Will The Draw-Tite Trailer Frame Hitch Receiver Fit A 1974 Chevy K5 Blazer With A Gas Tank Shield
Question:
Will this trailer hitch fit a 74 K5 Blazer that has the OEM steel gas tank shield?
asked by: Jack G
Helpful Expert Reply:
The Draw-Tite Max-Frame Trailer Hitch Receiver 75129 should fit with any OEM parts but just to be used I went out to the warehouse and measured the hitch. From the back of the crossmember tube to the center of the first bolt hole is 1". The distance between the inside of both mounting ears is 30-1/4".
This hitch should sit directly under your frame rails so you can use that 1" measurement to see if the tube will run into interference with your gas tank shield.
If this doesn't work then you can go with the an adjustable-fit, weld-on hitch. You'll just need to determine the correct drop needed for the receiver tube to clear the bumper.
Draw-Tite
7" Drop # 41990-07
16" Drop # 41990-16
Curt
3" Drop # 15901
9" Drop # C47CR
10.865" Drop # 15902
11-1/2" Drop # 15903
18" Drop # C99CR
Products Referenced in This Question
Class V Universal Weld-on Receiver Hitch and Brackets with 3" Drop
- Heavy Duty Receiver Hitch
- Weld-On
- 18 - 44 Inch Wide
- 1500 lbs TW
- 15000 lbs GTW
- Class V
- 2 Inch Hitch
- 3 Inch Drop
- CURT
more information >
Curt Class V Universal Weld-on Receiver Hitch and Brackets with 10.865" Drop
- Heavy Duty Receiver Hitch
- Weld-On
- 18 - 44 Inch Wide
- 1200 lbs TW
- 12000 lbs GTW
- Class V
- 2 Inch Hitch
- CURT
more information >
Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2" Receiver - 60" Wide
- Heavy Duty Receiver Hitch
- Weld-On
- 18 - 60 Inch Wide
- 1500 lbs TW
- 15000 lbs GTW
- Class V
- 2 Inch Hitch
- 11-1/2 Inch Drop
- CURT
more information >
Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver - Weld On - Class V - 2"
- Heavy Duty Receiver Hitch
- Weld-On
- 44 Inch Wide
- 1600 lbs TW
- 16000 lbs GTW
- Class V
- 2 Inch Hitch
- 7 Inch Drop
- Draw-Tite
more information >
Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2" Receiver - 44" Wide
- Heavy Duty Receiver Hitch
- Weld-On
- 18 - 44 Inch Wide
- 1600 lbs TW
- 16000 lbs GTW
- Class V
- 2 Inch Hitch
- 9 Inch Drop
- CURT
more information >
Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2" Receiver - 44" Wide
- Heavy Duty Receiver Hitch
- Weld-On
- 18 - 44 Inch Wide
- 1600 lbs TW
- 16000 lbs GTW
- Class V
- 2 Inch Hitch
- 18 Inch Drop
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver - Weld On - Class V - 2"
- Heavy Duty Receiver Hitch
- Weld-On
- 44 Inch Wide
- 1600 lbs TW
- 16000 lbs GTW
- Class V
- 2 Inch Hitch
- 16 Inch Drop
- Draw-Tite
more information >
Featured Help Information
Instructions
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Recommended Trailer Hitch for a Volvo D13 Semi-Trailer
- Q&A: Trailer Hitch for 2010 IC Bus CE-Series
- Q&A: Measurements On Draw-Tite Trailer Hitch # 41952
- Q&A: Trailer Hitch Option for Mitsubishi Fuso Truck
- Q&A: Recommended Hitch for Towing a Car with Mitsubishi Fuso FE180 with Lift Gate
- Q&A: Inner Bracket Dimensions for Buyers Products Hitch Plate with 2" Receiver Tube - Ford
- Q&A: Solution for Trailer Hitch Receiver on 2006 Bluebird All American FE School Bus
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Embrace Winter Wanderlust: Celebrate Holidays with Harvest Hosts
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: How to Measure for Trailer Hitch Drop
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: Trailer Hitch Receiver Sizes