Dimensions Of Curt Class V Trailer Hitch Receiver for 2006 Chevrolet Silverado

Question

Question:

what are the dimensions on the #c15703 I have a 2006 chevy 3500 42 inch frame utility bed with a Tommy Lift.

asked by: David

0

Expert Reply:

I went to the warehouse and measured the Curt Trailer Hitch Receiver, part # C15703.

I have attached a photo of the trailer hitch and have noted the dimensions you can check out. This is a Class V trailer hitch and it has a 2-1/2 inch receiver opening.

expert reply by: Jeffrey L

0

click to enlarge

Answer 1

We haven't had the chance to install the Curt Class V Trailer Hitch Receiver #C15703 on the 2008 Chevy Silverado 2500 so I don't have exactly how far beneath the bumper the receiver will sit, however I did go out to our warehouse to take a…

view full answer...

Answer 2

For a 2002 GMC Sierra 2500 HD, you'd want to use the Curt Class V hitch, part #C15703. I checked with Curt, and found that the drop of this hitch (measurement from the mounting flange to the top of the crossbar) is 5.13 inches, as shown in the…

view full answer...

Answer 3

The trailer hitches we have available for the 2014 GMC Savana Van are designed to fit the full size van model. To see if these will fit your Cutaway version, I just recommend taking a couple measurements on the vehicle's frame. The trailer hitch…

view full answer...

Answer 4

The main difference between the #RAS3611 and #RAS3611-HD is the capacity. The regular system has a 2,000 lb weight capacity while the HD system is 3,000 lbs. I would choose the HD system for the additional support. The lowest tension setting on the…

view full answer...

Answer 5

Curt does not have that measurement available, but you can determine this for yourself by taking some measurements from the underside of your truck. Using the diagram I edited for you, locate the weldnut that would serve as the rear-most attachment…

view full answer...

Answer 6

The Draw-Tite Class III hitch you mentioned, part #41946 will fit a 2005 Chevy Express, but I couldn't say if it'll fit a motorhome on a cutaway van chassis. Usually the rear bumper structure at the rear of a motorhome is much different that…

view full answer...

Answer 7

Curt Trailer Hitch Receiver #C15703 hangs pretty low on a 2005 Chevy Silverado 2500. From the bottom of the bumper to the top of the hitch receiver it is approximately 4 inches. I have included a picture showing the gap. A similar hitch, #C15302,…

view full answer...

Answer 8

I had our warehouse measure the Curt Trailer Hitch Receiver #C15703 you were looking at, and has an overall width of 40-5/8", overall length of 29". The distance between the vertical mounting holes is 14-1/2" center to center, and the…

view full answer...

Answer 9

I checked with Torklift and they informed me that their hitch part #TLC1205-30 has the following dimensions: The center to center hole is approx 39.5" total width is about 41.5" side plate height is 9.75"

view full answer...

Answer 10

Yes, the hitch lock part #C23519 that you referenced is designed for use with 2-1/2 inch hitches like what a Class V hitch is so it would work great with one.

view full answer...

Answer 11

For your 2003 GMC Sierra 2500HD with the 6.0L V8 engine, I highly recommend the Derale Series 8000 Plate-Fin Transmission Cooler Kit part #D13504. This 8000 series cooler measures 11" wide x 12" tall x 7/8" deep which will be a good…

view full answer...

Answer 12

We offer Class V hitches in both 2-inch and 2-1/2-inch sizes for your 2009 Chevrolet Silverado 2500. All are shown on the linked page. Draw-Tite's 2-inch hitch #41944 is a no-drill install since it bolts up to the bumper bracket the same way as…

view full answer...

Dimensions Of Curt Class V Trailer Hitch Receiver for 2006 Chevrolet Silverado

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching