Customers compare MCL914R1PG to these similar products
Products Featured in this Video
Speaker 1: Today we're gonna take a look at the Optronics Identification Light Bar for trailers over 80 inches wide. This is going to be a waterproof light that's going to be designed for trailers that again are wider than 80 inches. This is going to surface mount to your trailer. It has two holes on either side so you can bolt that into place. This is going to be DOT approved and it… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
I recommend using the etrailer Trailer Hitch Receiver #e38KR on your 2023 Kia Sportage. This receiver has a 2" x 2" opening and uses a hidden cross tube for a factory appearance. The T-One Vehicle Wiring Harness #TK32VR uses factory style…
view full answer...While Draw-Tite has confirmed that the Max-Frame Trailer Hitch Receiver #DT22MR will fit your 2023 Kia Sportage we have not had one in to install in our facility for images. I reached out to Draw-Tite and they confirmed that there is no additional…
view full answer...The Putco Red Blade LED Tailgate Combination Light Bar part #P92010-60 which is the lightbar I recommend for your trailer has LED lights so the amp draw will be very minimal. The reason that this is important is because the total amp draw for each…
view full answer...You will first want to check the fuses on your tow vehicle. Some vehicles could have fuses for operating the turn signals and brake lights of a towing package. You will want to check if they are installed and working properly. The next thing is to…
view full answer...The lights will need to be replaced, we have some great options for this. The Optronics LED Combination Trailer Tail Lights part #TLL160RK looks to be a great match for your existing taillights and the Custer Trailer LED Clearance Identification…
view full answer...Yes, the 7-Pin Round connector is wired differently than the 7-Way flat RV connector. I will list the typical heavy duty truck wiring connections inside the plug on the trailer side for you. At the index guide for plugging the trailer end in to the…
view full answer...I attached a picture that shows the pin out diagram for the Pollak 5th Wheel / Gooseneck T-Connector with 7-Pole #PK11893-11932 that you referenced.
view full answer...The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I have include…
view full answer...It's a wire color difference but not a function difference on the pins of the 7-way. The difference comes from the fact that the two different styles are representative of two different areas that uses trailers. Traditional is usually seen on…
view full answer...I think you are going in the right direction. I would definitely replace the 14 gauge wire going to the trailer brake magnets with 10 gauge wire or larger. Usually larger than 10 gauge is hard to get into the trailer connector though. I would also…
view full answer...The reason that 10 Gauge #10-1-1 or 12 Gauge #12-1-1 wire is recommended for 10" brake assemblies, like part #AKEBRK-35-SA, is because they pull more power than the lights on your trailer. I believe the green wire you are referring to carries…
view full answer...The Optronics Grommet #A91GB that you referenced, which is designed to work with the Thinline LED #AL91RB that you were looking at, will install into a mounting hole on the trailer that is 2-7/8 inches across and 1-1/2 inches tall. If you do not have…
view full answer...