Pollak Universal-Design Rocker Switch - SPST - On-Off - 12 Volt - 20 Amp - Black

See what our Experts say about this Pollak Accessories and Parts

• Parts to Connect Trailer Lights to 12V Trailer Battery
  It is easy to wire your trailer battery to your trailer's lights if that is how you prefer to run them. You might want to add a Solar Charger or two, like # PTW2997, to keep a continuous charge going to the trailer battery. This charger will naturally deliver a varying power output to your battery depending on the level of sunlight hitting the panel so using two in parallel connection to the battery will really help maintain its charge. If you need a 12V power switch to control the lights...
  view full answer...
• Three Way Switch for RV Lights
  I know exactly what you are looking for. We have two switches, one in white one in black, that will do just what you are asking. These switches also have a dimmer feature which you don't have to use. They are the, RV LED Light Side-Slide Dimmer Switch - White item # 37205-12325 RV LED Light Side-Slide Dimmer Switch - Black item # 37205-12315 I have attached a diagram and a review video.
  view full answer...
  
• How To Power Furrion LED Marker Light Camera When Trailer Isn't Connected To Tow Vehicle
  If you wire the camera wire of the LED Marker Light RV Side Cameras w/ Night Vision for Furrion Vision S Systems # FCE48TASL you were looking at to the running light circuit then the running light will be on any time the camera is on as that is where the power is coming from. Now since you are wanting the camera to work even when the trailer is unplugged I recommend wiring the running light wire from the camera to the factory running light wire, and then running a new wire using # 16-1-1...
  view full answer...
• Power Options for Utility Lighting on Utility Trailer
  There are a few different ways that you can get power to the LED utility lights on your trailer. The first would be to have a battery directly on your trailer that you could draw power from. This would be the easiest way to get power to your lights. To charge the battery you would need to use a charger like part # CTEK56353 when you have access to a standard wall outlet. One of the perks to using this setup is that you can disconnect your tow vehicle and still use the lights when you need...
  view full answer...
• How to Turn Off Back-Up Alarm of Curt C57100 When Not Towing
  Once the Curt # C57100 is installed, the alarm will sound every time you put the transmission in reverse, regardless of whether or not you're towing at the time. The only way I can think of to defeat the alarm for when you're not towing would be to install a switch like # PK34308 inline on the wire feeding the reverse lamp circuit to the # C57100. You'd need to peel back the tape or wire loom that covers the factory wiring harness the C57100 plugs into. Use a circuit tester like # PTW2993...
  view full answer...
  
• Powering Furrion Vision S With 5 Inch Monitor When Not Plugged in to Truck
  While you wouldn't be able to use shore power, there is a way to use the Furrion Vision S Wireless RV Observation Camera System w/ Side Marker Light Cameras - 5" Screen # FCE48TASL-05 in your camper, but it will require some added wiring. What you can do is take the wiring from the camera that is connected to the running lights, and connect it to rocker switch # PK34308, then from the switch directly to the battery on your trailer. You will also need a 12 volt outlet # 37215105 with mounting...
  view full answer...
• Running Wires For Hopkins Backup Camera To Mount On Front Of Vehicle
  In order for you to be able to use the Hopkins Smart Hitch Backup Camera, part # HM50002 as a camera and monitor, you will need to cut the plug off the end and hard wire the system. If you are going to use it for the front I recommend running the red wire to the battery and use a switch. You will need additional wiring like part # DW07550-1 to reach the switch inside of the vehicle. This is sold by the foot. You will also need to secure the white ground wire to a clean bare metal surface. For...
  view full answer...
• Small Single-Pole Rocker Switch
  I am not 100 percent sure what size you need, but a small option for a single-pole rocker switch is the Pollak Universal-Design Rocker Switch # PK34308. This switch is less than an inch wide (15/16") and just under 1-3/4" tall (1-11/16"). The Single Rocker Switch # 37212525 is another option and is just 1-1/8" tall x 1/2" wide. I have added a link to our entire selection of rocker switches for you to check out as well.
  view full answer...
  
• How to Wire Furrion Vision S Observation Camera for Better Signal Transmission
  My tech contact at Furrion has seen connectivity issues like you're having with your Furrion Vision S observation camera system # FOS43TASF. He said that late model vehicles and/or trailers that have highly-efficient LED lights may not use wiring heavy enough to fully power the transmitter on the camera. The fix for this is to use a direct battery connection and a manual switch like # PK34308 for delivering operating power to the camera, rather than the clearance light circuit on the trailer.
  view full answer...
• How to Power Enclosed Trailer Lights Off of 12V Battery
  I can tell you exactly what you'll need to power your enclosed trailer's lights off of an independent 12V battery, though there isn't an adapter. You first need to mount the battery with a battery box for 12V batteries like # TLA7708R, and then use junction box # 38656 to tap into your trailer's 7-way. You will also need ring terminals # 44-5310A, and wire # 12-1-1 to run to each light, and to turn the lights on, a light switch such as the Pollak rocker switch # PK34308 or toggle switch...
  view full answer...
• Troubleshooting Lost Power on 7-Way Trailer Connector on 2018 Ram 1500
  I'd start by making sure that your 7 way didn't get disconnected from the US car connector it's plugged into. If a fuse was blown, it would normally only effect the circuit that it's tied to, so I don't believe that would be the cause of your issue. For everything to completely shut off would lead me to believe that something has either become loose or disconnected completely. If that isn't the case, it might be possible that something overloaded the 7 way connector and fried it. You...
  view full answer...
• How to Power Interior Lights on Enclosed Trailer
  The best way to power interior lights in your enclosed trailer is with an independent 12 volt battery mounted on the trailer. To do this, mount the battery with Battery Box # TLA7708R and use junction box # 38656 to tap into your 7-way so the battery gets a maintenance charge when you are hooked up to the 7-way. Hooking up the junction box will require ring terminals # 44-5310A, and wire # 12-1-1 to run to each light, and you can use rocker switch # PK34308 to turn them on and off. Your...
  view full answer...
• What Will Pollak Rocker Switch Fit
  It depends on how big the switches are, as we have no way of knowing the dimensions of your control panel. So you'll simply need to measure, and if the opening is 0.830" wide x 1.450" tall and 0.093", 0.125", or 0.187" thick you can use the Pollak Universal-Design Rocker Switch # PK34308.
  view full answer...
  
• Wiring Exterior Trailer Lights to be Powered by Reverse Circuit and On Board Battery
  In order to wire your exterior hi-mount trailer lights so that they are powered by the reverse light circuit on your Ram but can also be powered by the on board battery, you will just need to use a diode like the Roadmaster # RM-790. The output side of the diode will go to your exterior LED lights, while the input side will go to the center pin on your 7-Way and also to your on board battery via a switch like # PK34308. I also recommend adding a circuit breaker like # 9506P before the battery....
  view full answer...
  
• Best Way to Power Lights in Enclosed Trailer
  Ok, we can give you some guidance on this, and the best way to power up interior lights in your enclosed trailer is with an independent 12 volt battery mounted directly on the trailer. To do this, mount the battery with Battery Box # TLA7708R and use a junction box like # 38656 to tap into your 7-way so the battery gets a maintenance charge when you are hooked up to the 7-way. If you need to hook up your junction box it will require ring terminals # 44-5310A, and 12 gauge wire # 12-1-1...
  view full answer...
• Parts Needed to Add Battery to Horse Trailer to Power Trailer Lights
  We don't have a specific wiring diagram to add a battery like this but the process isn't overly complicated. You will need a battery box like # 329-HM318BKS along with wire # 12-1-1 to run to each light and a switch # PK34308 to turn the lights on an off unless they have one built in. You can run the power to the lights directly from the battery or add an in-line fuse with # SWC9539. I would also add a junction box # 38656 and tap into the 7-way so you can get a maintenance charge on...
  view full answer...
• How to Add Power for Lights on Enclosed Trailer When Not Connected to Tow Vehicle
  The battery you already have for your trailer brakes is more than likely a breakaway battery. The brakes on your trailer are going to get power from your vehicle through your 7-way connection. In order to power your trailer lights when the tow vehicle is not connected you will need a 12V battery like the # BRW34FR. From there I recommend running a charge line from your vehicle using # 12-1-1. It would also be a good idea to install a switch like the # PK34308 so you can control the power...
  view full answer...
• Powering Interior Lights of Enclosed Trailer With 12 Volt Battery
  There is a simpler way than a generator, as this would be difficult, and most generators that have a 12 volt outlet require that only to be used for battery charging. So I recommend a standalone battery on your enclosed trailer, and I'm sure you can find somebody to do it for you, yes. You'll need to utilize local resources though to find someone such as a local handyman possibly or some other individual comfortable with wiring. What you'll do is use a 12 volt battery mounted on the trailer....
  view full answer...
• Recommended 12V Switches To Replace Interior Light Switches
  i have attached a link to the switched we offer that may work for your light switch. For a single pole/single throw switch for 12V DC systems I recommend part # PK34308. If you prefer a switch with a Red pilot light I recommend part # PK34360. These are rocker design switches. If you want a toggle switch for your lights I recommend part # PK34571.
  view full answer...

Do you have a question about this Accessories and Part?