Extended Round U-Bolt Kit for Roadmaster Anti-Sway Bars

See what our Experts say about this Roadmaster Accessories and Parts

• Recommended Sway Control and Ride Suspension for 2004 Gulfstream Independence with Ford f-550 Frame
  For your 2004 Ford F-550 motorhome chassis, the Roadmaster Rear Anti-Sway Bar # RM-1139-143 is the correct fit for your motorhome if it is up to 34 feet long. It if it longer, then you will instead use # 1139-144. The rear anti-sway is the most help out of all components. You will likely need longer u-bolts # RM-590050-00 or # RM-590050-10. Next, the Front Anti-Sway Bar # RM-1139-148 is the next best step followed by the Roadmaster Reflex Steering Stabilizer with Mounting Brackets for...
  view full answer...
• Recommended Suspension Enhancement For a 1996 Fleetwood Bounder 28T on Ford F-53 Chassis V8 Engine
  For your 1996 Fleetwood Bounder 28T of the Ford F-53 chassis with the V8 I recommend the Roadmaster Rear Anti-Sway Bar # RM-1139-143. This will add a sway bar to the rear of your suspension to reduce sway and provide better stability when turning. First you will want to check your U-Bolts on your rear axle to determine if they are going to be long enough to allow for the sway bar. A 1/2" thick plate will need to be added to the U-bolts. We have the Square Extended U-Bolt Kit # RM-590050-00...
  view full answer...
• Anti-Sway Bars for 2019 Tiffin Allegro Open Road Motorhome
  According to what I was able to find, the 2019 Tiffin Open Road Allegro is manufactured on a Ford F-53 Chassis. The exact sway bar you need will depend on the GVWR of your motorhome, which should be mentioned on the manufacturer's ID plate along with the VIN and other important information. For 15,700 lb, 18,000 GVWR models less than 34 feet long, use # RM-1139-146 which would install in conjunction with the existing sway bar. For 22,000, 24,000 or 26,000 lbs, use # RM-1139-149. The factory...
  view full answer...
• Recommended Suspension Steering and Anti-Sway Components for 2020 Ford F-53 Chassis
  My recommendation for increasing the stability of the 2020 Ford F-53 chassis is to replace the factory installed sway bars and adding a steering stabilzer. - Front Anti-Sway bar, # RM-1139-148 - Rear anti-sway bar, # RM-1139-149 - Steering Stabilizer, # RM-RBK25-RSSA You may or may not need # RM-590050-00 for square U-bolts or Round U-Bolt Kit, # RM-590050-10. - Rear Axle, SumoSprings Maxim Custom Helper Springs, # SSR-187-54-1 - Front Axle, SumoSprings Rebel Custom Helper Springs, #...
  view full answer...
• Suspension Enhancement Recommendations For A 2002 Thor Hurricane Class A Motorhome
  For the front you can use the Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Class A Motor Homes # RM-RBK22-RSSA to help keep your 2002 Thor Hurricane Class A Motorhome in line. For the rear if your RV is 34' or more you'll need the Roadmaster Rear Anti-Sway Bar Item # 1139-144. If your RV is 33' or less then you'll need the Roadmaster Rear Anti-Sway Bar Item # RM-1139-143. Note: These kits use a flat plate that is held in place by the leaf spring U-bolts on the rear...
  view full answer...
• Anti-Sway Bars for a 2008 Thor Hurricane 34Y w/ Garage
  For your 2008 Thor Hurricane 34Y with garage you can use the below anit-sway bars: Front - Roadmaster Front Anti-Sway Bar # RM-1139-148 Rear - Roadmaster Rear Anti-Sway Bar # RM-1139-149 This kit uses a flat plate that is held in place by the leaf spring U-bolts on the rear axle. Check to ensure there is enough exposed U-bolt below the nut to accommodate the factory nut and washer once the 1/2-inch thick plate is installed above them. If you do not have enough exposed U-bolt, order one...
  view full answer...
• Recommended Anti-Sway Bars for 2005 Fleetwood Bounder 34F
  For your 2005 Fleetwood Bounder 34F, I recommend replacing the rear sway bar first. The rear needs more stability than the front based on the axle placement and weight so it will make the greater impact. I recommend the Roadmaster Rear Anti-Sway Bar # 1139-144. This retains the factory sway bar. The factory u-bolt may not be long enough for the factory nut, washer and 1/2" plate. If not, square top u-bolts will need # RM-590050-00, and round top u-bolts will need # RM-590050-10. To...
  view full answer...
• Recommended Sway Bars For a 2011 Tiffin Allegro RV Motorhome On a Ford F-53 22,000LB Chassis
  I recommend the Roadmaster Front Anti-Sway Bar # RM-1139-148 for the front of your 2011 Tiffin Allegro on the Ford F-53 22,000lb chassis. This will replace your current way bar with a thicker and stronger 1-3/4" sway bar and uses polyurethane bushings versus rubber. For the rear the Roadmaster Rear Anti-Sway Bar # RM25VR will add a 2nd sway bar to the rear of your chassis. This bar is also 1-3/4" in diameter like the front with polyurethane bushings. You will need to measure the the amount...
  view full answer...
• Recommended Suspension Enhancement For a 2020 Winnebago Adventurer 36Z Leaning Due to Weight
  Using the SumoSprings Maxim Custom Helper Springs # SSR-180-54-1 will greatly reduce the amount your 2020 Winnebago Adventurer 36Z leans to the passenger side. You will want to install these on both sides otherwise you will have very different steering characteristics when driving. To drastically improve the overall suspension and drivers experience you will also want to add the Front SumoSprings # SSF-170-40-2, Front Sway Bar # RM-1139-148, Rear Sway Bar # RM-1139-149 and Steering Stabilizer...
  view full answer...
• Rear Sway Bar for 2005 Fleetwood Fiesta
  Since your GVWR is 20,500 lbs and you're less than 34' long the best option is the Roadmaster Rear Anti-Sway Bar # RM-1139-143 you were looking at. Your factory U-bolts will need to be long enough to account for the extra 1/2" of thickness and still have at least 3 threads exposed past the nut when properly installed. Measure your current U-bolts to see how much it extends past the nut to determine if they will work or not. If they are too short, you will also need the Extended Round U-Bolt...
  view full answer...
• Recommended Anti-Sway Bar for 2006 Fleetwood Bounder Gas Engine on Ford F53 Chassis
  I did a little bit of research and it looks like 2006 Fleetwood Bounder with a gas engine was built on a Ford F53 chassis like you mentioned, so the correct rear anti-sway bar for your rig with a GVWR of 20,500-lbs is the Roadmaster # RM-1139-143. It should be noted that the factory u-bolt may not be long enough for the factory nut, washer and 1/2" plate when used with this bar. If that is the case, if you have square top u-bolts will need # RM-590050-00, and if you have round top u-bolts...
  view full answer...
• Recommended Suspension Upgrades for a 2018 Jayco Precept 36T
  The first and most important suspension upgrade you will want to make on your 2018 Jayco Precept 36T is an upgraded rear anti-sway bar, the Roadmaster Rear Anti-Sway Bar part # RM-1139-149. The Roadmaster Rear Anti-Sway Bar is going to help minimize the floating/rocking feeling while out on the highway which is typically the most common complaint with a motorhome and the weakest component from the factory. The second most important suspension upgrade you will want to make is a set of...
  view full answer...
• Sway Bars and Steering Stabilizer For With a 2023 Fleetwood Flair 29M On Ford F53 V8 18,000LB GVWR
  As your 2023 Fleetwood Flair is on a Ford F53 V8 18,000LB GVWR chassis you have 2 choices for the rear sway bar. The Roadmaster Rear Anti-Sway Bar # RM-1139-149 is 1-5/8" in diameter and mounts in addition to the factory sway bar. They also offer the 1-3/4" Rear Sway Bar # RM25VR. This will also mount in addition to the factory sway bar but is slightly stronger being larger in diameter than the 1-5/8" sway bar. You may need the Extended Square # RM-590050-00 or Round # RM-590050-10 U-Bolts...
  view full answer...
• Is the Extended Round U-Bolt Kit Needed when Installing the Rear Anti-Sway Bar on a 2015 Ford F53
  When installing the Roadmaster Front Anti-Sway Bar for Motor Homes # RM-1139-148 and the Roadmaster Rear Anti-Sway Bar for Motor Homes # RM-1139-149 on your 2015 Newmar Canyon Star Toy Hauler there are a few things you will want to look for. When I spoke with my contact at Roadmaster he said that you will want to make sure that you have at least 3 threads showing on the U-bolts after installing the rear anti-sway bar. Since you only have half an inch that you can see you will want to go...
  view full answer...
  
• Recommended Sway Bar For 2019 Thor Motor Coach Challenger 37FH On Ford F-53 Chassis 24,000 GWR
  I recommend Roadmaster Rear Anti-Sway Bar part # RM-1139-149 and the front Roadmaster Front Anti-Sway Bar part # RM-1139-148 for the 2019 Thor Motor Coach Challenger 37FH On Ford F-53 Chassis 24,000 GWR. The factory anti-sway bars are not as thick as these after market bars so they do a better job at improving the drive-ability and reducing the sway by balancing the weight. I have attached an installation video of the bars for your reference. I do recommend to check to ensure there is...
  view full answer...
• Sway Bars and Suspension Enhancement For a 2018 Holiday Rambler Vacationer XE 32A
  According to Holiday Rambler your 2018 Vacationer XE 32A is either going to be on a 2017 or 2018 Ford F-53 chassis with a GVWR of 22,000lbs. You can confirm that this information is correct with the chassis tag posted on the wall next to your drivers seat. The Roadmaster Front Anti-Sway Bar # RM-1139-148 will replace your factory sway bar. This bar is constructed of thick 4140 chromoly steel for superior strength and uses polyurethane bushings for increased stability over traditional...
  view full answer...
• Sway Bars and Suspension Enhancement For a 2018 Thor Miramar 37.1 Motorhome
  Yes, the Roadmaster Rear Anti-Sway Bar # RM25VR will fit your 2018 Thor Miramar 37.1 on the Ford F-53 24K chassis V10 engine. You will need to measure the length of the U-Bolt threads sticking past your current plates to ensure they are long enough for the Roadmaster 1/2" plates being installed. If they are not long enough you will need either the Square # RM-590050-00 or Round # RM-590050-10 U-Bolt Kit. The Roadmaster Front Anti-Sway Bar # RM-1139-148 is the front sway bar for your Miramar....
  view full answer...
• Are Extended U-Bolts Needed To Install the Roadmaster Rear Sway Bar On a 2018 Jayco Precept 36T
  The Extended U-Bolt Kit part # RM-590050-00 (square) or part # RM-590050-10 (round) may be needed to install the Roadmaster Rear Anti-Sway Bar part # RM-1139-149 on your 2018 Jayco Precept 36T but I cannot give you a yes or no answer. The only way to know for sure would be to crawl under the motorhome and take a look at the factory u-bolts to ensure there is enough threads left to install an additional 1/2" plate.
  view full answer...
• Recommended Rear Anti-Sway Bar For 2005 Fleetwood Southwind 32V Built On Ford F-53 Chassis
  Since your 2005 Fleetwood Southwind 32V is built on the Ford F-53 Chassis and is under 34' long you will need the Roadmaster Rear Anti-Sway Bar # RM-1139-143. It is possible that your factory U-bolts will not be long enough, if they are not you will need the # RM-590050-10 if you have round U-bolts or # RM-590050-00 if you have square U-bolts. You may also be interested in the Front Anti-Sway Bar # RM-1139-148, and Steering Stabilizer # RM33RR to complete your suspension enhancement and...
  view full answer...
• Rear Anti-Sway Bar and U-Bolt Replacement Kit Installation on a 2017 Canyon Star on F-53 Chassis
  The rear anti-sway bar # RM-1139-149 will fit the V10 Ford F-53 chassis if the gross vehicle weight rating is 22K, 24K, or 26K. Based on your description you will need # RM-590050-00 u-bolt replacement kit. I have included a link to a video showing an example installation for you. It is a good idea to lift the RV and then use jack stands to support just the axle. With the vehicle supported elsewhere and the axle supported by jack stands it is less likely for the vehicle to "slip" off the...
  view full answer...
• How to Determine If Longer U-Bolt Kit is Needed for Roadmaster RM-1139-149 Anti-Sway Bar Kit
  You can easily determine if you'll need the # RM-590050-10 Extended U-bolt kit by taking a quick measurement. Measure the length of the existing U-bolt that extends through the factory nut. If you can add a 1/2 inch to account for the thickness of the plate used to attach the new anti-sway bar and have 3 threads remaining, you won't need the kit. Otherwise, you will. Since you currently have a 1/2 inch of thread exposed, I'm afraid you're going to come up short on the U-bolt length and...
  view full answer...
• How To Increase Stability and Reduce Sway Of 2020 Bounder Motorhome on 2019 Ford F-53 Chassis
  It sounds like you meant that the Fleetwood Bounder is on a 2019 Ford F-53 chassis which is very common. The first step in increasing the stability of the 2020 Fleetwood Bounder on the 2019 Ford F-53 chassis is to replace the factory sway bars. The factory sway bars, especially on the Ford Chassis are not as good as the aftermarket sway bars at keeping the motor home in line. I recommend Roadmaster Front Anti-Sway bar part # RM-1139-148 and Rear anti-sway bar part # RM-1139-149. Before...
  view full answer...
• How to Determine if Longer U-Bolts are Needed When Upgrading Anti-Sway Bar for 2015 Vista 27N
  To determine whether or not a longer U-Bolt kit is needed when you install the Roadmaster Rear Anti-Sway Bar # RM-1139-146 on your 2015 Winnebago Vista 27N Motorhome you need to look at your current U-Bolts and take a measurement. The bracket that comes with the anti-sway bar kit is 1/2" thick so you just have to make sure that you have 1/2" of extra space on your current U-Bolts plus room to have 3 threads left over. If you have enough room then you don't need the longer U-Bolts. If you...
  view full answer...
• Tools Needed to Install Roadmaster Rear Anti-Sway Bar # RM-1139-149
  The installation manual for the Roadmaster Rear Anti-Sway Bar # RM-1139-149 along with the Extended U-Bolt Kit # RM-590050-10 simply calls for a torque wrench and "general hand tools". When we installed this kit on the 2017 Ford F-53 we used a 13/16 inch socket, a 5/16 inch socket, a 15/16 inch wrench/socket, an 18mm wrench/socket, and a 16mm socket. I have attached this installation video below that you can also check out.
  view full answer...

Do you have a question about this Accessories and Part?