Pollak 7-Way # PK11893-11932 Wiring Diagram

Question

Question:

I recently purchased this item from you. Watching the videos it mentions a picture on the product detail page showing the pin out for the bare wires. I dont see it on your page. Can you send to me please or link to it on your website? Thanks,

asked by: Rodney L

0

Expert Reply:

I attached a picture that shows the pin out diagram for the Pollak 5th Wheel / Gooseneck T-Connector with 7-Pole # PK11893-11932 that you referenced.

expert reply by: Jameson C

0

click to enlarge

Answer 1

No, they can not! The B&W Universal Base Rails item #BWRVR3200 and any other comparable set of rails will not be compatible with a preinstalled gooseneck hitch. I do have quite a few options to potentially add some 5th wheel rails using an…

view full answer...

Answer 2

I have added a photo detailing the wiring connections for the Pollack Heavy-Duty, 7-Pole, Round Pin conncetor, #PK11700, see link. This is a SAE J560 compliant connector. The wiring diagram for the vehicle side connector, #PK11720, is pictured…

view full answer...

Answer 3

The Pollak Black Plastic, 7-Pole, RV-Style Trailer Connector - Trailer End #PK12706 will match the colors and locations of the attached photo. I've also attached a wiring article to assist further if the colors don't match functions…

view full answer...

Answer 4

The black wire of the #PK11893-11932 does carry the 12 volt power circuit. This circuit is a 12 gauge wire. The standard amperage rating for 12 gauge wire is 41 amps typically, but this harness has a 30 amp rating. I attached a diagram that has a…

view full answer...

Answer 5

I have the perfect option for your 2019 GMC Sierra 2500 that will not require you to use an extension harness in order to connect the lighting on your gooseneck trailer. For this, I recommend the 5th Wheel/Gooseneck 90-Degree Wiring Harness part…

view full answer...

Answer 6

Look in the bed of your 2012 Ford F-250. Do you see 4 holes cut in the bed around the center of it? If so then you have the factory rail kit. If not then you do not have it. If you do not have it then you would want the part #BWGNRK1111-5W for the…

view full answer...

Answer 7

Thanks for the pictures! The plate you are needing to get behind is for your gooseneck ball in bed hitch. You will have to remove that to reach the bolt. This will allow you to install the Firestone item #F2703 air bags on your 2012 Ford F-250. I…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

The B&W Custom Underbed Installation Kit #BWGNRK1111-5W that fits your 2012 Ford F-250 Crew Cab Short Box installs on the outside surfaces of your frame rails. Any suspension kit that also installs on the outside of the frame will not work, but…

view full answer...

Answer 10

Yes, the 7-Pin Round connector is wired differently than the 7-Way flat RV connector. I will list the typical heavy duty truck wiring connections inside the plug on the trailer side for you. At the index guide for plugging the trailer end in to the…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

On the back of the Pollak 7-Pole, Round Pin Trailer Wiring Socket - Vehicle End, part #PK11720, it is marked alongside the pin with the color of the wire that connects to that pin location. I am also including a photo that will show a 7-Way round pin…

view full answer...

Pollak 7-Way # PK11893-11932 Wiring Diagram

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching