Trailer Hub Wheel Stud - Drive In - 1/2" Diameter x 2" Long - Qty 1
(91 reviews)
Price: $8.42
In Stock
Trailer Hub Wheel Stud - Drive In - 1/2" Diameter x 2" Long - Qty 1
Item # 7-122
Retail:$9.06
Our Price: $8.42
You Save: 7%
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (91)
- Q & A (0)
- Videos (1)
- Photos
Redline Accessories and Parts - 7-122
- Boat Trailer Wheels
- Trailer Hubs and Drums
- Trailer Tires and Wheels
- Wheel Studs
- Drive-In Stud
- Redline
- 1/2 Inch Diameter
- 2 Inch Long
Replaces a drive-in wheel stud for your trailer hub. 1/2" Diameter bolt.
Features:
- Replaces a drive-in wheel stud for your trailer hub
- Diameter: 1/2"
- Length: 2"
- Includes 1 bolt
 | ||||
| Thread Diameter (A) | Stud Length (B) | Spline Length (C) | Base Length (D) | Spline Diameter (E) |
| 1/2" | 1.99" | 0.62" | 0.73" | 0.61" |
7-122 Trailer Hub Wheel Stud - Drive-In - 1/2" Diameter x 2" Long - Qty 1
Video of Trailer Hub Wheel Stud - Drive In - 1/2" Diameter x 2" Long - Qty 1
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Redline Tires and Wheels 7-122 Review
Today we're going to take a look at the replacement drive-in trailer hub wheel stud. This is a half-inch diameter, two inches long, and a quantity of one. This half-inch stud is designed to replace a damaged wheel stud on your trailer hub. The raised spline portion of this stud is what will be driven or pressed into your trailer hub. The stud is what will go through the bolt hole on your trailer wheel. When used with a wheel lug nut will hold your tire and wheel to your axle. The head of it is stamped as grade eight bolts.
Again, the thread size, the diameter of the thread is a half-inch. There's 20 threads per inch. It does use the standard half-inch by 20 lug nuts. I did happen to pull one of those from our warehouse, just to show you what it looks like. When this on your trailer hub, you put your wheel up on the stud, and then just go ahead and put your lug nut on there.
Tighten it down. Torque it to specs, and your tire and wheel is all connected to your axle. A few measurements on this. The overall length is measured from the bottom of the head to the end of the bolt, two inches. The threaded portion, if we measure just that is 1-1/4 inches. Then the diameter of the spline, that's the portion that gets pressed into the trailer hub.
The diameter on that is 0.61 inches. That should do it for the review on the replacement drive-in trailer hub wheel stud, half-inch diameter, two inches in length, and a quantity of one.
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
- Did not arrive in time
- Wrong item was ordered
- Alternate product found
Customer Reviews
Trailer Hub Wheel Stud - Drive In - 1/2" Diameter x 2" Long - Qty 1 - 7-122
Average Customer Rating: 4.8 out of 5 stars (90 Customer Reviews)
Replaces a drive-in wheel stud for your trailer hub. 1/2" Diameter bolt.by: Zachary 01/30/2024
This was exactly what I was needing. It took me a little while to find it since this was not offered anywhere else, at least that I could find. I installed this on my 2022 Vengeance Rogue 32V camper. It was a perfect fit. It shipped in & arrive at may house in more than a reasonable time but who am I kidding. etrailer has always taken care of my trailer needs over the years. Dont overthink it. etrailer has your back.
by: Edward 08/15/2022
genuinely surprised how difficult it was to find this wheel stud around town. I found it here and bought two just in case. Good quality and identical to the original.
by: Lee 03/07/2024
It's a stud. It hasn't broke or fallen off.
by: CN04/22/2024
Perfect match for what I am replacing!
by: Chase 07/15/2022
Exactly what I was looking for and the only website/company that had the right size and came in quicker than I had expected
Chase
7/16/2023
Great never had any issues with the wheel studs
by: William 04/07/2023
These were a perfect fit for my 5th wheel and Kimberly did an excellent job helping me find the correct part! Great customer service!
by: Bruce 10/06/2021
Identical size and shape to the old studs in a 12"x2.5" hub for 5200# axle. Hopefully will last longer though.
If you can get the old broken lugs out, these are easy enough to hammer in.
Bruce
10/7/2022
No problems over the last 8k kms
by: Michael 11/13/2023
Exactly what I needed!
by: Jonathan04/14/2022
The Hub Drum matched perfectly with the setup that was there before. I am giving them five stars because everything was how they said, and it matched perfectly. I wish they also add a cotter pin to the kit. That way, you do not have to go and get one to complete the job.
by: Calvin01/30/2019
This was exactly what I required to repair my Wells Cargo utility trailer. The support staff at e-trailer are absolutely great and quick to respond to any of my inquiries. Won't hesitate to use them again.
Calvin
1/31/2020
Great. Replacement studs were exact match to original equipment on my Wells Cargo trailer.
by: Paul 07/02/2021
Great replacement wheel studs
Paul B.
7/3/2022
Quality product that stands the test of time
by: Tim03/30/2018
Perfect match for replacing the damaged studs on my Dexter trailer hub /brake drum. And etrailer provided the expertise. Saved me time and money.
by: Lisa 08/05/2020
I want to say that I have never been so satisfied with anyone as this particular company. Their customer service reprsentative was knowledgeable. Very patient at helping us
find our special find of a car trailer wheel. We had a misfortune and had to order just
one of the wheels again a few weeks later and they were able to make it very painless to find what we needed again. I would recommend e-trailer to anyone! Great place to shop!!
by: Paul08/24/2022
Satisfied with the product & delivery, and good customer service from etrailer throughout the years.
by: Nav gill05/15/2017
Simply the best. Best price, best quality and easy to install. Also there are great videos etrailer has for installation of most of their parts. Dont waste your time shopping around. These gutd have the best price. Thanks guys
by: Verney10/27/2020
10/27/20 Just got the studs. The .61 diameter spline fit perfectly. Glad you recommended getting two instead of one. Now I can fix the trailer hub and not worry about it breaking under a load.
by: Dylan04/20/2023
Only place I could find this stud.
by: Robert06/05/2020
etrailer had the parts required and was the quickest at delivering the needed parts. Bill with customer service researched the splinted wheel bolt OEM data for me and found what was needed.
Great Customer Service!!!
by: Terry02/20/2017
All the parts I ordered have arrived as promised and worked as they should, I will order from etrailer again as needed.
Linda B.
2/20/2018
still working
by: Richard O 07/31/2017
Lug studs fit perfectly. Used to replace broken wheel studs on my 44 ft Haulmark race car trailer. Great price and quality.
by: Erin08/07/2020
Trailer lug nuts were the perfect fit and shipped quick!
by: Jeff11/28/2021
After receiving a product that was the wrong size I contacted customer service and ordered these which fit perfect. The customer service at etrailer was a pleasure to deal with, in fact the best company I have ever had the pleasure of dealing with. Thanks so much to the employees for doing such a great job.
by: John 04/17/2023
They are the size I needed, I hope I never have to use them.
by: NickO08/26/2020
Parts as expected. Looked all over the internet and etrailer was the place with a detailed drawing of the part I needed! Thanks for the drawing.
by: Kim03/23/2020
I’m writing to praise Braden E in Customer Service. Braden spent a great deal of time with me in researching exactly what hubs I needed for a very old axle. At one point I asked Braden if he was the owner. Why? Because I was struck by his attention to my needs, his tenacity and persistence in getting things right. He is truly an asset to the company. I think Braden is a rare breed these days. I’ll be a repeat customer because of my interaction with him.
25
90
Show More Reviews
See what our Experts say about this Redline Accessories and Parts
- Replacement Wheel Stud with 1/2 x 20 and .62 Spline DiameterIt sounds like the Trailer Hub Wheel Stud - Drive In - 1/2" Diameter x 2" Long - Qty 1 # 7-122 is what you're looking for. This is a 1/2" x 20, 2" long stud with a .61 spline diameter-which is the closest we've got to your .62; this could just be down to a slight difference in the measurements taken and I believe this should work for you.
view full answer... - Replacement Wheel Stud for Dexter 3,500 lb Trailer HubFor a Dexter 3,500 lb trailer axle hub the correct replacement wheel stud is the part # 7-122.
view full answer... - Replacement Wheel Stud 1/2" Diameter x 2" LongThe Trailer Hub Wheel Stud part # 7-122 which measures 1/2" diameter x 2" long with a .62" spline length would be the best match option we have for you.
view full answer... - Can Wheel Studs on Brake Hub/Drum Be ReplacedYou should be able to replace the wheel stud, but you'll need to drive the stripped stud out and get the measurements shown in the provided diagram in order to locate the correct replacement. You'll need a drift punch that is smaller in diameter than the wheel stud and a heavy hammer. If you have a hub/drum for a 3500 lb axle (like the # AKHD-655-35-EZ-K you'd looked at), the replacement wheel stud would be # 7-122. If you have a different hub, provide me with the measurements shown in...
view full answer...
- How Much Smaller Should Hole Be Drilled for Press-In Wheel StudsWhen drilling a hole for a press-in wheel stud you want to drill the hole .006-.016 inch smaller than the knurl diameter of the stud. The part # 7-122 has a knurl diameter of .61 inch.
view full answer... - How To Measure Current Wheel Studs To Determine An Adequate ReplacementWhile we do not carry the exact same wheel studs as the one's you're looking for, however I'd be happy to help you measure your wheel studs to see if we have a comparable replacement. What you're going to want to do is, measure the A-F measurements shown below with a set of calipers # PTW80157, and provide that measurement for me. For instance, the Trailer Hub Wheel Stud # 7-122 has a 1/2" diameter, is 2" long, and has a spline length of .62". If you're able to provide some information...
view full answer...
- Replacement Wheel Stud For Dexter Hub and Drum Assembly K08-426-91I reached out to my contact at Dexter and for a replacement stud compatible with the Dexter Trailer Hub # K08-426-91 you have you will need the # 7-122. This will be slightly longer than your current studs but all of the other dimensions are the same. I included a video of the # 7-122 for you to take a look at.
view full answer... - Wheel Studs for a Load Rite Boat TrailerI recommend using the Trailer Hub Wheel Stud item # 7-122 to replace the wheel studs on your Load Rite boat trailer. These are a 1/2" diameter and 2" long.
view full answer... - Recommended Replacement Wheel Studs for Hub with 5 StudsFor your wheel studs, I believe you will want the Kodiak Wheel Bolt - 1/2" Diameter x 2" Long # K12WB2. Another close option but with a wider spline is the Trailer Hub Wheel Stud - Drive In - 1/2" Diameter x 2" Long - Qty 1 # 7-122. These are the closest options to your measurements for your hub. I've attached photos of these measurements for you to compare.
view full answer...
- Replacement Wheel Stud for Lippert 3,500 lb AxleThe standard replacement drive-in wheel stud for a 3,500 lb hub/drum like what you have on your Lippert 3,500 axle is the part # 7-122 which is the correct thread size and length.
view full answer... - How to Find Correct Replacement Wheel Studs for Forest River Wildcat 5th WheelIn order to find the correct wheel studs for your trailer you'll need to measure your existing since there is no way to look this up with the make and model of the trailer. The Trailer Hub Wheel Stud part # 7-122 for example measures 1/2" in diameter 2" long. If this won't work for you, please feel free to provide me with your dimensions or choose from the list linked below.
view full answer... - Availability of Single 1/2 Inch Diameter Wheel Stud The Redline Replacement Trailer Hub Wheel Stud Drive-In 1/2 Inch x 1-7/8 Inch # RG03-060 referenced in your question is available only in this set of 4. These are not currently available as a single item. We do have the slightly longer Trailer Hub Wheel Stud # 7-122 available as a quantity of one. This stud measures 1/2 inch in diameter and 2 inches in length.
view full answer... - Replacement Trailer Wheel Studs With 1/2 inch Diameter Thank you so much for the picture and the dimensions, that is exactly what I needed to find you a replacement stud. I recommend the Trailer Hub Wheel Stud - Drive In - 1/2" Diameter x 2" Long item # 7-122. I have attached a diagram showing the dimensions for this wheel stud. They are as close to your dimensions as I can find.
view full answer...
- Determining Which Replacement Wheel Studs Fit Dexter Hub and Drum AssemblyI would be happy to help you find the correct replacement wheel studs for your hubs, but unfortunately the part number shown in your picture are for the brake assemblies and not the hub. To determine the correct replacement wheel studs you will need to remove one of the studs and measure it. There are quite a few locations where you will need to measure the stud, and you will need to use digital calipers like # PTW80157 to get a very precise measurement. I included a diagram of where...
view full answer...
- Right Lug Stud Size For 3,500 lb Lippert AxleIn order to determine if the Trailer Hub Wheel Stud # 7-122 will work, you will need some measurements from your current studs. Referring to the the included diagram, you will need to at least have the measurements for A, C, and E. You will want to use a dial or digital caliper because precise measurements are needed.
view full answer...
- Replacement 1/2"-20 Wheel Stud for a Load Rite Boat TrailerIn order to replace the broken wheel stud on your Load Rite boat trailer, I recommend using the Trailer Hub Wheel Stud part # 7-122 for a 2" long stud or the Trailer Hub Wheel Stud part # 7-150 for a 2-3/32" long stud. You can measure your remaining studs to determine the correct length. The dimension for each of these replacement wheel studs can be found on the product page. If you also need a new lug nut then you will want to use the CE Smith Trailer Wheel Lug Nut part # CE11051 for...
view full answer... - Replacement Lug Studs for Al-Ko 8500 Hub and Drum on 2012 Keystone Hideout 19FLBWe don't have a database that tells us what the stud size is on that hub, but I was able to do a little bit of research and find some reports that say that your 1/2" thread by 2" long stud seems to be accurate. For that size wheel stud you can use the Redline # 7-122 lug studs you were looking at which are 2" long and have 1/2" threads.
view full answer... - Replacement Wheel Studs for Roadmaster Tow DollyRoadmaster doesn't sell the wheel studs as a separate item, just as a hub assembly. The hub assembly is available as a special order, but as I was told, it's pretty expensive. I did some research and found that the Roadmaster # RM-2050-1 uses a standard 3500 lb10 inch brake drum like # AKHD-545-35-EZ-K. If the holes for the wheel studs aren't wallowed out, you can use the # 7-122 replacement stud which is standard for a 3500 lb 10 inch brake drum, and would work fine for you.
view full answer... - Is There A Time Frame For When Wheel Studs Or Suspension Bolts Should Be Replaced There really isn't a time frame for when the studs need to be replaced since wear and tear can differ depending on usage and climate. If you feel your studs are starting to look bad or the threads are tore up then you'll want to pop one out of the hub and take some measurements to determine the correct replacement. For example, part # 7-122 is 1/2" in diameter and has a 2" stud length. If you're instead referring to the bolts for your suspension then the same rules apply. You'll measure...
view full answer... - Recommended Replacement Wheel Stud Bolts for Boat Trailer with Wheel Bolts Stamped 6109 SJThanks for your measurements, these were a big help! A great replacement wheel stud bolt for the bolt dimensions you provided is the # 7-122. A compatible nut with a zinc coating for better protection again corrosion, I recommend the # CE11051 The above parts are sold in a quantities of 1, so for a quantity of 4 you will want to update the quantity box on the page that I've linked below for you.
view full answer...
- Wheel Stud Replacement for Trailer Hub # AKHD-545-35-EZ-KFor a replacement stud for the Easy Grease Trailer Hub and Drum Assembly # AKHD-545-35-EZ-K the correct part number is # 7-122.
view full answer... - Replacement Wheel Stud and Electric Brakes for Tandem Axle Dump Trailer With 7k AxlesThere is no way to determine the correct replacement studs without more information. It could be 1/2", 9/16", or 5/8" so you will need to measure. I have attached a link below to all of our replacement wheel studs so you can choose the right one once you have your measurement. Assuming this is a modern trailer with a standard 7k axle you can use the etrailer Electric Trailer Brakes # AKEBRK-7-SA. These 12" x 2" brake assemblies fit a 5 bolt brake flange pattern. They are self-adjusting...
view full answer... - Replacement Wheel Stud for AL-KO 7230 HubFor your AL-KO 7230, the replacement wheel stud you most likely need is the 1/2" Diameter x 2" Long - Qty 1 # 7-122. This is the replacement for the Dexter Hub that replaced the AL-KO hub when Dexter bought them out. This should work well on your AL-KO Axle. I have linked the page to all your 1/2 inch stud options in case you have a different measurement.
view full answer... - Replacement Wheel Studs For Dexter Trailer Hub and Drum 42656I checked with Dexter and was able to verify the correct studs for the Dexter Trailer Hub and Drum 42656. Per Dexter the correct replacement is the 2" long stud, which is the following part number: - Trailer Hub Wheel Stud - Drive In - 1/2" Diameter x 2" Long # 7-122
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Expert Research:
Jackie C
Expert Research:
Jameson C
Expert Research:
Jeffrey L
Installed by:
Jeff D
Updated by:
Laura H
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Edward
8/16/2023
Stud still works as intended. It hasnt broke or come loose in the brake drum. Good product