Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we'll be taking a look at the Toledo Replacement Shock Absorbers, for Toledo Brake Actuators. Part number, 1844-2. Now with the old shock you can tell that it's worn out by looking at the bushings for one, 'cause they're all cracked and corroded, as well as it really doesn't function the way it should and have the pressure that it should either. It's going to be really spongy and not really work the way they should. Let's go ahead and look at how it operates when it's new. Now us putting pressure on there, you can see how it has a lot of resistance and it isn't going to be really spongy, like it was before, so this will actually actuate those brakes a lot quicker and a lot more efficiently then that burned out shock would. Well the first thing we're going to have to do in the instillation of our shock, is go ahead and remove the shock and the hanger for the receiver that's holding it in place. We're going to lube up, the 2 nuts right here on the bottom, as well as on the other side over here, and the bolt that hangs the rear of the shock here on the back. Now we're going to pull off this last one here and drop down the receiver and the shock.
You can see that shocks completely blown out, but the bushing is completely shot. Now we're going to go ahead and pull out this bolt here, so I'll spray it down and pull it off while we use the same hardware. Put the new one in place. Place the bolt in and tighten it back down. Now let's go ahead and get it back into place. Go ahead and slide our bolt through and then out the other side.
We reattach our nut and tighten it down. Now we'll raise the front back up into position. Go ahead and knock these out a little bit, just to give us a little extra room to work, and lift it up into place. All right with that side back on let's go ahead and put our plates back on the outside, and place all of our nuts back on. And that will do it for the Toledo Replacement Shock Absorbers, for Toledo Brake Actuators. Part number 1844-2. (Video Information: etrailer.com, expert service, lowest prices, fast shipping.
800.298.8924).
Average Customer Rating: 4.8 out of 5 stars (23 Customer Reviews)
Etrailer had the part for my trailer coupling that was hard for me to find anywhere else. I got it two days earlier than what I paid for in shipping . From now on E Trailer will be my first stop when I need something for my trailers
Straight forward replacement for my M101A2 trailer surge brakes. Shipped quickly and fitted perfectly, can't wait to test it out.
Snowmog
6/20/2015
Surge brake applies so smoothly now, hardly know the trailer is there.
Item fit perfectly on my m101a2 military surplus trailer. Arrived on time and in excellent shape. Once I set up the brake lines I have no doubt this will work perfectly.
Richard J.
7/24/2014
Both the jack and the surge brake part are still performing well. I dont have any complaints except that the surge brake part must be painted to prevent rust. Other than that its good.
Worked perfectly for my M101A3 US military trailer. So nice to have it working properly again!
Dayne M.
3/1/2018
Still awesome! Working great!
Replacement was great and works perfect ly
this is a exact replacement which I was surprised as my trailer is 25 years old thankyou
Del
10/5/2014
Still working great
5000 miles on my equipment trailer. Brakes work as advertised. No problems, etrailer shipping prompt and complete.
It was a duplicate of the original. Anyone looking to rebuild a military trailer with surge brakes would do well to check out this product.
Product is exactly what I needed to fix my trailer surge brakes from from bucking. The brakes are applied and released too quickly with a worn out shock absorber, the only problem is it was very pricey!
exact replacement for my m101a2. the orignal was made by monroe and I contacted monroe only to find out they did not offer a replacement, this one is made by gabriel and as I stated it is a exact replacement. shipping was fast, I ordered on a friday morning and it was at my door tuesday morning even with monday being a holiday.
Seems to be the correct replacement part for my military trailer. Not an easy part to find.
Reduced premature braking with trailer. Used on M101A3 Military Trailer for a Toledo hydralic braking system.
perfect fit, operated as it should.
The best customer service I have had in a while. My part was back ordered but Tonya kept updating me. Got my part it works great I can use my trailer again. Thanks etrailer.
Very fast order processing and timely delivery. Will definitely use this site again.
Not installed yet no comment
came as described, thank you.
worked great!
Product was exactly what i ordered and arrived in perfect condition.
Fast shipping. Installed and works as p romised.
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
George M.
1/10/2018
Perfect