Replacement Lippert Landing Gear Follow Leg for 2009 Crossroads Cruiser

Question

Question:

I have a 2009 Crossroads Cruiser 5th wheel 31bh and the following landing gear has failed. I believe these units have Lippert frames. Can you point me to the correct part. The length of the outer leg is 29.5 inches and there is 17.5 and 15.5 inches respectively between the pieces that fit in the support brackets on the frame of the camper. Thanks

asked by: Kevin B

1

Helpful Expert Reply:

The Replacement 5th Wheel RV Landing Gear Follow Leg # LC179014 that you were looking at is exactly what you need to replace the follow leg for your Lippert landing gear system. Just like your existing leg this unit features an outer tube length of 29-1/2 inches, a distance of 15-1/2 inches between the bracket stops, and a distance of 17-1/2 inches when measuring outside to outside on the bracket stops.

I have attached a short video demonstration that you can also check out.

expert reply by: Chris R

1

Answer 1

It is very likely that you have the Venture landing gear with your Venture labeled motor. The gearbox is obviously working because the follow leg is working, so I recommend repairing the lead leg with #LG-146059 or replacing the lead leg with…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 5

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 9

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 10

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 11

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 12

The Replacement Amber Lens for MC32AB Trailer Lights #A32AB is a direct replacement for the SAE A P2 DOT 14 and would be what you'd need.

view full answer...

Replacement Lippert Landing Gear Follow Leg for 2009 Crossroads Cruiser

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching