Size of Mounting Hole Required for Installing Optronics Grommet # A91GB
Question:
What size mounting hole for the Optronics A91 rubber mount for marker light?
asked by: Bryan H
Expert Reply:
The Optronics Grommet # A91GB that you referenced, which is designed to work with the Thinline LED # AL91RB that you were looking at, will install into a mounting hole on the trailer that is 2-7/8 inches across and 1-1/2 inches tall. If you do not have this type of mounting hole on your trailer, you can use the Mounting Bracket # A91BOB instead, which will allow for a surface mount installation.
I have attached a couple short video demonstrations on these products that you can also check out.
Products Referenced in This Question
Mounting Bracket for Optronics A91, AL82, AL90, AL91, or AL191 Series Lights - Open Back - Black
- Accessories and Parts
- Trailer Lights
- Mounting Hardware
- Brackets
- Black
- Optronics
more information >
Thinline LED Clearance and Side Marker Light - Submersible - 3 Diodes - Rectangle - Red
- Trailer Lights
- Clearance Lights
- Rear Clearance
- Side Marker
- Rectangle
- Surface Mount
- Submersible Lights
- LED Light
- 2-1/2L x 1-3/16W Inch
- Red
- Optronics
more information >
Product Page this Question was Asked From
Grommet for Optronics A91, AL82, AL90, AL91, or AL191 Series Trailer Lights - Black PVC
- Accessories and Parts
- Trailer Lights
- Mounting Hardware
- Grommet
- 3-5/16 Inch Long
- Rectangle
- Optronics
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Thinline LED Clearance and Side Marker Light - Submersible - 3 Diodes - Rectangle - Red
- Shop: Right Angle 2-Wire Pigtail for Optronics Trailer Lights - 2-Prong PL-10 Plug - 6" Lead
- Shop: Dexter Trailer Hub & Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Shop: Mounting Bracket for Optronics A91, AL82, AL90, AL91, or AL191 Series Lights - Open Back - Black
- Shop: Optronics Trailer Reflector - Adhesive Backing - Rectangle - Red
- Shop: 2-Wire Pigtail for Optronics Trailer Lights - 2-Prong PL-10 Plug - 18" Lead
- Video: Optronics Trailer Light Right Angle 2-Wire Pigtail Review
- Shop: Grommet for Optronics A91, AL82, AL90, AL91, or AL191 Series Trailer Lights - Black PVC
- Video: Hopkins Wiring - Wiring Adapters - HM47075 Review
- Video: Optronics Trailer Lights - Clearance Lights - AL91RB Review
- Video: Optronics Thinline LED Clearance and Side Marker Light Installation
- Q&A: Troubleshooting LED Identification Light Bar With Lenses Easily Knocked Off
- Q&A: Recommended Side Marker Lights for EZLoader Trailer
- Q&A: Replacement Trailer Clearance Light for PM150
- Video: Optronics Trailer Lights - Reflectors - RT10RB Review
- Q&A: What Hardware is Best for Mounting Trailer Light Mounting Bracket to the Trailer Surface
- Video: Optronics Lights Mounting Bracket Installation
- Video: Optronics Trailer Lights A91BOB Review
- Article: Trailer Wiring Diagrams
- Q&A: Why is 10 or 12 Gauge Wire Recommended for Electric Brake Assemblies
- Shop: Vehicle Lights
- Q&A: Wiring Pigtail and Mounting Bracket Options For Installing Thinline LED Clearance And Marker Lights
- Q&A: What is the Proper Gauge Wire for Installation of a Brake Controller and Trailer Brakes
- Shop: Trailer Wiring
- Shop: Vehicle Tow Bar Wiring
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Search Results: wesbar side marker light
- Search Results: trailer fenders
- Search Results: fa1131822
- Search Results: knott