailer. So with a Timbren kit like the # TFR350SDJ that fits your truck installed you wouldn't need any spacers as long as only the front...
view full answer... - Spacers to Use for Timbren Kit on 2009 Ford Ranger to Take Up 1-1/2 inch of SpaceTo get a total of 1-1/2 inch of spacer for your Timbren kit part # TFRR050A you'd need to use the 1 inch spacer part # A25723-90AH00 as well as a 1/2 inch spacer part # TA25722-90P00.
view full answer... - Jounce Bumper Spring versus Air Springs on a lifted 2008 Ford F-250For your 2008 Ford F-250, I can help you with enhancing your factory suspension. You are correct in saying that the air bags have more flexibility, but do require more maintenance than the jounce spring systems which are maintenance free. Either option will work with your lifted truck, but if you are primarily concerned about suspension support when towing your 5th wheel, then the jounce replacement springs are an excellent low cost option. For your needs, I'd suggest the Timbren Rear...
view full answer... - What Spacers Can Be Used With The Timbren Rear Suspension Enhancement System?Yes, the Timbren Rear Suspension Enhancement System # TGMRYS4 is compatible with the Timbren 1" Spacer For Raised Frame Vehicles # A25723-90AH00 and the Timbren 1/2" Spacer for Raised Frame Vehicles # TA25722-90P00. You will need to supply the hardware, as the hardware that is included won't work with the spacers installed. The hardware included is 3/8 x 1-1/2 inch UNF Grade 5 bolts, so you will want to stick to the same grade and diameter, but will need a longer length.
view full answer... - Timbren Suspension Enhancement System for 2012 Chevy Silverado 1500 With 6 Inch LiftLike you mentioned, you will need spacers, but your 2012 Chevy Silverado 1500 with a 6 inch lift is compatible with the Timbren Rear Suspension Enhancement System # TGMRCK15S. Since there should be between 1/2" and 1-1/2" of space between the bottom of the Timbren spring and contact point, five on each side of the Timbren 1" Spacer For Raised Frame Vehicles # A25723-90AH00. If you install them and there is a bit of a larger gap, you can always add another spacer, either the 1" or the...
view full answer... - Can You Use Spacers With Service Duty Timbrens On a 2022 Ford F-350Yes, you can add spacers to the Timbren Suspension Enhancement System part # TFRTT350J which is the service duty model designed for a 2022 Ford F-350. The correct spacer will be the Timbren Spacer part # A25723-90AH00 for 1" or part # TA25722-90P00 for 1/2".
view full answer... - Troubleshooting Front End Sway Of A 2022 Entegra Odyssey 25R Class C Motorhome With SumoSpringsA half inch gap between your SumoSprings # SSF-106-47 and the front axle is well within the normal range. The SumoSprings you installed are on the softer side of the spectrum so if you're experiencing a lot of sway you would actually want to go on the heavier side with the Timbren Front Suspension Enhancement System # TUMDF70. These Timbren springs have a combined 5,600-lb capacity and are much stiffer than the SumoSprings which will only reach their max capacity of 500lbs each when they...
view full answer... - Recommended Timbren Spacer Needed for a 2012 Ford F-250The recommended space between the bottom of the Timbren Rear Suspension Enhancement System part # TFR250SDG and the contact point on your 2012 Ford F-250 when unloaded is around 1/2" to 1-1/2". The Timbrens are designed to work with all factory features including the 20" tires. However, once you install the springs and determine that you have more than the recommended space, you can install multiple of either the Timbren 1" Spacer part # A25723-90AH00 or the Timbren 1/2" Spacer part # TA25722-90P00...
view full answer... - Recommended Timbren Rear Suspension Enhancement System for a Lifted 2011 Ford F-150The Timbren Rear Suspension Enhancement System part # TFR1504D is for 4 wheel drive models, part # TFR1502D is for 2 wheel drive models, and part # TFR1504D-P3 is for 4 wheel drive models that have been lifted 4". The weight capacities are different for the 4 wheel and 2 wheel drives models because 4 wheel drive models are heavier and require stiffer springs than 2 wheel drive models. For your 2011 Ford F-150, I recommend using part # TFR1502D if your truck is 2 wheel drive or part # TFR1504D...
view full answer... - Rear Suspension Enhancement for a Lifted 2014 Ford F-250 with B&W Gooseneck HitchI do have a similar rear suspension enhancement option for you but the Firestone Ride-Rite Air Helper Springs part # F2597 are not compatible with the B&W Turnoverball Underbed Gooseneck Trailer Hitch part # BWGNRK1111 on your 2014 Ford F-250 as the gooseneck hitches frame brackets block the bolt hole needed to attach the upper airbag brackets. Unfortunately, none of the airbag kits we have for your vehicle will work with lifted applications. On the newer Ford F-150's and F-250's, there...
view full answer... - Do I Need Spacers To Install Timbren Springs On 2020 Ford F-350 Super Duty With LiftTo install the Timbren Suspension Enhancement System - Rear Axle part # TFR350SDJ on the 2020 Ford F-350 Super duty you will need spacers to make up the space from the lift. Timbren recommends having 1/2" to 1-1/2" of gap between the spring and the contact point. Measure from the spot where the OEM bump stop is installed down 7-1/2". The Timbren spring will be 7-1/2" long once installed. If you have more than a 1/2" space between that measurement and the contact point you will need a spacer. Depending...
view full answer...
- What Spacer Bushing Diameter is Used with Timbren Kit that Fits 2022 Chevy Silverado 2500The Timbren kit part # TGMRCK25D that fits your 2022 Chevy Silverado 2500 would require the lift spacers that have a 3/8 inch diameter bushing hole like the part # A25723-90AH00 which is 1 inch thick or the # TA25722-90P00 for a 1/2 inch diameter spacer.
view full answer... - Are Spacers Needed For Timbren Suspension Enhancement on 2022 Ram 2500 Power WagonIf you're saying the space where the Timbren would install is 7" you wouldn't need a spacer. About an inch gap is what is recommended, and the Timbren # TDR2500D for your truck measures 5-3/4" in overall height. A 1" spacer is included which would make it 6-3/4". We do have the spacers though, the # TA25722-90P00 is the 1/2" and the # A25723-90AH00 is the 1". I would go ahead and measure to be sure. If it is 7" you could leave the spacer off or if you want them to engage sooner add a...
view full answer... - How Much Distance is Ideal between Vehicle Frame and Timbren SpringTimbren likes to recommend 1 inch between the axle and the Timbren when the truck is unloaded. We have found that this works the best. This allows the suspension to feel when the vehicle is unloaded and still gives you support when needed when towing. Since you have 1-1/2 inches currently you'd want to use the 1/2 inch spacer part # TA25722-90P00 to give you the ideal support/ride quality. Then for a the front axle you'd want the part # TGMFK25D which is confirmed as a fit as well.
view full answer... - Suspension Enhancement to Reduce Sag on Lifted 2018 Ford F-150 When TowingThe best way to fix the sag you are getting on your lifted 2018 Ford F-150 when towing a trailer is to use the Timbren Rear Suspension Enhancement System # TFR1504E which is designed for this exact situation - reduce the amount of sag on a truck when it is towing. The Timbrens will get more rigid with the more weight put on them and ensure your '18 F-150 does not sag as you tow. The issue is that you have a 6" lift, and assuming it is a suspension lift (and not a body lift) you can add...
view full answer... - Can Timbren Suspension Enhancement Fit 2016 Ram 1500 with Lift KitYes, Timbren does offer spacers that allow a lifted truck like your 2016 Ram 1500 use a Timbren kit like the # TDR1500DQ and still have the correct amount of distance between the frame and the Timbren spring. For a 1 inch spacer you'd need the part # A25723-90AH00 and then for a 1/2 inch spacer you'd need the part # TA25722-90P00. The spacers are sold individually so you'd need to order a quantity that matches the space you need to take up for each side of the axle. So if the distance...
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Expert Research:
Jameson C
Expert Research:
Jeffrey L
Written by:
Laura H
Installed by:
Cole B
Updated by:
Wilson B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Larry
1/30/2023
They help keep my Denali 1500 from sagging so much when I tow my car hauler with the car in it.