Customers compare C87CR to these similar products
Products Featured in this Video
Hello, everybody, this is Jeff at etrailer.com. Let's just take a look at the Curt 44 inch wide class five universal weld-on hitch with the two and a half inch receiver and the mounting brackets. Now, this is a universal weld-on hitch. It's designed for use on service body trucks and utility body trucks, and as you can see, this hitch comes in a three piece design, has the main body tube right… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
I do have an option for you but there aren't any custom fit trailer hitch options for a 2006 Thomas School Bus. That said, we do still have universal options which can be installed either via welding or cutting/drilling. For this, I recommend the…
view full answer...The trailer hitches we have available for the 2014 GMC Savana Van are designed to fit the full size van model. To see if these will fit your Cutaway version, I just recommend taking a couple measurements on the vehicle's frame. The trailer hitch…
view full answer...There is a way for you to add a trailer hitch to your 2002 Thomas Saf-T-Liner bus although there are none mounted vertically onto the frame, they will use brackets to mount to the frame which can be bolted or welded on. What you need is the Draw-Tite…
view full answer...The Curt Class V Universal Weld-on Hitch part #C37CR is offered with longer brackets, part #C87CR. The brackets are a bit taller than you were looking for but could be cut down easily.
view full answer...The Draw-Tite Class III hitch you mentioned, part #41946 will fit a 2005 Chevy Express, but I couldn't say if it'll fit a motorhome on a cutaway van chassis. Usually the rear bumper structure at the rear of a motorhome is much different that…
view full answer...I went to the warehouse and measured the Curt Trailer Hitch Receiver, part #C15703. I have attached a photo of the trailer hitch and have noted the dimensions you can check out. This is a Class V trailer hitch and it has a 2-1/2 inch receiver…
view full answer...The Draw-Tite Trailer Hitch Receiver #DT45516 has a receiver drop of 5-1/2" from the frame. The width of the rear most bolt holes are 30-13/16" from center of hole to center of hole. I have included these measurements on the picture below.
view full answer...For a 2004 Ford E-350 Cab and Chassis the Draw-Tite #41906 is a custom fit, but you will need to make sure that the bolt holes are 38-5/8 inches from frame to frame in order for it to fit your particular model. While this hitch is a custom fit for…
view full answer...We do have a couple Class V hitch options available for your 2020 F53 and I have 3 options listed below. These will all be rated to 16,000 pounds towing and 1,600 pounds of tongue weight and use a 2" receiver opening. They will all also fit a…
view full answer...There are a few options for your 2000 International 4900 Truck, but there is not a custom fit receiver available. The Super Titan 4000 Weld-On Trailer Hitch with 3" Receiver Opening, 25,000 lbs. #38124 could work but requires the frame on your…
view full answer...While we have a potential option for you, the hitches that fit a 2000 Chevy Express van have mounting holes 40 inches apart, and additionally the manufacturers expressly state they do not fit the cutaway models, so you will need one of the universal…
view full answer...The only option we have for a hitch for your school bus with a 34 inch frame is a weld on hitch: - Class V Universal Weld-on Receiver Hitch and Brackets with 3" Drop #15901 This is for frames up to 44 inches wide and gives you the drop you need…
view full answer...