Brophy Swiveling D-Ring Tie Down Anchor - Bolt-On - 6-5/16" Wide - Recessed Mount - 2,000 lbs
(246 reviews)
Price: $32.42
In Stock
Brophy Swiveling D-Ring Tie Down Anchor - Bolt-On - 6-5/16" Wide - Recessed Mount - 2,000 lbs
Item # RR06
Our Price: $32.42
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (246)
- Q & A (0)
- Photos
Brophy Tie Down Anchors - RR06
- D-Ring
- Tie-Down Cleats and Rings
- 2000 lbs
- Trailer Tie-Down Anchors
- Truck Tie-Down Anchors
- Recessed Mount
- Brophy
This sturdy steel D-ring creates a stable tie-down point in your trailer or truck bed. Recessed design lets you roll cargo over the D-ring without interference. WLL is 2,000 lbs.
Utility Trailer D-Ring Tie Down
- Recessed Ring Swivels 360 Degrees
- Zinc Plated
- Bolt-On Design
- Capacity: 6,000 lbs.
- Safe Working Load Limit: 2,000 lbs.
- 4 bolt holes are 3-13/16" apart
- Bolt holes are 1/4" in diameter
Note: Tie-down anchors must be chosen according to their safe working load limit (WLL). The weight of the secured cargo must not exceed the combined WLL of the anchors being used. For example, if you are using anchors with a WLL of 100 lbs each to tie down a load weighing 400 lbs, then you need at least 4 anchors to safely secure that load. It is recommended that you always use anchors in pairs.
RR06 Trailer D-Ring Tie Down, Recessed Swivel
Customer Satisfaction Score:
100% were satisfied with this product
0% of customers were not satisfied
Customer Reviews
Brophy Swiveling D-Ring Tie Down Anchor - Bolt-On - 6-5/16" Wide - Recessed Mount - 2,000 lbs - RR06
Average Customer Rating: 4.7 out of 5 stars (246 Customer Reviews)
This sturdy steel D-ring creates a stable tie-down point in your trailer or truck bed. Recessed design lets you roll cargo over the D-ring without interference. WLL is 2,000 lbs.by: Morgan08/05/2019
Good, solid piece. 2K WLL and 6K break strength are higher than most other comparable swivel D-rings and flush mount D-rings. I have a steel deck trailer and one of my flush mount D-rings failed so I replaced all 4 with these. Being as mine is steel deck, welding is a solid install. I trimmed the edge flange for a tidy fitment for surface mount but later decided to just mount from below and weld in from the top. It came out very nice, I suggest similar mounting for those with steel trailers. of course, I had to grind off the zinc from the weld zone and painted with rustoleum both on top and from below.
by: Cody 02/09/2024
Good pricing, fast shipping, great customer service. You can feel the quality of the product unlike other suppliers. Mounted these in our enclosed trailer with ease. The instructional video takes you step by step. Waited to write the review until after hauling a couple of vehicles, the swivel feature is VERY convenient.
by: Mike 04/04/2023
these are the best one i have ever installed and very well made no problems with them at all
Mike
4/5/2024
very good
by: Randy R.06/27/2016
I do like these swiveling d-rings and the metal backings. They are going to make it so nice to tie stuff down. There are one in each corner of my trailer.
by: Vallencourt Construction08/03/2023
These Dring were perfect for up fitting our 550 flat bed parts truck. We threw these on the inside of the side gates for easier tie downs without bending the gates. These have not had any issues from daily wer and tear hauling anything from 10lbs to 2000lbs.
by: David 04/24/2024
Very good product
by: Dwayne C.10/18/2016
Brophy swiveling D ring tie downs are pretty awesome. Super heavy duty, really like the Swivel design. By having the freedom of movment the ancor is never in a bind, at any angle and tension is pulled evenly from any direstion. The matching backing plates are a must as far as I'm concerned. Installation was easy. All holes on the backing plates ligned up well. No issues. I will give it up to etrailer.com also for the fast shipping. It means alot when you have a project going on. Over all satisfied with my purchase.
by: Douglas 05/08/2024
Pretty fast delivery and as advertised.
by: James 08/12/2018
Called customer service because I wasn’t exactly sure what I wanted. Talked to Molly and she pointed me in the exact direction I wanted to go. She even helped me save some money by not buying the kit with the hardware because I wanted to use stainless steel carriage bolts for a flush finish on top. Only modification I had to make was drill the holes out bigger on tie down to except the square shank on the carriage bolt.
by: Terry H.04/01/2015
This is exactly what I was looking for. I installed 4 of these in my enclosed cargo trailer to make it a car hauler for my 1956 Jeep CJ5. They were easy to install and they'll work great.
Terry H.
4/1/2016
Theyre working exactly as I had hoped. Ive towed my trailer with the Jeep on it about 1500 miles to various events without one problem.
by: Alex 08/11/2023
Excellent Service, will use again thanks
by: Jeeper07/04/2016
Tie downs work good for securing my rig and look good after a year of use on my trailer. They do need a drain hole drilled in the bottom to let rain water escape and not accumulate.
by: Bill Edwards06/03/2017
Product is fine not a single thing wrong with it. That said it was the manner in which the order was shipped and the packaging. Heavy metal items with sharp corners were placed unwrapped or retained in a box with soft and polished plastic finish, absurd!
I got lucky, the plastic cover on the Weathertech items protected them from damage. Longer shipping they would have not made it.
by: Scott07/05/2019
Great customer service and super fast delivery. Product is great too! Will definitely make our trailer more versatile.
Scott I.
7/6/2020
The tie downs have worked great. I had to drill some drain holes in them but other than that they are definitely more versatile than other tie downs.
by: Michael12/24/2018
I needed 8 tie downs for a new trailer in addition to the four that came with it. etrailer had exactly what I needed. On line ordering was simple and quick. Shipment arrived quicker than I thought, two days later. Great product and service!
by: Boomer G07/19/2020
Had to buy a 4 3/8 hole saw to install. Very happy with the results. Need to make sure your hold down strap hooks are big enough for the D-ring.
by: Drew 10/08/2021
Overall I really like these things and they have worked well. My only complaint is that on my utility trailer they are exposed and there is no way for water to drain out of them. I'm thinking about drilling a hole(s) to avoid this problem. No signs of rust though
by: Dean S01/31/2018
Parts always show up in a timely manner. Always have what I need in stock. Great Customer Service!!!! I have ordered Fifth wheel hitches to trailers parts and have always been happy with the products I have received!!!
by: Eric 11/30/2022
As expected. Lightning fast delivery
by: Darren F10/22/2022
I think they need a couple of drain holes in the bottom of the plate for water drainage
by: dc08/28/2012
the products ordered were as described and are great quality parts that will play a great role in upgrading my enclosed R&R all aluminum trailer. the product selection etrailer has is second to none and i will shop here first next time.
the shipping of the products were top notch, for as they arrived in a very timely manner. great job etrailer!
by: Ed05/12/2023
Just what we needed !!!
by: Lloyd02/11/2016
It was a great experience working with etrailer.com. I ordered my products, and a couple days later they arrived at me house.
by: warren04/27/2017
great product very well built eazy install recomend backing plate
by: Randy G.03/31/2017
didn't install yet but look heavy duty and are the same as the factory ones on my trailer.
25
245
Show More Reviews
See what our Experts say about this Brophy Tie Down Anchors
- Hardware for Brophy Swivel D Rings Part # RR06Installation hardware is not included with the Swivel D Ring part # RR06 due to the unknown nature of the surface that the end user will attach it to. Depending on the weight of the object that will be held down, and the thickness of the surface it will be attached to, you also might want to consider the backing plate part # BP06.
view full answer... - How to Install the Trailer D-Ring Tie Down # RR06 on a TrailerIf you look below the specs for the Trailer D-Ring Tie Down, # RR06, you will see that the lip is wider than the base . You would need to drill a hole that is 4-3/8 inches in diameter for the base to fit through and then use screws appropriate for the surface it is mounted to in order to secure it. It is recommended to use the backing plate # BP06 under the service where the D-Ring is installed to maximize its capacity and offer support. In order to drill out the hole you can use a large...
view full answer... - Are Backing Plates Alone Sold For Brophy Swiveling D-RingsYes, for the Brophy Swiveling D-Ring Tie Down Anchor # RR06 there are backing plates available by themselves, with the correct part being the following: - Backing Plate for RR06 Recessed Swivel D-Ring Tie Down # BP06
view full answer... - Difference Between Brophy Swivel D-Ring Anchors # RR6K and # RR06The only difference between the Brophy # RR6K and # RR06 is that the RR6K includes the backing plate and mounting hardware while the RR06 is just the D-ring unit alone.
view full answer... - Does the Brophy Swiveling D-Ring Tie Down Anchor Come with Backer PlateThe Brophy Swiveling D-Ring Tie Down Anchor part # RR06 does not come with a backer plate and it's not typically used with one. The backer plate is not required but if you wish to use one you'll need to construct this on your own.
view full answer... - Availability of Tie Down Anchor that Mounts Flush on Mounting SurfaceFor a D-ring tie down anchor with a similar capacity and doesn't require a recessed mount we have the part # SS15-C which has a 1,600 lb capacity. I attached a review video for this anchor for you to check out as well.
view full answer... - Difference Between Brophy Tie-Down # RR06 And # RR6KThere is no difference between the D-Ring Tie Down, part # RR06 and the tie-down that is included in the # RR6K other than the backing plate and the mounting hardware. the D-Ring is the same for both of these items. These have a capacity of 6,000 lbs and a safe working load limit of 2,000 lbs. These are a bolt-on design. The recessed ring swivels 360 degrees. I have attached a photo of the tie-down that shows the dimensions you can check out.
view full answer...
- Backing Plate Availability for the Brophy D-Ring Anchor RR06For the backing plate of the Tie Down Anchor part # RR06 you would want the part # BP06.
view full answer... - How to Determine Proper D-Ring Spacing In an Enclosed Car Hauler TrailerSince you are planning on installing these Trailer D-Rings # RR06 in a plywood floor I would recommend you also get the Backing Plate # BP06 to offer better support than just the wood of your trailer floor. As far as the placement of them in your trailer, you will need to consider what vehicles you will be transporting. If it will be only one vehicle I would recommend loading that car in the trailer and then strategically place the D-rings to give you the best possible mounting points...
view full answer... - What Size Mounting Hardware is Required to Install the Trailer D-Ring Tie Down, # RR06The Trailer D-Ring Tie Down, # RR06, has mounting holes that are 1/4 inches in diameter. We recommend using backing plate # BP06 when installing this tie down to provide support for the tire down.
view full answer... - What are the Dimensions of the Brophy D-Ring Tie Down RR06I pulled the Brophy Trailer D-Ring Tie Down, # RR06, from my warehouse to measure and verified that the diameter of the flange is in fact 6-5/16 inches. I also verified that all other measurements on the product page are correct. I have attached the photo of the dimensions for you to reference. We recommend using the backing plate, # BP06, with this tie-down to provide extra support when securing cargo.
view full answer...
- Can Brophy D-Rings be Drilled to Allow Water to Drain OutSince you already have the D-rings # RR06 you could drill a couple of small 1/16 inch or smaller holes at the lowest part of each ring housing to allow water to drain out. The D-rings are zinc-plated to resist corrosion so that will also help.
view full answer... - Does Brophy Swiveling D-Ring Tie Down Anchor # RR06 Have Capacit for Use with Car HaulerThe Brophy Swiveling D-Ring Tie Down Anchor # RR06 would work great in a car hauler application like yours. Each of these has capacity of 2,000 lbs working load limit and 6,000 lbs break strength so with a few of these securing a vehicle you'd have more than enough capacity. Welding a zinc coated steel is possible but requires a lot of ventilation!
view full answer... - Depth Needed To Mount Trailer D-RingI pulled a trailer D-Ring from our warehouse and took a measurement for you. the depth of the D-Ring housing from the bottom of the flange with the mounting holes is 7/8 inches. The 1/4 inch mounting holes are spaced 3-3/16 inches apart. The mounting plate you would use under the surface you are mounting the D-Ring to, is part # BP06. This would offer much more support than just wood.
view full answer... - Availability of CR Brophy D-Ring Tie-Down Without Countersunk HolesWas it the holes themselves you weren't wanting, or the fact that they're countersunk that you don't care for? Brophy doesn't make a similar tie-down anchor without holes, but they do offer some with holes that aren't countersunk like part # RR05 with a 5K max load, or 1600 lb safe working load limit. There's also the # RR06 with a 6K max, 2000 lb safe working load limit. For a more secure installation, there's backing plates available, if you went with the # RR05, you'd use the # BP05...
view full answer... - Can the Brophy Swiveling D-Ring Tie Downs Be Used To Secure a 5,000 Lb Vehicle with Backing PlateThe Brophy Swiveling D-Ring Tie Down Anchor part # RR06 with the Backing Plate for RR06 Recessed Swivel D-Ring Tie Down part # BP06 are a great, easy to install set of tie-downs which can be used for securing a vehicle. The tie-downs themselves have a 2,000 lb working load limit. That said, you will be limited by the attachment point if lower. It would be very difficult for me to give a definitive answer of the weight capacity limits of your floor so for this I must recommend you reach...
view full answer... - Parts Needed to Mount the Swiveling D-Ring on a Steel Deck TrailerAs long at you have the appropriate size bolts and hardware for the D-Ring Tie Down Anchor # RR06 you will not need the backing plate. The backing plate # BP06 wouldn't offer your D-ring anymore support than the steel frame itself would, but it could come in handy as a nice template for drilling the holes in your equipment trailer.
view full answer... - How to Mount the D-Ring to a MC10 Motorcycle Trailer for Strapping in a Honda GoldwingYou would need to drill a hole that is 4-3/8 inches in diameter for the base to fit through and then use nuts and bolts appropriate for the surface it is mounted to in order to secure it. It is recommended to use the backing plate # BP06 under the surface where the D-Ring is installed to maximize its capacity and offer support. In order to drill out the hole you can use a large enough hole saw drill bit or use the backing plate as a template and a pencil to mark the diameter needed and...
view full answer... - Recessed D-Ring Tie Down Recommendation for a TrailerThe D-Ring part # RR06 has a 2,000 lb capacity. That is the only recessed mounted D-ring we carry that has a capacity between the # RR01C and the # RR05. I would recommend you go with more capacity that you need as opposed to less than you need.
view full answer...
Do you have a question about this Tie Down Anchor?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Jeffrey L
Updated by:
Laura H
Updated by:
Jacob W
Video by:
Dustin K
Video by:
Zach D
Installed by:
Cole B
Installed by:
Randy B
Installed by:
Hayden R
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Morgan D.
8/6/2020
1yr update: these still are working fine with one flaw. There is no drain hole. the cups easily fill with water of course that should have been obvious from the start. Its hot here in Texas and I assumed the water would evaporate quickly with no changes but it doesnt. I first drilled a 18 hole near the bottom rounded corner of the cup to drain the water, which works if it wasnt for the debris. They also easily collect various plant debris unless you store yours in a garage which is unlikely for this type of trailer. so the 18 hole clogs. next I went to a 316 hole. It still has the propensity to clog. plant debris + standing water = rust. Im unsure of how big of a hole you can go before you begin to compromise the strengthrating of the cup & tie down assembly. These should have been designed with the appropriate sized hole already cut, or at least a guideline of how big and where I could drill my own holes. Unless you need the flush mount swivel kind, the surface mount D-Ring type would eliminate this long term failure mechanism cup rusting out. No, the plating wont protect it forever and I painted any exposed metal to combat any issues.