Do I Need Spacers To Install Timbren Springs On 2020 Ford F-350 Super Duty With Lift

Question

Question:

I am thinking about putting the timbrens do i need a spacer ? its a 2020 ford f150 f-350 with a 1-1/2 lift

asked by: Mark

0

Expert Reply:

To install the Timbren Suspension Enhancement System - Rear Axle part # TFR350SDJ on the 2020 Ford F-350 Super duty you will need spacers to make up the space from the lift. Timbren recommends having 1/2" to 1-1/2" of gap between the spring and the contact point. Measure from the spot where the OEM bump stop is installed down 7-1/2". The Timbren spring will be 7-1/2" long once installed. If you have more than a 1/2" space between that measurement and the contact point you will need a spacer.

Depending on how much space is left you will need a 1/2" spacer part # TA25722-90P00 or a 1" spacer part # A25723-90AH00. If you do need a spacer you will need to source longer grade 8 M10 bolts elsewhere to install the spacers.

expert reply by: Heather A

0

click to enlarge

Answer 1

There is not a specific lifespan for a weight distribution system. If maintained and the system is properly rated for your towing setup, it can potentially last for a long time. When determining if it should be replaced, you will just want to take…

view full answer...

Answer 2

The Timbren Trailer Suspension Enhancement System for Underslung Axles #T92MR is 5-1/4" tall. Timbren recommends The spring be in constant contact with the frame at all times. So ideally you will want exactly 5-1/4" from your axle…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 6

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 7

There's not many differences between the Air Lift WirelessONE item #AL25980EZ and item #AL25980. The main difference is that the item #AL25980EZ has a slightly higher CFM at 1.03 compared to 0.92 and it runs slightly more efficient at 9% over 15%…

view full answer...

Answer 8

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

I recommend going with the Air Lift LoadLifter 7500 XL Ultimate Air Helper Springs #AL89DQ for hauling around an in-bed camper with your 2024 Ford F-350 Super Duty. I really like this kit because it has the higher 7,500 lb rating (which you don't…

view full answer...

Answer 11

The best air bag kit for your 2020 Ford F-250 Super Duty with a single rear wheel are the Firestone Ride-Rite Air Helper Springs because they are the strongest, most durable air bags on the market to provide you with optimal support for your…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Do I Need Spacers To Install Timbren Springs On 2020 Ford F-350 Super Duty With Lift

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching