Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2" Receiver - 44" Wide

See what our Experts say about this CURT Heavy Duty Receiver Hitch

• Options for Front Mount Hitch 1987 E-350
  etrailer does not have a confirmed custom fit front mount hitch for a 1987 E-350 listed; I checked with our suppliers, they do not manufacture a front mount for this specific vehicle. I suggest consideration of one of the universal mount hitches such as Curt Adjustable Trailer Hitch Receiver - 18"-51" Wide - 2" Drop - Class III - 2", # C13701. Or the Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2" Receiver - 44" Wide, # C47CR. Either of these options may require additional fabrication...
  view full answer...
• Trailer Hitch Receiver Option For 2007 Ford Collins E450
  There isn't a custom fit hitch for your 2007 Ford Collins E450, so you'll need a weld-on hitch, with the right one depending on the drop you need, as well as your frame width. If the width of your frame is 44 inches or less (from outside to outside), you can use one of the following: - 3" Drop: Class V Universal Weld-on Receiver Hitch and Brackets # 15901 - 9" Drop: Class V Universal Weld-on Receiver Hitch and Brackets # C47CR For the drop, what you'll want to do is measure straight...
  view full answer...
• Front Mounted Trailer Hitch Options For A 2024 Jeep Wagoneer
  Hi Stephen, There isn't a custom-fit front hitch available but we do offer adjustable-fit weld-on trailer hitches that you can cut to fit your frame and weld in place. We offer a variety of drops so you'll want to do a bit of measuring on your Wagoneer to figure out the best drop to fit the receiver tube either through fascia or beneath it. Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3" Drop # 15901 9" Drop # C47CR 10.865" Drop # 15902 11-1/2" Drop # 15903 18" Drop # C99CR
  view full answer...
• Heavy Duty Trailer Hitch Receiver for 2020 E-450 Class C Motorhome
  Since there are no custom fit receivers for your 2020 E-450 motorhome you will need to use a universal hitch. The Curt Class 5 Universal Hitch # C47CR fits frames up to 44" wide. This is a weld-on hitch so we recommend taking it to a certified welder for installation. The maximum gross trailer weight of 16,000 lbs and tongue weight of 1,600 lbs is as heavy duty as it gets. Keep in mind, you will be limited by the towing capacity of your motorhome.
  view full answer...
• Front Mount Hitch Receiver Recommendation for a 2023 Ram ProMaster 1500
  For a front mount receiver I recommend checking out the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C47CR. This will give your 2022 Ram ProMaster 1500 a 2" front receiver and the brackets can be adjusted along the trimmable crosstube to fit a variety of applications. Since this is a universal-type installation you (or whoever is doing the installation) will be responsible for making sure it's installed correctly. I'm attaching a review video and the installation instructions for...
  view full answer...
• Trailer Hitch Receiver Options For A 2005 Ford E-350 School Bus
  Hi Jacob, The Curt Trailer Hitch Receiver # 14053 lists that it's a fit for cutaway chassis if the bolt holes are 38-5/8 inches from frame to frame. This would mean that the holes in your frame have to be spaced 38-5/8" from center to center in order for the hitch to work. With your vehicle be a school bus and the dimensions that you stated you'll likely have to go with a weld-on adjustable fit trailer hitch receiver. You'll want to measure the distance down from the frame to clear...
  view full answer...
• Trailer Hitch receiver For A 2011 Ford Expedition EL
  Hey Brian, That is correct, manufacturers do not offer a bolt-on trailer hitch receiver for 2011 Ford Expedition models. You'll have to go with a weld-on hitch and would need to measure the distance between your frame down to clear the bumper so that you can choose the correct drop: Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3" Drop # 15901 9" Drop # C47CR 10.865" Drop # 15902 11-1/2" Drop # 15903 18" Drop # C99CR
  view full answer...
• Trailer Hitch For RV on CHevy Express Chassis
  For the hitch, you'll need to go with a universal weld-on option, and since the frame is 42 inches apart, and you need a drop of at least 4 inches, the best option is the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C47CR. The # C47CR will give you a drop of about 9 inches from the frame (which is the closest available to needing at least 4 inches), and is for frame widths up to 44 inches wide. You mentioned Class 4 but I assume you're good with a Class 5 for that added bit of strength. Then...
  view full answer...
• Trailer Hitch Receiver Options For 1999 Ford E450 Ambulance
  The width of the mounting channel is 2-7/8 inches for the Draw-Tite Max-Frame Trailer Hitch Receiver # DT37GR. It's pretty unlikely this is going to fit, and for applications like yours, the best option is a universal hitch that you can weld on. So long as your frame is no longer than 44 inches wide from outside to outside, a universal hitch will work, you just need to measure how far down you need the receiver to be from the bottom of the frame (the drop). Once you know that, you can...
  view full answer...
  
• Recommended Trailer Hitch Receiver For A 1999 Toyota Prado RHD
  Hi Colin, Since there isn't a confirmed fitting custom-fit hitch for a 1999 Toyota Prado RHD the only option would be to install a weld-on adjustable-fit trailer hitch. We haven't had a Prado in to test it for a fit with a 4Runner trailer hitch unfortunately. We have a few different sizes depending on the drop you'll need to clear the rear fascia: Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3" Drop # 15901 9" Drop # C47CR 10.865" Drop # 15902 11-1/2" Drop # 15903 18" Drop...
  view full answer...
• Best Way To Use A Hitch Bike Rack On A Trailer
  I suggest getting a 2 inch hitch receiver for your trailer. A universal one like this # C47CR will work well. You just need to weld it into place. I don't recommend putting the Swagman Original # S64400 in anything other than a hitch receiver. Luckily the Swagman Original is rated to be put on any vehicle you may have with a class III hitch or higher so you're good to use it on the back of your 14 foot trailer!
  view full answer...
• Hitch Option For 2011 Chevy Express Cutaway Van
  There are no custom fits for a trailer hitch on your 2011 Chevrolet Express cutaway van, but you may be able to use a universal weld-on hitch. So long as your frame measures no more than 44 inches wide from outside to outside you can use the Curt Class 5 Universal Weld-on Hitch # C47CR.
  view full answer...
• Trailer Hitch Options For A 2019 Isuzu NPR With Rollback Flatbed
  Hi James, There isn't a custom-fit trailer hitch option available for your 2019 Isuzu NPR so you'll need to measure the distance between the inside of the frame rails and also the drop needed from the frame down to clear the rear bumper. We offer a variety of drops to accomplish this that I've listed out below: Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3" Drop # 15901 9" Drop # C47CR 10.865" Drop # 15902 11-1/2" Drop # 15903 18" Drop # C99CR These would all need to be welded...
  view full answer...
• Heavy Duty Hitch For 2013 Coachmen Leprechaun Class C
  I have a solution for you. I see a couple of options, you can go with the Class V Universal Weld-on Receiver Hitch and Brackets with 3" Drop # 15901. It is a weld-on hitch with a Gross Trailer Weight (GTW) of 15,000 pounds and a Tongue Weight (TW) of 1,500 pounds Or we have the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C47CR. This is a weld-on hitch with a GTW of 16,000 pounds and TW of 1,600 pounds. You will also need the brackets with this one. We have the 7" Weld-On Bracket...
  view full answer...
• Solution for Trailer Hitch Receiver on 1997 Toyota Hilux Surf SSR-X
  I do have a solution, but there are no custom fit hitches with a bolt-on installation for your 1997 Toyota Hilux Surf SSR-X. The only option is to use a universal hitch like the Curt Class 5 # C47CR. This weld-on hitch fits vehicle frames up to 44". We recommend taking it to a certified welder for installation.
  view full answer...
• Recommended Hitch for a 2011 Itasca Suncruiser 35P Motorhome
  Yes, there is and you are in luck because there is a custom fit option. The Curt Trailer Hitch item # C14082 will bolt directly to the frame of your 2011 Itasca Suncruiser 35P. This is a class IV hitch with a 2" receiver. It has a 10,000 lbs towing capacity and a 1,000 lbs maximum tongue weight. The Curt Trailer Hitch item # C14082 fits frames that are 34" wide. It also does require drilling as there are no predrilled holes for a hitch. If your frame is wider than 34" you will need to...
  view full answer...
• Recommended Trailer Hitch For A Foreign Model 2020 Ford Ranger FX4
  Hi Drew, The Curt # C97JR you were looking at is designed to fit select model Jeep Grand Cherokee L's and would not be a fit for your 2020 Ford Ranger. All of the custom-fit hitches we currently offer are designed for US models so you'd have to go with an adjustable-fit weld-on trailer hitch instead. These will come with a drop so you'll want to measure from the frame down to make sure the receiver tube will clear the bumper. Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3"...
  view full answer...
• Will The Draw-Tite Trailer Frame Hitch Receiver Fit A 1974 Chevy K5 Blazer With A Gas Tank Shield
  The Draw-Tite Max-Frame Trailer Hitch Receiver 75129 should fit with any OEM parts but just to be used I went out to the warehouse and measured the hitch. From the back of the crossmember tube to the center of the first bolt hole is 1". The distance between the inside of both mounting ears is 30-1/4". This hitch should sit directly under your frame rails so you can use that 1" measurement to see if the tube will run into interference with your gas tank shield. If this doesn't work then...
  view full answer...
  
• What Hitch do You Recommend for My 2012 GMC Savana Utility Van?
  Is the steel step bumper you have installed the factory bumper on your 2012 GMC Savana KUV Van?
  view full answer...
  
• Recommended Trailer Hitch for a Thomas Saf-T-Liner School Bus
  The best option to add a hitch to your 2006 Thomas Saf-T-Liner School Bus is going to be the Curt Class 5 Universal Weld-on Hitch w/ Brackets item # C97CR. This is a universal hitch that fits frames from 18" to 62" wide. This is our highest rated universal hitch and it has a 20,000 lbs towing capacity. The included brackets will drop of 9" from your bus's frame. There are no custom fit hitches for your Thomas Sf-T-Liner and this is going to need to be welded to your frame for the capacity...
  view full answer...
• Do You Carry a Bike Rack that Will Fit a Heavy Fat-Tire Electric Bike on a Motorhome or Fifth-Wheel?
  Yes! For an electric bike carrier that will accommodate fat bike tires and the torque on the rear of a motorhome and fifth-wheel trailer, I recommend the Hollywood Racks RV Rider Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount # HLY64FR. The RV Rider has an 80-pound per bike weight capacity and can hold fat tires up to 5 inches wide. In addition, the RV Rider is constructed with bolstered steel that is manufactured to withstand the extra torque. If you need a hitch receiver...
  view full answer...
• Hitch Options For Older Ambulance
  There may be an option for a hitch for your older ambulance, and you are correct you will need a universal hitch that is welded on. There are three options from Curt that will work with frames that measure up to 44 inches wide (from outside to outside), with the only difference being the amount of drop they give you from the bottom of your frame: - 3" Drop: Curt Class 5 Universal Weld-on Hitch # 15901 - 9" Drop: Curt Class 5 Universal Weld-on Hitch # C47CR - 18" Drop: Curt Class 5 Universal...
  view full answer...
• Parts Needed to Tow 1999 Jeep Cherokee With School Bus
  We do have some hitch solutions for you, but they'll need to be welded in place in order to install them, as none of the universal fit hitches we offer can be bolted on. What you'll need to go with is a universal-fit hitch designed for a service body truck, and in order to choose the correct one, you'll need to measure the needed drop, which is the vertical distance between the underside of the frame member and the lowest point of the rear bumper. You'd then choose the hitch with a drop...
  view full answer...
• Option For Heavy-Duty Hitch on Motorhome
  Since there isn't a custom-fit option for your motorhome, the only possible option for a heavy-duty hitch would be a universal, weld-on type. There are three options from Curt for frames that measure up to 44 inches (from outside to outside), with the only difference being the drop they provide (the distance from the bottom of the frame to the top of the receiver - 3" Drop: Curt Class 5 Universal Weld-on Hitch # 15901 - 9" Drop: Curt Class 5 Universal Weld-on Hitch # C47CR - 18" Drop:...
  view full answer...

Do you have a question about this Heavy Duty Receiver Hitch?