Trailer Hitch Receiver Sizes

Trailer hitch receivers are available in 4 main sizes: 1-1/4", 2", 2-1/2", and 3". These numbers refer to the width of the receiver openings.

Below, we'll go over the standard hitch receiver sizes and their capabilities. You can also read more about trailer hitch weight capacities in our article, How to Choose the Right Trailer Hitch Class.

NOTE:

To determine the size of your trailer hitch, simply measure the height and width of its opening. The two most common sizes of trailer hitch receivers are 1-1/4" and 2".

Draw-Tite 1-1/4 Inch Trailer Hitch Receiver - Jeep Wrangler JL

Class I Curt Trailer Hitch On Honda Civic

1-1/4" - Class I and Class II Hitches

Class I and Class II trailer hitches typically have a 1-1/4" x 1-1/4" receiver opening. These hitches are most often found on passenger cars and smaller SUVs. There are a few Class II hitches that have 2" x 2" receiver openings, but this is not common.

Typical weight ratings for Class I trailer hitches:

Maximum gross trailer weight: 1,000 lbs to 2,000 lbs
Maximum tongue weight: 100 lbs to 200 lbs

Typical weight ratings for Class II trailer hitches:

Maximum gross trailer weight: 2,000 lbs to 3,500 lbs
Maximum tongue weight: 200 lbs to 525 lbs

Why won't my 1-1/4" accessories fit in my 1-1/4" receiver opening?

You might think that any hitch accessory with a 1-1/4" x 1-1/4" shank would work in either a Class I or Class II trailer hitch, but this is not the case.

Many hitch accessories are designed to maximize the weight carrying capabilities of the trailer hitches they're used with. To keep you from overloading your Class I hitch, Class II hitch accessories—such as drawbars, bike racks, and cargo carriers—will not fit into Class I hitches.

Manufacturers accomplish this by placing a stopper in the back of Class I hitch receivers so that drawbars and accessory shanks can only slide into the trailer hitch opening up to that point. On hitch accessories designed for Class II trailer hitches, the shank that slides into the hitch opening is longer. When this longer shank slides into a Class I hitch, it will hit the stopper, preventing the pin hole on the hitch from lining up with the pin hole on the accessory.

Class I hitch accessories—drawbars, bike racks and cargo carriers— are designed to fit into your Class I hitch perfectly. These accessories will work in Class II trailer hitches as well. Decorative hitch covers listed for the 1-1/4" hitch size will also work in both Class I and Class II trailer hitches.

Valley 2-Inch Trailer Hitch Receiver - Dodge Dakota pickup

Valley 2-Inch Trailer Hitch Receiver - Jeep Grand Cherokee

2" - Class III and Class IV Hitches

2" x 2" trailer hitch receivers are the most common type. Most 2" hitches are either Class III or Class IV. These hitches are typically found on pickup trucks, SUVs, and some full-size sedans. Most trucks and SUVs that come factory-equipped with a trailer hitch have a 2" receiver.

Many 2" hitches are also rated for use with weight-distribution systems. By using a weight-distribution system while towing, you can maximize the full weight carrying potential of your hitch.

Typical weight ratings for Class III trailer hitches:

Maximum gross trailer weight: 3,500 lbs to 8,000 lbs
Maximum tongue weight: 300 lbs to 800 lbs

Typical weight ratings for Class IV trailer hitches:

Maximum gross trailer weight: 5,000 lbs to 12,000 lbs
Maximum tongue weight: 500 lbs to 1,200 lbs

Heavy-Duty 2" Trailer Hitches

Some 2" trailer hitch receivers are categorized as Class V hitches because of their increased weight capacity. The construction of these hitches allows them to carry more weight than a typical 2" hitch, making them perfect for heavy-duty towing applications.

For instance, Draw-Tite makes a Class V hitch with a cast center section so that it not only has a higher overall weight capacity, but it also has the highest tongue weight rating possible. The reinforced center sections on these hitches enable them to handle far more than just 10 percent of the gross trailer weight, which is a typical tongue weight capacity.

Factory 2" Trailer Hitch Variances

Of those vehicles that come from the factory with 2" hitches, some have slight variances in the construction of the hitch. For example, the 2" hitch receivers on Toyota Tundra pickups are built of thick tubing. As a result, some flush-mounted trailer hitch locks that designed for typical 2" hitches will not fit because their spans are not long enough.

TorkLift Class V 2-1/2-Inch Trailer Hitch Receiver

2-1/2" - Class V Hitches

Trailer hitch receivers that measure 2-1/2" are designed for use on heavy-duty trucks that can handle extreme capacities. Hitches of this size are classified as Class V hitches. Some trucks come with factory 2-1/2" receivers, but you can also purchase these hitches as aftermarket additions.

Hitch accessories designed for 2" trailer hitches will work with 2-1/2" hitches with the use of a specialized hitch adapter. Most Class V hitches are rated for use with weight-distribution systems so that you can maximize their weight-carrying ability.

Typical weight ratings for Class V 2-1/2" trailer hitches:

Maximum gross trailer weight: 10,000 lbs to 20,000 lbs
Maximum tongue weight: 1,000 lbs to 2,000 lbs

Curt HD Class V Ball Mount for 3-Inch Hitches

3" - Class V Hitches

These heavy-duty Class V hitches are starting to appear on newer-model trucks straight from the factory. You can also purchase 3" hitches as aftermarket additions. These hitches must typically be welded to the C-channel frame of your vehicle and are ideal for use with dump trailers, flatbeds, etc. Unlike most other hitches, these are not vehicle specific.

Adapters for 3" hitches are available to adapt the 3" opening to a more standard 2" or 2-1/2" opening. You can also find weight distribution systems compatible with 3" hitches, though this hitch size is less common than other types, so your options will be more limited.

Typical weight ratings for Class V 3" trailer hitches:

Maximum gross trailer weight: 20,000 lbs to 25,000 lbs
Maximum tongue weight: 3,000 lbs to 4,000 lbs

Reese Class I Trailer Hitch Receiver with Rectangular Opening

Uncommonly Sized Trailer Hitches

Rectangular hitch receivers are the least common type. Hidden Hitch and Reese no longer manufacturer these receivers, which were previously Class I and Class II hitches designed for smaller cars. There are no hitch accessories available to slide directly into a rectangular hitch opening.

Save or Share This Idea

Related Products

Shop Ball Mounts

Shop Wiring

Shop Weight Distribution

Updated On: 3/12/2019

Roy K.

9/18/2023

I have 1 1/4 opening but my bike rack is 2 inch how to I get an adapter

Mike L.

9/19/2023

@RoyK The best practice would be to use a bike rack that's been designed to work with your existing 1-1/4 inch receiver. If that isn't feasible, you can use an adapter like # e43YR. However, using the adapter will reduce the tongue weight capacity of your hitch by half, so you'll want to avoid that if at all possible.

Larry B.

10/28/2022

2014 dodge diesel 2500 have a class v receiver, travel trailer weights 12300 lbs an a tongue weight 1840 lbs do I need to up grade to bigger receiver?

David B.

10/28/2022

Nope I think you are good Larry! I would say if you have a factory hitch to check the tongue weight limit, it will be on the hitch or owner's manual; sometimes it is in the door plate/sticker. If it is an aftermarket the label should be on the unit itself. As you can see in the FAQ the weight caps for a class 5 are the highest possible for this style of hitch so you really don't need to upgrade because you kinda can't.

Tommy K.

8/31/2022

I have a cargo tray (2") that I used for my RV. Now I want to use it on my Toyota Highlander that has a 2-1/2" hitch. I need an accessory that will have a 2" on one end and a 2-1/2" on the other end. Where can I get this?

David B.

9/2/2022

Is this what you are needing Tommy? Trailer Hitch Receiver Reducer Sleeve - 2-1/2" to 2" # e26YR.

David T.

7/18/2022

I have an Infinity Q60 Sport. Not really meant to have a hitch. However, sometimes I want to strike out solo instead of going with friends with racks. Any reasonable options for a class II 1 1/4 hitch? Prefer no strapon racks on back or roof.

David B.

7/25/2022

What year is your Q60?

Hamidm

2/5/2022

I bought the Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4" for my 2010 Volvo S80 (installed). The e-Bike rack that I need to attach has a 2" receiver to haul a 75lbs bike. Is this adapter the way to go? MaxxTow Trailer Hitch Receiver Adapter 1-1/4" (Class I or II) to 2" Hitch - 11" Long. What do you recommend?

Les D.

2/7/2022

@Hamidn Your Class-2 hitch receiver has around a 350 pound tongue weight rating, but this will not be the weak link. Your Volvo body has a 330 pound tongue weight capacity. However, by adding an adapter you cut that in half, or 165 pounds. As long as you do not exceed the 165 pound capacity, using the MaxxTow # MT70032 adapter would be ok.

Hamidm

2/7/2022

@LesD I'm sitting at 120lbs, so I should be fine, thanks! (70lbs bike) + (45lbs bike rack) + (5lbs hitch adapter) This is a great forum, reading the response to the other questions made me more informed about hitch classes, tongue weight and lots of other stuff that I was clueless about. Thanks Again! HamidM

Les D.

2/8/2022

@Hamidm Glad we could be helpful.

Show All (25) Replies

Hide Replies

Explore Expert Info

on Trailer Hitch

Videos

for Trailer Hitch

Help Articles

for Trailer Hitch

Expert Answers

for Trailer Hitch

Choosing the Right Trailer Wiring

Roadmaster Smart Diode 7-Wire to 6-Wire Wiring Kit Installation - 2023 Jeep Wrangler Unlimited

Trailer Hitch Installation - 2013 Honda Civic - Curt

Review of Maxtrax Tow Straps and Recovery Straps - Recovery Strap - MA53PR

Lock N Roll 3-Position Channel Articulating Hitch Review

RockyMounts HighNoon FC Solo 1 Bike Rack Review

SumoSprings Trailer Helper Springs Installation - 2018 Forest River Cedar Creek Champagne Fifth Whee

Curt T-Connector Vehicle Wiring Harness Installation - 2013 Honda Civic

Rhino Rack Roof Rack Review - 2015 Ford Edge

RockyMounts Hitch Bike Racks Review - 2021 Honda CR-V

Roadmaster Direct-Connect Base Plate Kit Installation - 2023 Jeep Wrangler Unlimited

Choosing the Right Brake Controller

How to Choose the Right Trailer Hitch Class

How to Measure for Trailer Hitch Drop

Hitch Adapters and Extenders

What Do I Need To Tow A Trailer?

My Trailer Hitch Doesn't Fit

The 5 Best Trailer Drop Hitches You Can Buy

Trailer Wiring Diagrams

Ball Mount Basics: Weight Capacity, Class, and Size

Brake Controller 7- and 4-Way Installation Kit (ETBC7)

Rooftop Cargo Carriers

5 Things to Know About Weight Distribution Hitches

Determining Trailer Tongue Weight

What is the Difference Between a Class II and a Class III Hitch?

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Yes, it will! The etrailer Hitch item #e98854 has a 4,000 lbs towing capacity and is confirmed to fit your 2014 Dodge Grand Caravan SE. This hitch is custom fit and bolts to your Dodge with included hardware. I have linked an installation video…

view full answer...

Can The SumoSprings Trailer Helper Springs #SS26MV Be Used On a 2019 Grand Design Solitude?

The brackets on the SumoSprings Trailer Helper Springs #SS26MV are 1-1/2" wide so they will fit evenly across the humps on your spring pads. I do not recommend cutting down the spring and you will be able to use these even with only having…

view full answer...

The Torflex Lift Kit item #K71-707-01 is the correct kit for a #10 Dexter torsion axle and you won't need to drill any new holes into the spacers. I have attached a couple of pictures below so you can see how they look once installed. I have…

view full answer...

Is Torflex Lift Kit K71-723-01 Only Lift Kit Size that Fits This Axle

The Torflex lift kit part #K71-723-01 is the only size lift we have that fits this axle configuration. There isn't a 2-5/8 inch lift available that is similar to it.

view full answer...

What Size Trailer Hitch Receiver Opening Comes On a 2024 Chevrolet Silverado 3500?

Your 2024 Chevrolet Silverado 3500 will come with a 2-1/2" trailer hitch receiver. If your truck did not come with a reducer for a 2" receiver we do have the B&W #BWRHXA2182 if you need to use your 2" ball mount or…

view full answer...

We have exactly what you need. For flat tow wiring for a 2024 Jeep Wrangler I recommend the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit #RM-15267. This kit includes the coiled cable to connect to the RV 7-way, as well as a 6-pin round…

view full answer...

Unfortunately no, the Phoenix USA QuickTrim Hub Cover for Trailer Wheels #PXQT550CH4 is only available in chrome. We do have the Phoenix USA QuickTrim Hub Cover for Trailer Wheels #PXQT545BHS which is identical but it only works with a 5 on 4 1/2…

view full answer...

Are there Shorter Crossbars Available for the Malone MicroSport Trailer

Malone does offer the 2nd Tier Load Bar System for Malone MicroSport Trailer #MPG474 which measures 50" long and would work with your MicroSport trailer, however these bars are only rated for 100 lbs so you'd be loosing around 400…

view full answer...

Will Curt Hitch Cargo Carrier #C18151 Fit On 2005 Jeep Grand Cherokee

To know if the Curt Hitch Cargo Carrier, #C18151, will fold up on your 2005 Jeep Grand Cherokee and not have any clearance problems, you will need to make a measurement on your vehicle. You will need to measure from the center of the hitch pin hole…

view full answer...

Replacement 7-Way for 2018 Ford F-150 and Airstream to Provide Tight Connection

For a standard replacement 7-way for your 2018 Ford F-150 we have the Mighty Cord part #A10-7072VP which would easily install and give you a connector that would provide a solid connection. To do a replacement 7-way on your Airstream you could go…

view full answer...

Kuat Sherpa 2.0 vs. Kuat Transfer V2 for 2 Inch Trailer Hitch

I can help you choose between the Kuat Sherpa 2.0 and Kuat Transfer V2, as both are really nice bike racks. Let me start off, since you mentioned 3-bike rack, if that's what you were after you would need the Kuat Transfer V2 Bike Rack for 3…

view full answer...