Customers compare C45908 to these similar products
Products Featured in this Video
What's up everybody, it's AJ with etrailer.com. Today, we're checking out the Curt pintle hook. Now, this is going to be for 2 1/2 inch hitches, and it's got a two and 5/16 ball in there. It's going to go and attach to your lunette ring like we have set up here. You see how it lowers down around that ball. This part comes up on top, lashes it in place.… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
Yes, it will! The Curt Pintle Hook with 2-5/16" Ball item #C45908 will easily connect to your portable silo's lunette ring and allow you to safely tow it. This ball mount fits a 2-1/2" hitch receiver, includes a…
view full answer...When mounting a cast head coupler like Bulldog #BDA256C0317 to its mounting channel you will want to torque the mounting bolts to the specification indicated by the manufacturer in the instructions. The torque spec will vary from coupler to coupler.…
view full answer...Adjustable trailer couplers are not going to mount to your truck; they will attach to the frame of your trailer. Some of the adjustable couplers, such as the Bulldog Cast Head #BDA2563C0317 come with the mounting hardware to weld onto the frame of…
view full answer...There is pretty much a standard for channel mount couplers such as #DM12113-95. The channel width is usually 3 inches and the couplers are usually around 2-7/8 inches wide to fit in the 3 inch wide channel. Once torqued down there is no side to side…
view full answer...The Demco #DM12688-95 you've looked at would be a good choice. The 2 inch channel mount coupler is compatible with a 3 inch channel, and has bolt spacing of 2 inches on center. Demco is known for high quality products, you'll get years of…
view full answer...Because your F250 is not a long bed model, I would highly recommend you go with the Reese Elite Series w/ Slider, part #RP30144. Although the current trailer you are looking at has a v-type nose on it that might work okay with the #RP30921 and have…
view full answer...I spoke with my contact at Brophy and they stated you'll be fine using the Brophy Clamp On Camper Tie-Downs - Bed Mount - Black Powder Coated Steel - Qty 4 Item #HSWB as long as the railing on the back of your 2008 Chevy Silverado isn't over…
view full answer...According to CR Brophy, the camper tie down brackets you'd looked at, part #HSWB are specifically designed to fit the bed of a 2019 Ford F-250 and 350. There does indeed need to be 2 inches of available space under the lip of the truck bed side…
view full answer...I have a solution for you but we do not have a 2" square u bolt kit for a 3,500 lbs square axle that is 5 3/4" long. You will need to buy the u bolts and u bolt plates separately. The Square Trailer U-Bolt item #SP01-160 comes in a 2 pack,…
view full answer...Since the diameter size of the posts on this u-bolt is 9/16-inch you can ideally use a 9/16-inch or 5/8-inch bit (or even a 1/2-inch bit if you have the room to move the drill around enough to ream the hole to the required size). In either case you…
view full answer...There is! To replace the standard pin and clip on the Curt QuickPin No Latch A-Frame Trailer Coupler #C84DR Curt actually recommend the Hitch Lock #C23025 which is what I recommend going with!
view full answer...It sounds like you are looking for a 2-Tang clevis hitch for the 3" receiver on your vehicle. Since there is no 3" option I recommend the Gen-Y 2-Tang Clevis for 2-1/2" Hitch Receivers - 21,000 lbs #325-GH-069. Along with this clevis…
view full answer...