T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
(217 reviews)
Price: $50.19
In Stock
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
Item # 118415
Retail:$68.39
Our Price: $50.19
You Save: 27%
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (217)
- Q & A (0)
- Photos
Tekonsha Custom Fit Vehicle Wiring - 118415
- Custom Fit
- Trailer Hitch Wiring
- 4 Flat
- Converter
- Tekonsha
Quickly and easily install a 4-way trailer connector on your Kia Forte with this custom wiring harness. T-One connector plugs directly into existing wiring - no cutting, splicing or tapping required. Circuit-protected converter guards against shorts.
Features:
- Provides a 4-way flat trailer connector at the back of your vehicle to power your trailer's signal lights
- Compatible with 5-pole, 6-pole and 7-pole adapters (sold separately)
- Connects quickly and easily - no cutting or splicing of wires
- Locate connection points in rear cargo area
- Plug in T-connector
- Includes circuit-protected tail light converter to ensure that your vehicle's wiring matches that of your trailer
- Provides protection against electrical shorts and overloads
- Constructed of 16-gauge bonded wire
- Comes with dust cap for 4-way flat connector
Specs:
- Maximum amperage:
- Stop/turn lights: 2.1 amps per circuit
- Tail lights: 5 amps per circuit
- 1-Year limited warranty
Installation
This custom-fit T-One connector plugs into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side interior trim panels in your rear cargo area.
Once installation is complete, the 4-way flat connector will be stowed within your trunk or rear cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
Circuit-Protected Tail Light Converter
A tail light converter is built into this T-One connector. Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of your trailer. The tail light converter combines the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
This converter safeguards itself and your vehicle against possible electrical shorts and overloads with integrated short circuit protection. Just install the connector as indicated and rest assured that the wiring system of your vehicle will remain feedback-free.
118415 Tow Ready T-1 T-Connector - 4 Wire
Installation Details
This Product Fits The Following Vehicles
- 2010 - 2013 Kia Forte Sedan
- 2007 - 2012 Hyundai Santa Fe
- 2007 - 2012 Hyundai Santa Fe without factory tow package
California residents: click here
Customer Satisfaction Score:
95% were satisfied with this product
5% of customers were not satisfied
- Wrong item was ordered
- Too difficult to install
- Product did not meet expectations
Customer Reviews
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector - 118415
Average Customer Rating: 4.9 out of 5 stars (217 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring - no cutting, splicing or tapping required. Circuit-protected converter guards against shorts.by: Elizabeth 11/18/2023
Very happy customer! My order arrived a day earlier than expected & my new trailer hitch and wire harness were installed with no issues and everything works perfectly!
by: John 10/06/2023
Everything was excellent looking on website, from calling saying what I needed, had in stock , free shipping over 99 dollars, was delivered in 3days . Very thing was awesome.. I recommend this company for anybody that needs trailer hitches or more.
by: David 06/20/2023
The instructions in the box are not very good. View the install video on the website instead. Has all you need. Installation is easy. Took me less than a half hour. Fit of the connectors is perfect. Trailer lights worked first time.
by: Bradley03/07/2018
Product works as described; didn’t take too long to install. Some removal of panels are required, basic tools needed to install. Very pleased with how it works and would buy from etrailer again.
by: Paul G.07/15/2017
2008 Hyundai Santa Fe
This was a breeze! Went exactly as the online video said. The threshold actually came out with the storage tray which helped me skip a step. I did do one thing differently and that is I took a 1 1/4" paddle bit and drilled a hole in the left side of the storage tray. This allowed me to thread trailer wire in for storage without it having to go in-between.
by: Dewayne 10/23/2022
Excellent product. Fit and working exactly as it's supposed to. Very detailed directions.
by: Linda 02/08/2024
2008 Hyundai Santa Fe
It was as advertised and was easy to in stall
by: Christian 08/31/2023
Great wiring kit! Easy to install
by: David D.04/01/2011
I found the hardest part of that was removing the plastic trim and then getting the carpet back under the trunk seal
The harness went together really quick.
by: Johnny11/28/2020
2007 Hyundai Santa Fe
After trying unsuccessfully for 2 days to fix an old U-Haul installed wiring harness on my 2007 Hyundai Santa Fe (located under the vehicle's left rear quarter panel), I did a little research online and found etrailer.com, and ordered the T-One Vehicle Wiring Harness Item #118415 on Nov. 21, and received it on Nov. 27th. The price was less than half what I was going to have to pay to order a new U-Haul version. This wiring harness was everything the online description said it was - specific to my vehicle and inline connectors that require "no splicing". The instructions had actual pictures of a similar vehicle and showed where to access the vehicle's left and right rear wiring connections. Start to finish the installation took about 2.5-3 hrs, but the majority of this time was spent removing the SUV's rear cargo compartment threshold, storage trays and access panels (so that the wiring was below those and not exposed), running the trailer connector externally to the hitch instead of just leaving it exposed in the cargo area, and removing the old U-Haul wiring box and splicers. Connections were made flawlessly. The only thing I had to do was drill a hole to connect the white ground wire to the frame of the vehicle with the self-tapping screw provided. The relay box was to be attached with "provided" double-sided tape behind the driver's side side panel. The tape was missing but I had some so it was no big deal. Once wiring connections were made and the ground wire secured to frame, I tested the 4-pole flat connector with a tester I had and everything worked perfectly. I then replaced the cargo storage trays and threshold, and snapped all the panels back in place.
I highly recommend this product. The cost was excellent, the product well designed, and the written instructions were specific to my vehicle and had pictures of the same make/model of vehicle as well. The installation went well, and was certainly easier than crawling around under the vehicle trying to splice into the vehicle lights wiring.
One additional step I took, was to order the 4-Pole Mounting Bracket Item #18144, and to snake the harness 4-Pole Flat Trailer Connector through the cargo compartment/bumper assembly and secure it to the towing hitch frame for easy access when hooking up my boat trailer. It even works with the connector's attached cover that protects the connector from weather, etc. I also purchased the Loctite Di-electric grease Item #LT37534 and applied to the connector terminals with a Q-Tip for added protection and ease of connection of trailer 4-flat connector.
Johnny A.
11/28/2021
This product has worked flawlessly for the last year. My boat trailer lights work every time, and I am completely pleased with the products I purchased. I highly recommend them to anyone who is needs to run a trailer wiring harness to their vehicle. Instructions and pictures were specific to my exact vehicle, make model year.
by: Daniel03/20/2023
2007 Hyundai Santa Fe
Haven't installed yet, but noticed the double-sided tape referenced in the install instructions is not included in the box.
by: Cory B04/22/2014
Hyundai Santa Fe
I ordered a class 3 hitch and wiring kit for my Hyundai Santa Fe. The process of selecting the right hitch and wiring was extremely easy on the site, and the order was received quickly via regular shipping.
Using the videos on the site as a reference, both the hitch and wiring were installed in less than hour total.
The service and information available at eTrailer was excellent. I am very happy with my purchase.
Cory B.
5/5/2015
Thanks for the follow-up. I am still very happy happy with my hitch and have had no issues. Great product and service.
by: Bill G.01/11/2014
The tow wiring kit was easy to install and the design made it an easy " plug & play installation. Just follow the easy to understand illustrated directions. The challenge was removing the plastic sides without damage but as work progressed, the sides, the seats (third row seating) and cargo box were easily tackled. With the proper tools and some patience you can DIY and enjoy the experience.
Bill G.
1/11/2015
After a year of use I have had no problems with the wiring harness. The installation was made easy with the plug and design. The excess time was mostly in the removal of the cars third row seats, tray and plastic sides but in the end the installation was not all that difficult.
by: Michael 07/04/2020
2008 Hyundai Santa Fe
This installed easily, just followed the excellent video. It also worked of course and got power to my trailer lights. Excellent product/service/instructions all around, thank you! Well, well worth the reasonable cost.
Michael
7/4/2021
After a year, Ive launched and retrieved about 20 times, so 40 submersions, still working fine.
by: Greg S06/08/2017
2011 Hyundai Santa Fe
Worked like a champ on a Hyundai 2011 Santa Fe. Towed a trailer from Seattle to Ashland, OR and then to Spokane, WA. Zero problems.
The ball mount clunks a little as it moves around inside the receiver when driving. A little annoying but I shimmed it with a couple of thin pieces of HDPE plastic to quiet it down.
Installed the hitch by myself which was a pain. A second set of hands would have been very helpful. I didn't remove the muffler just moved it out of the way with a piece of wood.
Starting the bolts was a little tricky without help. Installing the wiring harness was straight forward and uneventful.
Derek S. at eTrailer was very helpful with steering me towards the correct wiring harness. Would buy from these folks again.
by: Rich J.02/24/2014
This product makes it so easy to wire your vehicle. Remembering back to early wiring installations, they were difficult locating and running wires. This is really a 30 minute job, start to finish!
Rich J.
2/24/2015
Light system is operating as reliably as on day 1!
by: Terry 04/28/2021
2008 Hyundai Santa Fe
I recently installed a tow bar on my 2008 Hyundai Santa Fe primarily to be used for a bike rack. I decided to order this trailer wiring harness in case I ever need to tow a small trailer. This wiring kit is simple to install and does not require any wire splicing or wire taps. The installation video tells you exactly how and where to install the components of this harness kit. I'm very pleased with this kit.
by: Leonard 09/16/2022
This wiring harness fit my vehicle as expected. It was plug and play. The directions that came with it were a little sparse but was able to figure it out. there is probably a video out there but did not take the time to search for it. Overall very satisfied with the harness.
by: Bill R.08/21/2015
2007 Hyundai Santa Fe
Well designed product. Watched the instructional video first and installation only took a few minutes. Be sure to ground to bare metal, even if you have to scrape a little paint off the grounding point first.
Bill R.
8/20/2016
Top notch design. Very easy install and very easy to remove when I sold the vehicle.
by: Russ H.07/25/2013
2007 Hyundai Santa Fe
I installed this wiring harness on my 2007 Hyundai Santa Fe SE with the third row seating. Installation was very easy, especially after watching the associated video. I would say that overall the installation only took about 30 minutes to complete.
I used a short length of wire to fish each end of the harness up behind the side trim piece to the rear lighting connector. I pull a popup camper and this product worked flawlessly on a recent camping trip.
by: Joseph11/01/2017
2009 Hyundai Santa Fe
product worked as i planned. used it to convert bumper reflectors on my 2009 hyundai santa fe to tail and stop lights. now able to switch the trailer plug from the auxilary bumper lights to my trailer lights hen trailering. easy to install and decent price.
by: Dave S.08/26/2014
2008 Hyundai Santa Fe
Perfect fit and used video to install on 2008 Santa Fe without towing package. Very easy to install.
Dave S.
8/31/2015
Product still works like new and I am very satisfied!
by: Bob S07/26/2013
Installation could not be easier. In fact you only have to remove 3 screws to remove the lower tray that holds the jack if you have a flexible pickup tool to snake to wires up on both sides. Took less than 1/2 hour to install and put everything back together, I used one of the taillight screws as a ground point, just scrape some paint off around the screw. No worry about splicing into the vehicle harness, plug and play.
by: John M.06/24/2014
The first time I had to replace the wiring harness I took it back to the dealer and it cost over $150. This time I purchased the product from etrailer and thanks to the very explicit video instructions was able to replace the unit in less than 15 minutes at less than one third the cost. Very satisfied with the cost, speed of delivery and helpful company.
by: Bill 04/26/2021
Very good product, my second wiring harness from etrailer. Two small problems: the double-sided which was supposed to be included to secure the module was NOT included. Also, the paper instructions included with the package do not agree with the youtube video produced by etrailer. The video is better.
25
217
Show More Reviews
See what our Experts say about this Tekonsha Custom Fit Vehicle Wiring
- Recommended Wiring to Install Tekonsha Prodigy P3 Brake Controller on a 2010 Hyundai Santa FeTo install the Tekonsha Prodigy P3 Brake Controller # 90195 on your 2010 Hyundai Santa Fe, you will need to do some cutting and splicing. This is not a difficult process when you have a 4-way trailer connector and use the Universal Brake Controller Wiring Kit # ETBC7. This kit gives you everything you need to make a trailer connection for a trailer with brakes. It includes all the wiring, circuit breakers, and connectors for installation. This will allow your brake controller to communicate...
view full answer... - Draw-Tite Trailer Hitch Fit for 2011 Hyundai Santa FeThe Draw-Tite Class III Receiver Hitch # 75684 is confirmed to fit the 2011 Hyundai Santa Fe with two small pipes on the same side. However, # 75684 will not fit models with a dual exhaust (exhaust pipes on both the driver and passenger side of the vehicle). I have attached an installation video of this trailer hitch on a 2011 Santa Fe for you. If you are thinking of doing any towing, I recommend our etrailer.com Ball Mount Kit for 2 Inch Hitches # 989900. This kit includes 2 ball mounts,...
view full answer... - Trailer Wiring and Trailer Hitch for a 2010 to 2012 Kia Forte SedanThe trailer wiring for a 2010 to 2012 Kia Forte, # 118415, will connect in line with the tail light wiring inside the trunk of the vehicle. The trailer connector will remain inside the trunk until it is needed. It can be pulled out and the trunk closed on it (the weather stripping will protect the wires, avoid the locking mechanism). I have included a link to the installation instructions for you. It does take some careful movement of the hitch to get it into place as you can see in the...
view full answer... - How to Select a Ball Mount for a 2007 Hyundai Santa Fe and Other Items for Towing a Travel TrailerTo determine the correct ball mount to use for your Hyundai Santa Fe with a Class III 2 inch receiver hitch and the Jay Feather Ex Port 17c travel trailer you will need to measure from the ground to the top of the receiver hitch opening on the Santa Fe and from the ground to the bottom of the trailer coupler on the travel trailer, with the trailer parked on a fairly level surface and the trailer frame level. Once you have those measurements, you can subtract the height of the Santa Fe...
view full answer... - Complete Towing Package for a 2010 Hyundia Sante Fe Towing a Travel Trailer with Weight DistributionI would recommend the Draw-Tite Trailer Hitch, item # 75684, for your 2010 Hyundai Santa Fe. This hitch has a 5000lbs gross trailer weight rating and 500lb tongue weight rating, when used with a weight distribution system. You will need to check the towing capacities of your vehicle in the owners manual or at the dealer to determine if the vehicle is capable of towing the load you will require. The best weight distribution system for your trailer will be one that matches the tongue weight...
view full answer... - Is Trimming Required to Install Curt Trailer Hitch on 2012 Hyundai Santa Fe Limited w/Dual ExhaustOn a 2012 Hyundai Santa Fe, when installing Curt trailer hitch # C13073, you will need to trim the heat shield under the vehicle. Technically, you could just fold the area of the shield that would interfere out of the way but this might make installation more difficult. The bumper does not have to be trimmed and you cannot see the heat shield unless under the vehicle. I have linked a video showing an installation of the hitch and it also shows trimming the heat shield. If your father plans...
view full answer... - Comparison of Trailer Wiring Harnesses # 118415 and # 118258 for a 2009 Hyundai Santa FeMy preference between the two wiring harnesses for the 2009 Hyundai Santa Fe would definitely be to go with the Tow Ready # 118258, if the vehicle has a factory towing package. The other wiring harness, part # 118415, is for models that do not have the tow package. The Tow Ready wiring harness keeps as much of the harness and connections inside the vehicle as possible, keeping the 4-Way trailer connector and wiring safe and dry when not in use. You can view the installation instructions...
view full answer... - Are Lights Required on Pro Series # 63153 Cargo Carrier Installed on 2012 Hyundai Santa FeLighting requirements can vary widely from state to state, but generally speaking, if the cargo carrier or the cargo stored on it obscures your taillights, it's a good idea to install a light kit. You can contact your Sate Highway Patrol or Police for specifics. I really like the # 59516 LED light kit. The LED lamps are very bright, yet they draw only a fraction of the power that incandescent lamps do. I also really like the rugged wiring pigtails used by the light kit. The light kit...
view full answer... - Trailer Hitch, Wiring, Ball Mount, Hitch Ball and Bracket Recommendation for a 2012 Hyundai Santa FeMy recommendation for trailer wiring for your 2012 Hyundai Santa Fe with factory trailer wiring package would be the Replacement OEM Tow Package Wiring Harness, # 118258. Keep in mind that this harness is a replacement harness and, if your vehicle did not have the factory connector installed when it was new, you will need to access the tow package connectors and check them with a circuit tester, like part # PTW2993, to be sure that the wiring is complete on your vehicle. If you find that...
view full answer...
- Parts Need to Add a Trailer Brake Controller to a 2012 Hyundai Santa FeIn order to install a brake controller on a 2012 Hyundai Santa Fe you will need to hardwire it in. There are 3 things you will need: a 4-Way wiring harness, a # ETBC7, and a brake controller. If the Santa Fe does not already have a 4-Way you will need to add one using # 118415. If it does have a 4-Way you can skip to the next step. I have linked instructions and a video showing a typical installation for you. (If the vehicle came with the factory tow package then you would use 4-Way #...
view full answer... - Recommended Parts to Tow a Trailer with a 2012 Hyundai Santa FeThanks for reaching out! I recommend installing the etrailer Trailer Hitch Receiver # e75AR on your 2012 Hyundai Santa Fe because it's a Class III trailer hitch with a matte black finish that blends in better and is more durable than the glossy black finish we see on the other hitches. To complete your towing setup I recommend using Tekonsha T-One wiring, part # 118258 if you have the factory tow package or part # 118415 if you don't have the factory tow package, as well as a ball mount...
view full answer... - Trailer Hitch & Wiring Harness For 2011 Hyundai Santa Fe Limited to Tow Boat TrailerThe best I can give you is a maybe because you didn't say how much the bass boat and trailer weigh, or if you have the tow package or not. So if your 2011 Hyundai Santa Fe does not have the tow package it has a 2,000 lb towing capacity; with the tow package it has a 2,800 lb tow capacity. So if your bass boat and trailer weight that or less, you can tow it. For that you will need the following: - Draw-Tite Max-Frame Trailer Hitch Receiver # 75684 And - WITHOUT Tow Package: T-One Vehicle...
view full answer... - Will a Draw-Tite Trailer Hitch Fit a 2008 Hyundai Santa Fe with Optional Third Row SeatingThe Draw-Tite Trailer Hitch, # 75471, is listed as a fit for all models of the 2007 to 2009 Hyundai Santa Fe. I have included a link to the installation instructions for you and a link to a video showing a typical installation. If you plan on doing some towing, I recommend the etrailer Ball Mount Kit, # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip, and a carrying bag. For trailer wiring there are 2 options. If the vehicle does NOT have a factory tow package, use...
view full answer... - Adding 7-Way Connector/Bracket and Wiring to 2011 Hyundai Santa Fe Without Drilling the BumperI believe I have a solution for you! Taking into consideration the space limitation you have and your resistance to cutting into your bumper, you can use the Draw-Tite, No-Drill Mounting Bracket # 18136 with the Universal Installation Kit # ETBC7. I have attached a brief installation video of the # ETBC7 on a similar vehicle. From there, because you are installing a 7-way, you will also need a 4-pole flat that will connect to whatever accessory you are installing, whether it be a brake...
view full answer...
- Fit of CURT Class III Receiver Hitch Part # C13073 on 2012 Hyundai Santa Fe with Dual ExhaustAccording to our friends in Tech Services at CURT Manufacturing, the Class III receiver, part # C13073 will indeed fit a 2012 Santa Fe with dual exhaust. You might also need the following: Wiring Harness with 4-pole Trailer Connector, part # 118415, or # 118258 if your Santa Fe is equipped with the tow package. Ball Mount, part # D-4 Hitch Pin and Clip, # PC3 1-7/8 Inch Trailer Ball, part # 19260 2 Inch Trailer Ball, part # 19247 2-5/15 Inch Trailer Ball, part # 63847 To see the install...
view full answer... - Trailer Wiring Harness Options for a 2011 Hyundai Santa FeThe Replacement OEM Tow Package Wiring Harness, # 118258, is designed as a replacement for a factory wiring harness and/or for those 2011 Hyundai Santa Fe models that have a towing package. If your Hyundai Santa Fe does not fall into this category then you need # 118415. If this does describe your Santa Fe, then you are correct, the connectors and converter are designed to remain in side the vehicle. The point at which the connectors are pushed through from the outside to the inside of...
view full answer... - Recommended Trailer Hitch and Wiring for a 2010 Hyundai Santa FeI recommend going with the Draw-Tite Trailer Hitch # 75684 which is a Class III hitch with a 2" receiver. This trailer hitch will fit your 2010 Hyundai Santa Fe as long as you don't have the dual exhaust and it doesn't requiring cutting of your rear fascia like the Curt trailer hitch does. Then for wiring I recommend the Tekonsha T-One as we have found the Tekonsha wiring products to be the most reliable. If you have the factory tow package use part # 118258 otherwise you need part #...
view full answer...
- Trailer Wiring Harness for 2013 Kia Forte KoupFor the 2013 Kia Forte Koup, Curt recommends their Circuit Protected Taillight Converter, part # C56175. The # 118415 you referenced will only work with the sedan model, as the taillight assemblies differ between the sedan and koup model. The C56175 is not a vehicle specific item and would require tapping directly into the taillight circuits of the vehicle. I have linked you to the installation details for the wiring harness. You would need to access the wiring harnesses feeding the taillight...
view full answer... - Curt Hitch C13073 versus Draw-Tite 75684 for 2011 Hyundai Santa FeCurt offers a round tube Class III receiver, part # C13073, but to satisfy their warranty requirements, a stabilizer strap # 18050 needs to be used for non-trailer loads like a bike rack or cargo carrier. If you intend on only using the receiver for towing, the Curt would be a good choice. The Draw-Tite # 75684 is constructed of square-tube steel. Because of the spoiler on top of the hatch, the stabilizer strap will not work well on the Santa Fe, so for a bike rack or cargo carrier, the...
view full answer... - Will Installing Draw-Tite # 75684 on 2010 Hyundai Santa Fe Prevent Lowering of Spare TireAs you can see in the provided photo, installing the Draw-Tite Class III receiver on your 2010 Hyundai Santa Fe will somewhat obstruct the spare tire. You will still be able to deploy the spare tire if while lowering it, you push the edge of the tire toward the front of the vehicle until it clears the hitch. The hitch on my wifes van is obstructed in exactly the same manner, and I can tell you from experience that getting the spare lowered is no big deal. If you were planning on using...
view full answer...
- Correct Trailer Wiring Harness for a 2011 or 2012 Hyundai Santa Fe with Towing PackageAt this time the correct choice for the 2012 Hyundia Santa Fe SE with towing package is the Draw-Tite custom fit wiring, # 118258. Draw-Tite has tested this harness on the 2011-2012 models and verified that it will work without issue. I have attached a link to the installation instructions for you to review also. You should verify, with a circuit tester, # PTW2993, that the connectors on your Santa Fe are fully functional before purchasing the tow package wiring harness. If one or more...
view full answer... - Does the Custom Fit Vehicle Wiring for the 2010 Hyundia Santa Fe Provied Overload ProtectionYes, the Tow Ready Custom Fit Vehicle Wiring for the 2010 Hyundai Santa Fe, item # 118415, is circuit protected. This means that if there is a short on the trailer the module will protect the vehicle circuitry. With the 118415 module the harness would need to be replaced in this situation. If you would like a converter that is circuit protected and can be reset in the event of a short circuit situation, you could use the ZCI Circuit Protected Vehicle Wiring Harness with Install Kit, item...
view full answer... - Using ETBC7 Brake Controller Install Kit on 2009 Hyundai Santa FeI do have instructions for you, but they're general in nature, not vehicle specific. The good news is that the installation method doesn't vary much from vehicle to vehicle. I'll link you to an install video showing the kit being used to install a brake controller on a 2012 Santa Fe. The procedure on your 2009 model would be very similar. If your Santa Fe does not have a 4-pole trailer connector, you will need part # 118415. The 7-way trailer connector included in the install kit will...
view full answer... - How to Tell if a 2007 Hyundai Santa Fe Already has Trailer WiringCheck the rear of your 2007 Hyundai Santa Fe and see if there is already a 4-Way installed at the rear or if it is possibly sitting on the inside of your hatch area possibly under one of the panels. If you cannot find the 4-Way then you don't already have one installed. If you don't already have a 4-Way then odds are that you don't have the tow package and you would need the T-One # 118415. The T-One # 118258 is for if your Santa Fe came with the tow package and you are replacing your...
view full answer...
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Robert G
Expert Research:
Jameson C
Expert Research:
Adam R
Video Edited:
Zack K
Video Edited:
Andrew K
Video Edited:
Patrick B
Video by:
Joshua S
Test Fit:
Nicholas E
Test Fit:
Rick A
Updated by:
Laura H
Updated by:
Wilson B
Updated by:
Alexander C
Updated by:
Isabelle B
Installed by:
Cole B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Dewayne
10/24/2023
Excellent hitch. Ive had no issues whatsoever. Would definitely recommend.