Wheel Stud - Drive In 1/2" x 2-1/2" (Qty. 1)
(44 reviews)
Price: $10.80
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (44)
- Q & A (0)
- Videos (1)
- Photos
Redline Accessories and Parts - 165995
- Boat Trailer Wheels
- Trailer Hubs and Drums
- Trailer Tires and Wheels
- Wheel Studs
- Drive-In Stud
- Redline
- 1/2 Inch Diameter
- 2-5/8 Inch Long
Features:
- Replacement Trailer Drive-In Wheel Stud
- 20 threads per inch
 | ||||
| Thread Diameter (A) | Stud Length (B) | Spline Length (C) | Base Length (D) | Spline Diameter (E) |
| 1/2" | 2-1/2" | .68 | 1.38 | .54 |
165995 Wheel Stud - Drive In 1/2" x 2-1/2" (Qty. 1)
Video of Wheel Stud - Drive In 1/2" x 2-1/2" (Qty. 1)
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Redline Tires and Wheels 165995 Review
Speaker 1: Today we're going to take a look at the 1/2 inch by 2 1/2 inch Drive In Wheel Stud for a quantity of one. Now this is a replacement trailer drive in wheel stud. It is designed to be pressed into your wheel hub assembly. Right here the neural portion is what would be pressed in. Then this threaded portion is what your lug nut would screw on to. It is a 1/2 inch diameter.
Total length, which is measured from the top of that end cap here to the edge of the stub is right at 2 1/2 inches. It is a 1/2 inch by 20 thread size. Basically, if you have your standard 1/2 inch lug nut, you can see that that's what would screw on to this stud. Just like that. Then hold your wheel on to the hub.
But that should do it for the review on the 1/2 inch by 2 1/2 inch Drive In Wheel Stud for a quantity of one.
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
Customer Reviews
Wheel Stud - Drive In 1/2" x 2-1/2" (Qty. 1) - 165995
Average Customer Rating: 4.9 out of 5 stars (44 Customer Reviews)
by: Stan 02/08/2024
Exactly what was needed but took several weeks to arrive.
by: David05/25/2019
Only place that I knew the product was the exact one I needed... Like new after installing.
by: Randy C05/19/2014
Wheel studs were delivered as advertised, however they were not an exact fit in my application; the spline length was just a little too long and the head diameter was a little too wide. With a short spin on the grinding wheel both were fixed and they're now installed and working perfectly. I tired to source these studs from local auto parts stores and had absolutely no luck at all. Overall, etrailer.com website provided numerous options with varying stud lengths and thread patterns which ultimately saved they day!
by: Donald 03/21/2021
Just when I needed a hard to find part...... Bingo! eTrailer.com has it!
by: Rich01/01/2017
I ordered wheel studs, shackle straps, and nuts to replace rusty components on my trailer. These are additional parts after ordering new trailer springs from etrailer earlier. Everything fit up great, and now both my axles support the trailer. Yay!
Thanks to Etrailer for having all this stuff for quick delivery, and it saves a ton over the local shop.
by: Maureena09/16/2020
Was the correct product for the brake hub. What is really great is to talk to a person. So many web sites do not let you order by phone. As a retiree a lot of us are not internet smart and do not like to put our info on the internet. Thank you Noah for giving us a faster phone number to reach you at in case we had any questions or a problem.
by: Jessie B09/26/2019
Most excellent customer service! We had a critical job that was under a huge time constraint where we learned at the last minute that the wheel studs were too short. Order a large quantity (150pcs) of this extended stud on Wednesday afternoon and the full order arrived at out facility by 11:00am Thursday morning! Parts looked great and will save us big time! Thank you Adam E. and etrailer.com for your amazing service!
by: James 08/29/2020
after a long search i found the parts that i needed at etrailer, the staff member jenny b was great and helped me until we found what i needed,parts arrived and i installed, all working great, Thanks
by: Shawn10/10/2018
Fantastic support and quick shipper! I'll be back!
by: Chris 10/23/2021
Exactly the wheel stud I needed for my trailer.
by: Jody M.10/27/2016
Fast and easy, I'll be back next time I need parts for my trailers
by: John 12/03/2022
John
12/4/2023
Worked perfectly
by: Steve 07/18/2021
Have ordered here a number of times always got just what I needed and the right part everytime.
by: Rz06/16/2020
Good quality product at a good price. Press Fit perfectly in the holes.
by: Brian11/09/2018
Always dependable products.well made,no surprises.
by: James02/03/2019
I ordered this because I needed a fifth longer lug to go with the RG03-080 set I ordered. These lugs are identical.
by: James04/06/2015
Great product and fast delivery. It was a perfect match to the old one and went right in place with no problem.
by: t. wilkes09/21/2016
everything was good
by: Arnold06/16/2019
Had what I needed and delivered expediently. I could not find it locally even in the largest and heavy equipment parts outlet.
by: Ben 01/06/2022
Have not installed them yet. But they look just like the original ones.
by: Adib03/02/2021
we love the products we bought , and we love the price and the excellent
customer service.
by: Scott05/27/2017
Just as shown on Website and arrived a LOT faster than I thought it would with standard shipping. Very nice
by: Robert 11/05/2021
Perfect fit
by: Ronald03/01/2013
Just what I needed, bought a few spares
by: Bryan07/19/2019
Parts got here quick and were packaged nicely
25
44
Show More Reviews
See what our Experts say about this Redline Accessories and Parts
- Replacement 1/2" - 20 Wheel Stud OptionsWe have a few different lengths under the 1/2" - 20 wheel stud size so you'll wan to measure the length of what you currently have before ordering a replacement. 1-11/16" Long # K12WB169 1-7/8" # RG03-060 2" Long # K12WB2 2.24" 7-150 2-1/2" # 165995 2-11/16" Long # 7-262 2-3/4" # RG03-080 If you don't see your size you can also go a bit larger and use an open-ended lug nut.
view full answer... - Replacement Studs for a Trailer Hub and Drum Assembly # 42866UC3-EZThe replacement wheel stud you would need for your Trailer Hub & Drum Assembly # 42866UC3-EZ would be a Wheel Stud # 165995. Also, when you install the wheels onto your hubs you will want to torque them down to spec and then after 50-100 miles you will want to re-tighten them to the specified torque rating to prevent having the studs break in the future.
view full answer... - Availability of 2-1/2 inch Long Trailer Wheel StudThe closest option we have would be the part # 165995 which is overall 2-1/2 inches long, has a knurl diameter of .54., is 1/2-20, and has a spline length of .68 inches.
view full answer... - How to Determine Wheel Stud Replacement for Boat Trailer Hub H-1377Based on my research it looks like you have a hub for a 3,500 lb axle, though we do not have any exact reference for an H-1377 hub to go off of. You only need to know whether your hub uses screw-in or drive-in studs as well as the length of stud you need. This is going to require you to remove one of your wheel studs and if they are drive-in they will have a head on them like the 1/2" x 2-1/2" Wheel Stud # 165995. A screw-in like the 1/2" x 2" Wheel Stud # 25-53 will be completely threaded. I...
view full answer... - What Size Hole to Drill for Installing Redline Replacement Drive-In Trailer Wheel Stud # 165995My contact at Redline advised that their Replacement Drive-In Trailer Wheel Stud, part # 165995, which has a spline diameter of 0.54 inches, can be driven into a hole diameter from 0.50 inches to 0.52 inches. My contact at Dexter advised that if you are able to hammer the old stud out of the hub (from the front, opposite to how it was installed) without deforming the hole or changing its size, then the replacement should fit properly without any need to drill the hub. If needed a punch...
view full answer... - What Would Cause Threads of Wheel Stud to Be Unusable After Using Washer Method to Install ThemIt sounds like you are using a lug nut on the wheel stud # 165995 that has either damaged threads or a similar but different thread size which is destroying the stud. My brother had this happen to him once with a car and it took him a while to realize since the threads were pretty close. The size of the lug nuts you'd need to use is 1/2 inch diameter with 20 threads per inch like the # 12CLN.
view full answer... - Replacement Drive In 1/2"x20 Wheel StudsI may have an option but we do not offer a 2 1/4" long 1/2"x20 wheel stud. The closest option we have is Wheel Stud - Drive In 1/2" x 2-1/2" # 165995 which is 2.5" long, spline length is .68", base length is 1.38" and is 1/2" x 20 TPI. This is wheel stud is sold in a quantity of one. I included a video of the Wheel Stud # 165995 for you to take a look at.
view full answer... - Replacement Stud Recommendation for Dexter 6k Rated Trailer HubsFor Dexter 6k rated hubs like the part # 8-201-9UC3-EZ you will need to use stud # 165995. This drive-in stud is 2-1/2 inches long.
view full answer... - Wheel Stud Replacement for 5200 lb Trailer Axle Based on the dimensions you said you needed the Wheel Stud # 165995 would be exactly what you'd need.
view full answer... - Torque Rating for Trailer Hub Wheel Studs for 1/2 Inch Lug NutsWheel stud # 165995 is a drive-in wheel stud meaning it gets driven into a hub with a mallet or similar tool. Since it is a 1/2 inch the lug nuts, when tightened, 1/2 inch lug nuts should be at 75 to 85 foot pounds on 8 inch to 14 inch steel or aluminum wheels, 90 to 120 foot pounds for 15 to 16 inch steel wheels, and 90 to 100 foot pounds on 15 or 16 inch aluminum wheels.
view full answer... - Replacement Wheel Studs for the Trailer Hub and Drum Assembly # AKHD-655-6-KThe wheel studs of the Trailer Hub and Drum Assembly # AKHD-655-6-K are 1/2 inch diameter. I checked with Dexter and the recommended replacement studs for this hub are the part # 165995.
view full answer... - How to Attach Spare Wheel/Tire to the Curt Trailer Hitch Mounted Spare Tire Carrier 31006If you are using the Aluminum Lynx Trailer Wheel part # LHSL311 then your trailer will have 1/2-20" lug studs therefore, in order to secure your spare wheel/tire to the Curt Trailer Hitch Mounted Spare Tire Carrier part # C31006 I recommend using multiples of the Wheel Stud part # 165995 and the Chrome Trailer Wheel Lug Nut part # 12CLN-L. The lip on the lug stud should be sufficient to attach to the plate so additional washers will not be needed. If you were ever to break a lug stud or...
view full answer... - What Grade are Redline Wheel Studs # 165995Yes, the six radial lines or markings on the top of the head indicate that the Drive In Wheel Stud 1/2" x 2-1/2", # 165995 is in fact a grade 8.
view full answer...
- Stud Installation on Dexter Axle Trailer Hub Assembly # AKIHUB-440-2-1KI contacted our representative at Axle Tek and he informed me that the studs on the Trailer Hub Assembly, part # AKIHUB-440-2-1K are Drive In Studs, so they are either pressed or hammered in. This hub assembly will work with your 2000 lb Axles, 4 on 4 bolt pattern, with L44643 Bearings. I informed him that you are planning to remove the studs and replace them with longer studs. He recommended Wheel Stud, part # 165995, which is about a 1/2 inch longer than the studs on part # AKIHUB-440-2-1K. To...
view full answer... - Replacement Wheel Studs for Hub 22834According to the information that I was able to obtain for hub 22834, it more than likely uses Drive In Wheel Stud, # 165995, which measures 1/2 inch x 2-1/2 inch. The absolute best way to determine the correct replacement wheel studs for your hub would be to hammer out one of the existing studs and take a measurement. I have included a link to all of the wheel studs that we offer for your convenience.
view full answer...
- Availability Of A 1/2 Inch Wheel Stud That Is 2-1/2 Inches LongThe only 1/2" x 2-1/2" long wheel studs we offer are the: - Wheel Stud # 165995. These are drive-in wheel studs that are 1/2" in diameter, have 20 threads per inch, and are grade 8 rated. You'll also want to measure the diameter of the splines, the length of the splines, as well as the overall length of the stud.
view full answer... - Longer Wheel Studs Needed for Dexter 2,200 Lb Trailer HubIn order to install longer lug studs on the Trailer Hub Assembly part # 8-258-50UC1-EZ you will need to use the Drive In Wheel Stud part # 165995 which are 1/2" longer. These new studs should then allow you to retain the wheel spacers therefore provide clearance from the fender. In order to install the new lug studs, we first need to remove the old ones which can be done by carefully hitting the top of the stud with a hammer. Then once the old studs are removed we can install the new ones....
view full answer... - How To Replace A Broken Wheel StudWhen finding replacement wheel studs you would have to measure them with a digital caliper like The 4 inch Carbon Fiber Digital Caliper # PTW80157. I will attach a diagram with the measurements needed to get the correct wheel studs you would need. Once you can provide me the measurements of A, B, C, D, E, and F I will be able to get you the correct replacement. For example The Wheel Stud - Drive In 1/2 inch x 2-1/2 inch (Qty. 1) # 165995 measures 1/2 inch diameter and is 2 inches long....
view full answer...
- Replacement Drive-In Wheel Stud for Hub and Drum Assembly for 5K/6K E-Z Lube Trailer AxlesFor a replacement drive-in wheel stud for hub and drum assembly # 8-201-9UC3-EZ you will need to use stud # 165995. This drive-in stud is 2-1/2 inches long.
view full answer... - Replacement Wheel Stud For A Aljo Travel Trailer The closest option I was able to find is the Wheel Stud # 165995 which measures 2-1/2" long, is 1/2" in diameter, and has 20 threads per inch.
view full answer... - Are All 1/2 Inch Lug Studs Fine Thread 20 Threads Per InchThe majority of drive-in lug studs like part # 165995 use a fine thread but only a 1/2"-20 tpi (threads per inch), not a 1/2"-32 tpi. I am not aware of any lug nuts we offer that will fit a 1/2"-32 tpi but what you can do is measure the bolt you have now to see if there are in fact 32 threads per inch as opposed to the much more common count of 20 threads per inch. If you do have 1/2"-32 tpi bolts then you will need to go to the hardware store in order to find a compatible nut but if you...
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Adam R
Installed by:
Jeff D
Updated by:
Adele M
Updated by:
Laura H
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Donald P.
4/15/2022
Perfect. No issues and the ONLY place I was able to find the lug!