Using ETBC7 Brake Controller Install Kit on 2009 Hyundai Santa Fe
Question:
Do installation instructions come with this product that is specific to my vehicle 2009 Santa Fe?
asked by: Chris
Expert Reply:
I do have instructions for you, but they're general in nature, not vehicle specific. The good news is that the installation method doesn't vary much from vehicle to vehicle. I'll link you to an install video showing the kit being used to install a brake controller on a 2012 Santa Fe. The procedure on your 2009 model would be very similar.
If your Santa Fe does not have a 4-pole trailer connector, you will need part # 118415. The 7-way trailer connector included in the install kit will plug into the 4-pole once it is installed, with 4 loose wires remaining. The blue wire will run under the vehicle, through the engine compartment and through the firewall, ultimately connecting to the blue wire on your brake controller. The black wire will provide power to the trailer connector for any trailer-mounted accessories requiring 12-volt power. It will attach to the positive battery terminal via the 40 amp circuit breaker included in the kit. The white wire would be grounded to clean metal on the vehicle. The purple wire is typically used for reverse lights on the trailer, if it is so equipped. If this circuit is not needed, this wire can simply be bundled up out of the way.
The controller itself would mount under the dash within easy reach of the driver, typically to the right of the steering column. The controller will have 4 wires exiting the rear. The blue wire would attach to the wire ran from the rear of the vehicle, the white wire would ground to the negative battery terminal, the black wire would attach to the positive battery terminal via either the 20- or 30-amp breaker (depending on which is specified in your brake controller instructions). The red wire attaches to the cold side of the brake stoplight switch. This switch is located at the top of the brake pedal and can have several different wires exiting it. Use a circuit tester like part # PTW2993 to locate the wire that shows current only when the brake pedal is pressed (probably green w/ black stripe or gray w/ black stripe, but you should still test it.) Once this wire is found, tap the red wire into it.
I've linked you to some FAQ articles that you might find helpful. I will also provide a link to the instructions for the 4-pole connector.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Product Page this Question was Asked From
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: How to Choose the Right Trailer Hitch Class
- Article: How to Measure for Trailer Hitch Drop
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Where Do the Wires on the Universal Install Kit for Trailer Brake Controllers Get Installed?
- Q&A: 2022 Toyota Highlander Wiring for a 7-Way Blade Connector
- Q&A: Should I Get a Proportional or Time-Delayed Brake Controller
- Q&A: Parts Needed to Tow Trailer With Brakes Using 1992 Dodge D250
- Q&A: 4-Flat Trailer Wiring For 2024 Jeep Wrangler With Tow Bar Wiring