Tekonsha Custom Wiring Adapter for Trailer Brake Controllers - Pigtail - Ford

See what our Experts say about this Tekonsha Accessories and Parts

• Which Plug Under The Dash Is The Factory Brake Controller Plug On A 2001 Ford F250 Super Duty
  On your 2001 Ford F250 Super Duty with the towing package the brake controller plug connector is located under the dash, near the steering column. You will be looking for a 6 prong rectangular plug. The location for the plug should be under the steering column toward the left. If you have the factory brake controller adapter it will plug into the plug under the dash and the bare wires will be attached to the brake controller color to color. If you need a brake controller wiring adapter...
  view full answer...
• Installing a Brake Controller on a 2002 Ford Ranger with Factory 4 Pole Harness
  You will need to hardwire an adapter to your 2002 Ford Ranger. We sell a Brake Controller Installation Kit with a 6-Way and 4-Way connector, part # ETBC6 that includes the adapter and the necessary wiring and components to complete the installation all by yourself. With this kit, you will not need to purchase any adapter separately. As a side, note, please be sure that the connector on the camper has a total of 6 pins. That is, it has 5 pins in a circle and one in the center. If it has...
  view full answer...
• Brake Controller Wiring for a 2003 Land Rover Defender SW
  The Universal Brake Control Wiring Adapter Ford, Land Rover, Lincoln, Mercury, part # 3035-S, will fit Land Rover LR3 and Range Rover within the model years 2005-2007. We do not have a plug-in adapter for the 2003 Land Rover Defender. That would lead me to believe that there is not a port under the dash of that year, make and model of vehicle. You will need to hardwire your Land Rover to accommodate a brake controller. You can do so with the Brake Controller 7 & 4 Way Installation Kit,...
  view full answer...
• Parts Needed To Install Tuson DirecLink Trailer Brake Controller On 2003 Ford Expedition
  Yes, in order to install the Tuson DirecLink Base Model Trailer Brake Controller part # 335DL-100 on a 2003 Ford Expedition with factory 7-way you'll need the Tekonsha Custom Wiring Adapter for Trailer Brake Controllers part # 3035-S. This way, you won't have to do any actual splicing into the vehicle.
  view full answer...
• Wiring a 2007 Ford F-150 for Electric Brake, Charging Circuit, and Auxiliary Reverse Light Circuit
  To add a brake controller in the cab of your 2007 Ford F-150 you will need a brake controller, like the Tekonsha P-3, item # 90195, and a brake controller wiring adapter. If you use the P-3 mentioned here you will need the # 3035-P Ford wiring harness. If you have a brake controller you will need the # 3035-S wiring harness to splice to the wires on the brake controller and plug into the brake controller port under the dash of the vehicle close to the OBD-II diagnostic port. To add the...
  view full answer...
• Female Brake Controller Harness for 2013 Ford F-53 Chassis
  We do carry Pigtail # 3035-S for your 2013 Ford F-53 Chassis.
  view full answer...
• Dash Thickness Requirements to Mount Redarc Tow-Pro Elite Brake Controller Remote Head
  The remote head of the Redarc Tow-Pro Elite # RED44FR can be mounted directly to the dashboard, to the center console, or through a spare knock-out switch panel. The Universal Mounting Panel # 331-TPSI-001 can be used on dash panels that are up to 7mm (9/32 inches) thick. If you choose to mount the remote head directly to your dash, or center console, the dash needs to have a thickness of 2 to 3mm (1/16 to 3/32 inches) and have at least 3-1/2 inches of space directly behind it to account...
  view full answer...
  
• Recommended Brake Controller Compatible with 2002 Lincoln Navigator with Factory 7-way and Tow Pkg
  For your 2002 Lincoln Navigator I recommend you choose a brake controller based on the style desired inside your vehicle. If you want absolutely no changes to the inside of your vehicle, you can use the Curt Echo Wireless # C51180 which will use a mobile app for setup and manual override. If you want a hardwired system with minimal change to the dash of your vehicle, I recommend the Redarc Tow-Pro Elite # RED44FR which has a small dash insert option and uses the hardwired box in a more...
  view full answer...
• What Vehicles Does Brake Controller Wiring Harness 3036-S Fit
  Brake controller wiring harness # 3036-S has replaced the 20272 and will fit the following vehicles: 2009 - 2015 Ford, F-150, All Styles 2012 - 2013 Ford, Flex, with Factory Tow Package 2012 - 2015 Lincoln, MKT, with Factory Tow Package If you have a 2003 Ford Expedition you would need harness # 3035-S.
  view full answer...
• Pin Out of Brake Controller Connector on 2021 Land Rover Range Rover Sport
  Other than some slight cosmetic changes, there haven't been any appreciable changes in the chassis of the Land Rover Range Rover Sport since the first model year of the 2nd generation in 2013. Tekonsha/Draw-Tite nor the rest of the companies have tested the pinout of the 2021 model, but there's no reason to believe it's been changed from the 2020 model. I've heard nothing that indicates the pinout of the 2021 is any different, but you can confirm this for yourself as described below. The...
  view full answer...
  
• How to Install Powerstop 500-PS Brake Controller to 2002 Ford F-150
  I looked up the installation instructions for your brake controller. I don't have a diagram, but I'd be happy to run through how the controller should be wired. The green wire from the controller attaches to the cold side of the brake stoplight switch, the white ground wire attaches to the negative battery terminal, the red wire supplies 12-volt power to the controller, and attaches to the positive battery terminal. The blue wire carries the brake controller output. Connecting the orange...
  view full answer...
  
• Proper Brake Controller Wiring Harness for a 2005 Class C Motor Home On a E Series Ford Chassis
  Connecting a brake controller on your E series, van chassis, motor home can be done one of two ways. You can use the brake controller connector, item # 3035-S, to connect to the connector under the dash, if it is supplied, or you can hard wire the connector. From the pictures you sent it looks like the connector that is not in use could be the correct connector. The connector that is in use looks very similar also and is in the normal location that our installer said the connector should...
  view full answer...
• Brake Controller Wiring Harness Needed for a 1999 Ford F-150
  If you have a Tekonsha or Draw-Tite brand of brake controller with the 4 wire port in the back of the brake controller housing, the Tekonsha Wire Replacement for Ford, Lincoln, Mercury, and Land Rover Vehicles, item # 3035-P, will be the correct wiring harness for brake controller installation. If you have a brake controller with 4 wires exiting the rear of the controller you will need the Universal Brake Control Wiring Adapter Ford, Land Rover, Lincoln, Mercury, item # 3035-S, to connect...
  view full answer...
• Additional Parts Needed for Redarc Tow Pro Elite Installation on a 2000 Ford F250
  Good news! First, the RedArc Tow Pro Elite # 331-EBRH-ACCV2 is an awesome choice; I also checked your order and since you ordered this from the fit guided page for your vehicle, it comes with the # 3035-S wiring adapter for electronic brake controllers that you'll need to install it directly into your 2000 Ford F-250. That would be the only additional wiring required for this installation.
  view full answer...
• Does Brake Controller Need to Face Specific Direction to Function
  If you are installing a proportional brake controller in your vehicle then it does matter the orientation of the controller as the sensor needs to face the correct direction to work properly. The P3 part # 90195 has the most flexible mounting orientation. I attached a picture of how it can be mounted. A time delayed controller does not have same direction requirements.
  view full answer...
  
• Troubleshooting Reese Brakeman Brake Controller Wiring to Factory Harness
  The Reese Brakeman is not a controller we carry, but it is wired in the exact same way as the other controllers for your 2008 Ford F-150. The controller has 4 wires: black is 12V input, blue is brake controller output, red is brake light switch, and white is ground. If you have the factory 7-way, then I recommend the Tekonsha Custom Wiring Adapter for Trailer Brake Controllers - Pigtail - Ford # 3035-S which will allow you to simply match the colors for the factory plug because the functions...
  view full answer...
• Electric Brake Controller Wiring on 1997 Ford E-350 with 7-Way Trailer Connector
  If your 1997 Ford E-350 came with a factory 4-way versus a 7-way then the wires to the brake controller output would not have been run. You will need to run the wiring the entire way from the battery to the dash and then to the 7-way. You can use kit # 5506 for that connection which is just the wiring and circuit breakers from the # ETBC7 kit. I've attached an article and video to assist. If you have the factory 7-way it should have already been run all the way to the connector, so...
  view full answer...
• Compatibility of the Pilot Brake Controller # 80550 on a 2008 Ford F-150
  Yes the Piolet Brake Controller, part # 80550, will work with your 2008 Ford F-150. 4-way connectors do not have a provision for brakes, so if you have a trailer with a 4-way connector, it should not have brakes on it. It will work fine with your factory 7-way connector and the 4-way will still function normally. You will also need part # 3035-S to connect the brake controller to the brake controller port on your F-150. I have included a review video on the Pilot Brake Controller and...
  view full answer...
• Recommended Brake Controller for 2018 Fleetwood Bounder Coach on F53 Chassis
  For your 2018 Fleetwood Bounder Coach, I recommend using the Prodigy P3 # 90195 if you want the LCD screen for information and then using wiring harness # 3035-P for connection under the dash. If you want a clean look with a really nice brake controller then I recommend the # 3035-S and the Redarc Tow-Pro Elite Trailer Brake Controller # RED44FR. This will give you a clean dash look and still accessibility and control. I've attached a couple videos to assist.
  view full answer...
• Wiring And Adjusting The Tekonsha Voyager Brake Controller, # 39510, On A 1999 Ford F250/F350
  I am sending a link to the instructions for the Tekonsha Voyager Brake Controller, # 39510. It will show you how to adjust the brake controller. They do not have a wiring schematic, but I can explain how to wire it to a 1999 Ford F250/F350 truck. If your 1999 Ford F250/F350 has a factory installed 7-Way trailer connector, all you would need is the brake controller and the factory brake control adapter that connects to the controller and plugs into the OEM plug. The OEM plug is located...
  view full answer...
• Brake Controller Wiring Harness Recommended for 2004 Ford Expedition
  We do indeed have a harness that would work for you. The actual plug and play harness you need will depend on who manufactured the brake controller you have. I'll run through some of the major players and the part number for the compatible harness: • Tekonsha, Reese or Draw-Tite, use # 3035-P • Curt, use # C51322 • Hayes, use # HA81783-HBC • Redarc, use # RED87FR • Hopkins, use # HM47715 If your controller is from a different manufacturer or just has blunt-ended wires exiting the rear...
  view full answer...
• Recommended 7-Way Upgrade Kit For A 2002 Ford F-250 With A Factory 4-Flat
  If you're trying to just add a 7-way to your 2002 Ford F-250, and you've already got a 4-flat then you'll just need the: -Curt Trailer Connector Adapter # C57672. This adapter will plug into your existing 4-flat, and will splice to your battery, brake output wire, and 12v power. There is not going to be a plug under your dash for this to splice into, but the good news is you do not need to wire everything from scratch since you've already got a 4-pole. As far as plugging in your actual...
  view full answer...
• Can I Use the RedArc Tow Pro Liberty on a 2011 Ford Expedition
  Yes. You can use the RedArc Tow Pro Liberty # RED24FR with your Reese Multi-Plug Wiring Harness for Factory Tow Package - 7-Way and 4-Way Flat Trailer Connector # 74682; it really doesn't matter since it doesn't directly plug into the brake controller. With that said, since that is not the factory trailer connector, unless the # 74682 was replacing a factory trailer connector you will need to hardwire in the RedArc Tow Pro using # RED69FR; a wiring adapter like the # 3035-S cannot be used...
  view full answer...
• How to Install a Brake Controller On a 2006 Ford F-150 With 7-Way Trailer Towing Package
  Installation of your brake controller should be very easy with the factory 7-way trailer connector on your vehicle. All you will need to complete the installation is the Universal Brake Control Wiring Adapter Ford, Land Rover, Lincoln, Mercury, item # 3035-S. You will wire the like colors on your brake controller to the plug in adapter and mount the brake controller in an accessible location your installation will be complete. You have the wiring colors and functions correct. The connector...
  view full answer...

Do you have a question about this Accessories and Part?