Summer Starts Here - Save up to 70%
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your Ford Edge with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side tail lights. Once you've plugged in the T-connector, run the hot lead up to your car battery. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery.
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. This converter is a circuit-protected, battery-powered unit that bypasses the electrical routes that are used by a basic wiring harness. As a result, there is virtually no draw on your tail light circuits.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
California residents: click here
Average Customer Rating: 4.8 out of 5 stars (152 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.
Pretty easy install worked great and still working great a year later. Hardest part was finding a good location to mount the controller below driver side tail light but figured it out and watched a YouTube video but the mounting of the controller wasn't in the video they skipped that step. Ran the 12 volt power lead wire up to engine bay along driver side frame rail and attached to brake lines and fuel lines with zip ties.
This harness appears to be of excellent quality, and is the perfect thing needed to set up my vehicle for utility lights the right way. The only reason for four stars is that I have not actually installed it as yet, so have not had opportunity to test it.
Showed up timely and fit like a glove on our 2012 Ford Escape. The wiring harness was very easy and directions easy to follow. The hardware for hitch was all there and also easy to install. Thanks!
I wired my Harness in myself and a year later it's still Top Notch? Excellent product.
Worked great and still working great after a year
this was one of the best companies to deal with. they kept in contact the whole time. they made sure everything arrived on time. that, to me is priceless... the hitch and harness is great. easy instalation. looks super.. I am extremely happy with the whole process.... top notch everyone....
Was easy to install the directions could have been little better to work out but i watched video of it and was simple. Hardest part was running wire to battery.
Awesome, helpful staff, set me up with the right wiring kit.
Working perfectly.
Good product bad was the wiring for the box was short
can't believe it arrived in less than a week! Best price I found online. Fit perfectly and only took 30 min to install. Happy to write a review for future customers since past reviews were what tipped my vote. Thank you etrailer!
Clear well written instructions and videos. Took less than 30 mins for 16 yr old to install
It was easy to install
The wiring harness came with everything I needed for the installation. The hardest part of the installation was running the 12 volt power wire from the rear of the car to the engine compartment. I purchased the optional weather-proof connector wit the heat shrink tubing. This ensures a good waterproof connection for the wiring. The only minor complaint that I have is that I don't like the dangling trailer electrical plug-in. It would be nicer if the plug-in could have been mounted to the bottom of the bumper.
Michael
5/21/2020
This trailer wiring harness has functioned flawlessly and is holding up to frequent use quite well. However, I still think that the connection point for the trailer plug in should have a bracket or clip to firmly attach to the rear bumper of the vehicle.
Ordered a hitch and wiring for my 2012 escape.wiring was not available.called and talked to Stacey who found another available harness had them both shipped out and received them in 5 days.i had already read on their website how to install them.i have above average installation skills and installed the hitch and wiring in about one and a half hours.very pleased with quality and ease of install.service was also excellent.
Charles T.
9/27/2018
Have had no problems hitch and wiring works great very good quality and ease of installation.
Excellent fit
Complete kit. Everything needed include d.
works excellent.
Harness fit good and was easy to install. Only four stars because the video had stated the connectors were upgraded to heat shrink connectors but my connectors were not. I did have some of my own so I swapped them out.
Rachael H.
7/31/2018
This kit included standard butt connectors, but as referenced at about 4:10 in the video the connectors were upgraded to part # DW05745-10. A link to those upgraded heat shrink connectors can be found here.
Helpful Links
This was my second trailer wiring kit for my 2010 Ford Escape. The first one stopped working correctly after about 4 years due to somehow the little module that was mounted with double sided tape behind the tail light came loose and was dangling down where it was exposed to the elements. The second unit was mounted with a screw and worked like a charm. The only minor difficulty is running the power wiring up to the battery in a manner that it is protected and out of the way. Other than that, easy fast installation in one evening. I’ve since traded that vehicle so I can only assume it’s still working.
Installed this on my son's 2011 Ford Escape. Using the simple to follow instructions and the Videos provided by Etrailer made this a simple project. We installed this in conjunction with a receiver hitch, which we also ordered from Etrailer.
You had what I couldn't find anywhere else thank you
As usual, etrailer stuff is great. This, just like my two Priuse's harnesses fit perfectly and include all the parts to finish the job and have a reliable installation.
Very satisfied with the product. The package arrived a little beat up with a significant gash in the side of the box, but the hitch was undamaged and all parts were intact. The hitch installed easily, everything fit as needed, though why the need for a spaced between the hitch and the frame on the passenger side really doesn't make sense, it looks like a fix for a hitch with incorrect mounting hole locations. And that did make the installation a little more difficult, but manageable. The wiring harness also installed easily, everything needed was there and everything worked as it should. I'm quite satisfied.
Harness is of good quality and plugged right in to the factory wiring. Easy to install other than having to run a wire back to the battery to power it. The separate power is nice in that the trailer light circuit is isolated from your vehicle tail lights and turn signals.
Great kit that worked very well! Some of the connectors were exposed and eventually corroded. This was remedied by cutting the connectors off and soldering the connections. In hindsight, I would recommend doing this initially for any exposed connections. Other than that I have no complaints.
Do you have a question about this Custom Fit Vehicle Wiring?
Condition: Like New
Notes: May have damaged packaging or minor cosmetic blemishes.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Dw
6/27/2023
Well over a year and product is just fine. Thank you for the follow up!