Hardware for Brophy Swivel D Rings Part # RR06

Question

Question:

Do these D rings come with bolts, washers, and nuts?

asked by: will c

0

Expert Reply:

Installation hardware is not included with the Swivel D Ring part # RR06 due to the unknown nature of the surface that the end user will attach it to.

Depending on the weight of the object that will be held down, and the thickness of the surface it will be attached to, you also might want to consider the backing plate part # BP06.

expert reply by: Mike L

0

Answer 1

For the Alpha Systems Alphabond Repair Tape for RV Roofs #AL32KV the adhesive is 23 mils while the TPO facer is 4 mils and the release liner is 2 mils. I confirmed this directly with my contact at Alpha Systems. Attached is a review video for you to…

view full answer...

Answer 2

The Trailer D-Ring Tie Down, #RR06, has mounting holes that are 1/4 inches in diameter. We recommend using backing plate #BP06 when installing this tie down to provide support for the tire down.

view full answer...

Answer 3

Since you are planning on installing these Trailer D-Rings #RR06 in a plywood floor I would recommend you also get the Backing Plate #BP06 to offer better support than just the wood of your trailer floor. As far as the placement of them in your…

view full answer...

Answer 4

The Brophy Swiveling D-Ring Tie Down Anchor part #RR06 does not come with a backer plate and it's not typically used with one. The backer plate is not required but if you wish to use one you'll need to construct this on your own.

view full answer...

Answer 5

I went out into our warehouse and measured the Backing Plate #BP06 and found that the outside dimensions are 6-7/16 inches by 6-1/2 inches. The circle in the middle has a 4-5/8 inch diameter and the overall thickness of the metal plate is .11 inches…

view full answer...

Answer 6

For the backing plate of the Tie Down Anchor part #RR06 you would want the part #BP06.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Hardware for Brophy Swivel D Rings Part # RR06

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching