Landing Gear With Snap Pins for Keystone Springdale

Question

Question:

We have had one jack that locked up, managed to dismantle and found the screw had gone dry and the thread deformed. managed to clean up and and get it working .However, this is only tempory I will need to replace the jacks. would You be able to supply a pair with snap pins. I think Keystone use these LC178653 on the Cougars as well

asked by: Doug B

0

Expert Reply:

We do have replacement landing gear legs with snap pins, though the part you referenced is specific to the Keystone Montana, so you will need something different.

Assuming you have the standard 15-1/2" inside-to-inside distance between weld stops, and your leg has a 29-1/2" outer tube then you can use replacement legs from Lippert:

- Replacement 5th Wheel RV Landing Gear Lead Leg with Snap Pin # LC179013

- Replacement 5th Wheel RV Landing Gear Follow Leg with Snap Pin # LC179014

expert reply by: Kyle S

0

Answer 1

Yes you can just purchase the motor, in this case for your Lippert Model 1-065-041012-01, would be the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor #LC141893. This motor has a maximum load capacity of 5,000lbs and is rated for…

view full answer...

Answer 2

We do have the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor #LC141893 for your 2021 Keystone Springdale 5th wheel camper. This is the same model number 1-065-041012-01 that you have on your current landing gear motor. Nous…

view full answer...

Answer 3

The landing gear number you have provided appears to be a Venture number. Lippert landing gear components will work in place of Venture since they were bought out by Lippert some time ago. We do have lead leg #LC178653 and follower leg #LC178652…

view full answer...

Answer 4

The correct replacement for your 1-065-041012-01 motor is part #LC141893 from Lippert. Your original motor had a 7140 rpm speed. The Stromberg-Carlson #LG-196308 you specified has a 5430 rpm output, so it wouldn't be a good choice. You'll…

view full answer...

Answer 5

Before you go replacing your landing gear you should check a couple of things first to ensure that a full replacement is the way to go. There is a couple of reasons why a jack will blow fuses and struggle going up and down. One being weight of the…

view full answer...

Answer 6

If the bevel gears/gearbox for the dual-motor landing gear on your 2011 Keystone Laredo 266RL 5th wheel were badly worn or damaged you would most likely be able to hear it. These conditions typically cause a good bit of noise as the jacks try to…

view full answer...

Answer 7

Fuses blow because the circuit is getting overdrawn. If the motor of your landing gear is fine but you are still blowing fuses that would indicate that either you are overloading the jack and it is drawing too much amperage, or the next likely…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

Good news! I was able to go out to the warehouse and measure the etrailer landing gear #RVLG-8HDL for you. I found that the distance between the weld stops from the outside to outside is 17-1/2 inches and from the inside to the inside of the weld…

view full answer...