Summer Starts Here - Save up to 70%
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Replaces your power landing gear follow leg and snap pin. Enjoy the power setup while you are out camping and know that your RV or fifth-wheel will be steady and secure.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today I'm going to take a look at the replacement fifth-wheel RV landing gear follow leg with the snap pin for Lippert Components RVs. This will replace your follow leg and snap pin on the Lippert Components power landing gear. It's designed to fit the standard power landing gear, supports your fifth-wheel to prevent unwanted movement. It's designed to connect right here to the lead jack and the landing gear set, with a connecting rod or a cross shaft, which we do sell separately. It does include the two zerk grease fittings, one right here, one right here for lubrication of the jack. This is constructed of a heavy-duty steel, has a nice black powder coat finish to it.
Part is made in the U.S.A.A few specs on this, the weight capacity. If it's a manual crank is going to be 4,000 pounds per leg. If it's a dual motor, it will be 4,000 pounds per leg. And if it's a single motor it'd be 2,500 pounds per leg. Overall height, which will be measured from the top to the very bottom of the inner tube right there, if we put a tape measure on that right here ...
Very top here you're going to see is right at 32 inches overall height. Total width on this going to be right at 2 1/2 inches wide. Now the outer tube, which is the black portion from here to the very bottom on the black tube, that's going to be right at 29 1/2 inches tall.And then the bracket stops or the weld stops right here on each side. This is where your jack will attach to the mounting brackets on your trailer. Outside the outside, which will be from here to down here.
You're going to be looking right at 17 1/2 inches, and inside the inside, 15 1/2 inches. So, each weld stop is about an inch wide. But that should do it for the review on the replaces fifth-wheel wheel RV landing gear follow Leg with the snap pin for the Lippert Components RVs.
Average Customer Rating: 4.9 out of 5 stars (106 Customer Reviews)
Replaces your power landing gear follow leg and snap pin. Enjoy the power setup while you are out camping and know that your RV or fifth-wheel will be steady and secure.Landing gear works great just like original equipment. It took about 7 hrs. to remove and install due to very tight working quarters and I am pretty handy with all the proper tools needed and some, so be patient, not as easy as the you tube video I saw.
So far so good!
Need to see my response under the Lead landing gear. Perfect fit and easy installation.
Needed a new landing leg for my 5th wheel, You guys made it soo easy to find the right part, and a great price, great quality, and fast shipping.
Great people! Love working with them!
Bill
8/24/2023
Still working as expected.
They are easy to install and work great.
great product with easy install ,customer service and knowledge is fantastic,you have a customer for life
Thank you for your assistance. Not only did we finally get the correct part but also assisted in being able to ship back the "wrong part". Not to mention the quick delivery.
was a direct fit. worked great.
Product is better than new, love the added grease fittings(zerks), this will provide a way to lubricate them for a much longer lasting.
I received the product sooner than expected from ETRAILER, however our local UPS could not deliver for a few days due to stormy conditions.
I installed the jack this morning and was back in operation sooner than expected.
Great product, great service and super customer service representative (John) to work with.
Thank you
Anthony R.
9/9/2017
Great, very happy with product
I replaced both the left and right side landing gear jacks and they fit perfectly and were easy to install. They also have the zerk fittings so they can be greased.
Guyn
1/24/2018
no problems after a year, working fine.
Shipping was fast however still have not installed yet.
Fit perfect. Exactly as described and fast delivery . A replacement follow leg for my 5th wheel...Great company to get products from.
Stanley
9/14/2019
Flawless....
First i would give 10 stars if i could, my part was lost in shipping by ups, i called Pat in customer service and Boy what service, she shipped out another part that day, Thursday and i received it on Friday, the next day. Everything fit perfectly, to those of you that need to order this part check all the measurements and if your are the same it will fit with out alterations . I just can't say enough about this company and this is the very first time i have used them, it won't be the last and i have told all my RV friends that this is a company that cares.
Thank you Pat and all of the employees that were involved in making this experience with your company go so well.
Larry S.
9/18/2019
product works great and has solved the problems i had. I have been telling everyone i know that if you need parts for your RV you must call Etrailer first you wont be sorry.
Donna was a great help getting our order for a front landing leg. Called on Monday am and order was received at our destination by Wednesday, today with a short time had the leg replaced. Great customer service!!!!!
Lc179014
9/13/2019
The leg is working great, knowledge staff, great products and fast shipping.
Several teeth were broken off or worn down, on my following leg landing gear, on our 2005 Keystone Challeger 5th wheel camper. our local dealer wanted $500+ to remove it, and reinstall a new one. After some on-line searching, I found this etrailer.com website. After looking at reviews, I followed their recommendation, and ordered the LC179014 leg and gear. I put in the order late afternoon on Wednesday, and it was on my doorstep Friday afternoon!!! I took the old leg out. The new leg would not "seat" correctly, and I was concerned I had made a mistake purchasing it. After doing some investigation, I found a bead of weld - on my camper - was preventing the leg from locking in place. I ground it off with my angle grinder, and the new leg fit PERFECTLY!! This new replacement weighs about 4 pounds more and is heavier constructed than the original. Plus the fact, there are grease zerks on the new, so it can be properly lubricated - unlike the factory one! In summary, THANK YOU e-trailer.com for a fantastic part!! You saved me about $400. I will be using your website again!! Ron
The Landing Gears have worked flawlessly for the last year. I have lubricated them once using Valvoline Multipurpose Grease #615.
Ron H.
5/5/2018
The 5th wheel landing gears are doing great!
Fast delivery, all parts necessary to connect crossbar, product came ahead of estimated delivery!
Levi
6/24/2021
After 1 year, it is holding strong!
We ordered the landing gear follow leg for our fifth wheel trailer free shipping was a plus. The leg arrived a 2 days earlier than expected another plus. The leg fit perfectly after we discovered that the original leg had been bent and twisted slightly from the previous owners. We were able to make a few adjustments and we installed the new leg with no other problems. All in all the job took a little longer because of the damage we had to fix but went smoothly after that. Will use e-trailer again. Thank you Michelle for your assistance, God bless
Ordered both legs, U-Tube said about and jour or so. Took 3.5 hours, but what a great learning experience. Goes quicker if your storage compartment is emptied before you start!
Frank M.
1/15/2019
Great
Frank M.
1/15/2019
All is good. Thanks for your help. We still have the 5th wheel, and all seems to be working fine. Fifth wheel put away for the winter, excited to continue our journeys.
First class product,very efficient ordering process and fast delivery. Most impressed.
Steve M.
3/8/2018
Excellent
If anybody need to know how to install a landing gear leg on a Grand Junction, feel free to contact me.
The parts came in good, the customer service was good. I wish they would have let me know that they were waiting on the small bracket but when I asked about it they were very up front about it. SO I am very pleased with everything.
This is a very good internet company to deal with.
Best investment for the camper we have gotten. It cools immediately and runs perfectly. Has different settings that allow the fan to run constantly which is great. I am a light sleeper and can't have the fan turn off and on. It's exactly what we needed & we haven't had any issues. No leaks, no down time.
This was a great purchase to replace the existing front end camper jacks. Replacement was very simple and operation is very smooth.
I am the original owner of a 2010 Montana Mountaineer 5th wheel. I replaced both the lead and follow landing gear. I studied the different landing gear available, and chose to try the cheaper items. These less expensive ones LC179014 and LC179013 were exactly the same as the old ones. Installation went smoothly, and they fit perfectly.
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Richard
3/15/2019
Still working properly, I’ve had no issues with it...