Customers compare MA00-04000K to these similar products
Products Featured in this Video
Today we're going to be taking a look at the Max Air Max Fan trailer roof fit with a 12 volt fan. The reversible, variable speed fan is going to allow you to precisely control air movement in and out of your RV. This can be used as a ceiling fan. Basically, all you have to do is close the lid. This is designed to operate while the lid is closed and that's really going to help circulate air inside… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
Good morning, Don. The 3/4" wide butyl tape is exactly what we recommend for installing a roof vent such as the MaxxFan #MA00-07000K. We actually sell a roof vent install kit part #344270KITW that comes with sealant, screws and a 30'…
view full answer...The amperage draw of the motor that comes with the Ventline roof vent motor part #V2094SP-28 is 1.2 amps at 13.6 volts.
view full answer...The most similar solution we offer would be the MaxxAir part #MA00-04000K which has a white lid, manual lift, and a 12 volt fan, but we do not have a Fan-Tastic roof vent that has a white lid.
view full answer...Check your power source, ensure you have voltage to your MaxxFan, MA00-04000K. Use a voltmeter to ensure your battery is delivering the required voltage (no less than 11-volts). If this is a new install please verify that you connected wiring…
view full answer...The replacement vent cover for your Sundowner horse trailer can be different as vents are often changed over the years by manufacturers. The vent cutouts remain consistent because there is an industry standard size so replacements are available but…
view full answer...It looks like your Sundowner roof vent is a standard 14 x 14-inch size with a continuous-type hinge. For such a vent we offer the Ventline Vent Cover for Old Style Rounded Dome Trailer Roof Vents #BV0554-03 (smoke) and #BV0554-01 (white). We also…
view full answer...The Dexter 31549 axle on your snowmobile trailer is a 3,500 lb torsion axle. Although we do not carry torsion axles, you can use the Timbren Axle-Less Trailer Suspension #ASR3500S05. This is very similar to your current axle with each side working…
view full answer...To install the Curt Friction Style Sway Control System, part #17200, to your trailer will require drilling holes in the trailer frame. Drilling the few holes that are needed in the side of the tongue for installation of the sway control will not…
view full answer...All of the friction sway control units like the Curt #17200 that you referenced require drilling into the trailer frame. We do have electric sway control units like the Tuson part #335TSC-1000 which uses sensors to detect trailer sway and apply the…
view full answer...We do have a few options to choose from, we have the MaxxAir II and Trailer Roof Vent Cover w/E-Z Clip #MA86JR which is black in color and will fit your standard 14" x 14" roof opening. We also have #MA76JR which is the same cover…
view full answer...The MaxxAir FanMate vent cover Item #MA00-955001 is going to be just a little taller but the louvred end tapers in and it does not come with the screen which is Item #MA00-955202. 25" long x 18-1/8" wide x 10-1/4" tall. The…
view full answer...The LaSalle Bristol XTRM Self-leveling Sealant part #34427034145-1 is very comparable to the Dicor 501LSW self leveling lap sealant. I can't say exactly what the formula is for Dicor but I can tell you that LaSalle Sealant is a silicone…
view full answer...