What Spacer Bushing Diameter is Used with Timbren Kit that Fits 2022 Chevy Silverado 2500

Question

Question:

I’m looking at Timbren spring bump stop, with spacers. However spacers come with multiple bushing sizes. I have 2022 Silverado 2500. What size bushings are on the rear set?

asked by: Mark P

1

Helpful Expert Reply:

The Timbren kit part # TGMRCK25D that fits your 2022 Chevy Silverado 2500 would require the lift spacers that have a 3/8 inch diameter bushing hole like the part # A25723-90AH00 which is 1 inch thick or the # TA25722-90P00 for a 1/2 inch diameter spacer.

expert reply by: Jameson C

1

Answer 1

While the spacers included in the Kit #T68MR will work with your Timbren Springs #TGMRYS4 they do not use the same mounting bolts. Your GMC Yukon uses 3/8" hardware while the spacer kit includes M10 hardware so you would still need to source the…

view full answer...

Answer 2

Yes, the Timbren Rear Suspension Enhancement System #TGMRCK35S can still be used on your 2007 Chevy Silverado even though its been lifted. You'll just need to install a spacer to get the gap between the Timbren and the axle around 1" to…

view full answer...

Answer 3

I do have an option for you but SuperSprings does not offer any additional spacers for the SumoSprings Trailer Helper Springs part #SS26MV. That said, we do still have spacers that will work for this, the Timbren Spacer part #A25723-90AH00 for…

view full answer...

Answer 4

The Timbren Spacer Kit item #T68MR has two 1/2" Spacers and two 1" Spacers which all have a 3/8" bolt hole opening. Also included are 3 pairs of different length bolts to ensure you have the correct length.

view full answer...

Answer 5

The Timbren Active Off-Road Bumpstops part #TABSOSR which are a fit for a 2007 Toyota Tacoma are designed so that there is more space between the spring and frame to allow the suspension to articulate freely when off-road. If you're looking for a…

view full answer...

Answer 6

I spoke with my contact at Super Springs and the SumoSprings Custom Helper Springs, #SSR-204-40, will fit on your 2003 GMC Yukon XL with coil springs as long as it is a 1500 model. These springs are designed to replace your factory bump stops. Once…

view full answer...

Answer 7

Welcome back! The Timbren Spacer Kit item #T68MR is exactly what you need. They have a 3/8" bolt hole opening that will work with the Timbren item #TGMRCK25D you purchased awhile ago. Timbren recommends a 1" gap between the jounce spring…

view full answer...

Answer 8

To add a 1" spacer #A25723-90AH00 to the Timbren Active Off-Road Bumpstops #TABSOSR you were looking at for your 2014 Toyota Tundra you will need to purchase two grade 5 or 8 3/8" x 2-1/2" F/T UNC bolts from your local hardware store.…

view full answer...

Answer 9

There is only one option to replace a Lippert, which is now Curt, Turning Point. You will want the Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box item #GY48GR. As far as make and model goes. 5th wheel trailer pin boxes are not model…

view full answer...

Answer 10

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...