Ventline Ventadome Trailer Roof Vent - Manual - 14-1/4" x 14-1/4" - Smoke
(316 reviews)
Price: $61.79
In Stock
Ventline Ventadome Trailer Roof Vent - Manual - 14-1/4" x 14-1/4" - Smoke
Item # V2092SP-29
Our Price: $61.79
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (316)
- Q & A (0)
- Photos
Ventline RV Vents and Fans - V2092SP-29
- Vent
- Roof Vent
- No Fan
- 14W x 14L Inch
- Tinted
- Ventline
- Manual Lift
- 4-1/2 Inch
- Plastic and Metal
This roof vent allows air to circulate in motor homes and enclosed trailers, keeping interiors ventilated without compromising security. Wedge-shaped, smoke-colored plastic vent cover opens and closes from inside with a hand-operated crank.
Features:
- Roof vent allows fresh air to enter, and heat to escape, while trailer or RV remains locked and secure
- Simple, hand-operated crank rotates to open and close dome and eliminates the need for wiring
- Translucent cover allows some light through
- Aerodynamic, wedge-shaped dome made of durable polypropylene
- Galvanized steel roof flange won't rust or corrode
- Snap-out screen is easy to clean
- Polar White interior trim piece (or garnish) is included
- Made in the USA
Specs:
- Included garnish fits roofs 1-7/8" to 3" thick
- Garnish leg length (depth): 2-1/8"
- Garnish color: Polar White
- Other garnish sizes are available (sold separately)
- Cover color: Smoke
- Rough opening size: 14-1/4" wide x 14-1/4" long
- Measurement of metal lip of vent: 16-1/2" x16-1/2"
- Garnish measurements: 16" x 16"
- Vent extends above roof:
- 4-1/2" Closed
- 10-3/4" Open
- 2-Year limited warranty
Note: Screws and sealer are not included. See Installation Kit (344270KITW), which includes all necessary screws and sealer to install vent.
Installation Instructions
- Mark desired location for vent. Be sure to choose a location between roof joists.
- Cut a 14-1/4" x 14-1/4" opening through roof and ceiling. (Or use existing opening if you're replacing a standard 14-1/4" x 14-1/4" vent.)
- Apply sealant to bottom of flange. Be sure to surround each screw hole.
- Insert vent through hole with screen frame extending through roof cavity and hinge of vent toward the front of the vehicle.
- Mount to roof with #8 screws.
- Attach interior garnish piece with #8 screws.
V2092SP-29 Ventline Ventadome Trailer Roof Vent - Manual - 14-1/4" x 14-1/4" - Smoke
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- Arrived Damaged
Customer Reviews
Ventline Ventadome Trailer Roof Vent - Manual - 14-1/4" x 14-1/4" - Smoke - V2092SP-29
Average Customer Rating: 4.7 out of 5 stars (316 Customer Reviews)
This roof vent allows air to circulate in motor homes and enclosed trailers, keeping interiors ventilated without compromising security. Wedge-shaped, smoke-colored plastic vent cover opens and closes from inside with a hand-operated crank.by: Ron01/09/2024
So far it's holding up with no leaks. Kind of on the flimsy side comparing to the one removed but easy to install. Couldn't use the trim ring inside but after a year still looks new and the lifting/lowering mechanism works smoothly. Overall a good price for the quality.
by: Mark12/11/2023
Purchased this because from Etrailer because they state made in USA. Nowhere is there a made in USA stamp or in print. It looks identical to the made in China ones for $[XX] cheaper on [online resale]. By the build quality I am quite sure that it is Disappointed to say the least
by: H Mackay09/05/2014
Installed this vent into my Haulmark Transport 6'x12' enclosed trailer. Installation was easy, I cut a 14.25" x 14.25" inch hole between two crossmembers in the roof and dropped it in place. Because the roof on this enclosed trailer is so thin, I used a piece of 3/8" plywood so sandwich between the interior garnish and actual vent. I cut the same size hole into the plywood and left a 2" lip all around. I use 28 #8 x 5/8" stainless screws to hold it in place, pre-drilled with 1/8" bit. I then used roofing tar to seal the vent and put masking tape all around, leave 1" from the flange to ensure good coverage. I then removed the masking tape, leaving nice clean lines. Interior garnish is held in place by #8 x 3/8" galvanized screws.
Huge kudos to etrailer for carrying such awesome products for great low prices and offering super cheap shipping to Canada!
by: Jerry Kramer08/16/2017
My truck build; I have developed, invented, a new kind of truck cap and also wanted to provide the best venting in the industry and this is why I wanted this product. Although it is a little flimsy it is easy to install and easy to use. And it adapts well for my use. My product (I hope to have available in good stores like Etrailer by years end) is a rigid, folding, adjustable (fits most trucks), one person on & off, and easy to store when off pick up truck cap or camper. See attached photos of my prototype build. Many have inquired to use it for their pets, for camping, and many other uses.
by: Doug12/27/2021
Very pleased with product and the fast cheap delivery.Also liked that the size stayed the same all these years it fit the opening of my old vent in my 1978 classic van
by: BrianB.09/09/2019
Learned my lesson, not to go cheap! I bought a $20 dollar vent online less a year ago, and the Arizona heat disintegrated it. I called Noah at eTrailer and he was fast, knowledgeable, and courteous. The new vent arrived within a few days and it installed in less than and hour without a problem. Most of the work is in the prep. If you've never done this before, follow the instructions in eTrailer's video, and you won't have any problems. If you need to trim the garnish ring, I snipped it vertically at either side of the corners and then bent the plastic, snapping it like tile or drywall. Easy-Peasy! I really like the smoke tint to, I can see the sky through it. Thanks for the suggestion Noah!
by: Mick 04/25/2024
Arrived sooner than expected. Exactly what I ordered. Thank you!
by: Gregory 07/08/2023
This was an easy drop-in replacement for a broken OEM vent. Well-made, although its usable life in a high-altitude, high-UV western-Colorado environment is yet to be proven. But if anything this vent was better-made than the OEM item. I have no reservations about recommending it to other DIY RV owners.
by: Matthew02/08/2024
No more leaky roof!
by: Gary04/05/2013
Was a replacement for another ventline taken out by hail. Item was as presented, price was right shipping was prompt. Will use terai let again if need arises
by: David09/18/2022
I used this vent to replace an older static vent in our high top camper van. The installation and instructions were OK, and the vent opening mechanism works fine. The issue is that the top cover is too flexible, and it always flapped in the wind. I purchased a replacement cover from [online company], which is thicker, stronger with more reinforcing ribs. It works fine. Overall a good product with a flimsy top cover.
by: Paul07/28/2016
This product is a wonderful addition to our travel trailer.
Since we installed the one vent and another vent with the fan we have
not had any problems with them. Great products !!!
I would like to mention that the colored covers let in more light then
the old white cover.
Paul
7/28/2017
Great. Still looks and works like it should.
by: Tom 02/22/2023
This vent was exactly what I needed. The original had been broken and the replacement from etrailer was a perfect fit and the quality was better.
Thank you etrailer
by: Yvette09/26/2023
fit like a glove
by: Steven H.02/15/2013
UPS has a new habit of delivering to my Post Office. So when I get there, 25 miles round trip once a week I was surprised to find your package there. So the question, why pay for UPS shipping if they are not going to deliver and it cost me additional money just to drive to the Post Office?
The product (vent) is nice, shipping could throw a piece of foam on the bottom of the box so the plastic dome does not get all marred up in the box..
Steven H.
8/16/2014
still working and traveling the country
by: Melvin07/24/2022
Looks terrific, as described. Only wish the done were a little less flimsy. The product fit & looks perfect however the plastic dome could have been a little thicker plastic
by: Wade 08/31/2023
Great service once again, thanks!
by: Coleen S.07/09/2016
This vent was shipped fast and received within a week after. I was contacted by a customer rep to make sure I was satisfied or had any questions. Vent went in quickly and easily. Instructions were clear and I had no trouble understanding what was required. This was the first time I had done anything like this on my travel trailer and am extremely happy with the results. I would order from etrailer.com again in a heartbeat. Great product-Great customer service. Thank you, George J.
Coleen S.
7/9/2017
After 1 year I am still extremely satisfied with the vent. It is functioning as it should and I have had no problems with it at all.
by: Larry j04/07/2015
Pretty solid to be so light weight, UPS beat the hell out of it in route. If it only came with a gasket like the original I removed :-( Fit and function Good, the original lasted 19 years and the plastic dome was still in tact with no leaks, the mechanism broke. 2 Tubes of Hi quality Permatex engine sealer and I hope for the best. I would be happy for 15 years of longevity. The old sealer was petrified from the UV and heat, came off like concrete. That gasket kept it sealed....
Patrick B.
4/15/2015
RTV Silicone makes for an excellent gasket material if you are mounting flat surfaces. Follow the perimeter all the way around, encircle the hardware holes, and attach the vent. Once it cures, it creates a gasket between the two surfaces. For extra waterproofing, you can come back with silicone caulk and cover the heads of the screws and run a perimter bead around the vent.
by: Jake H05/01/2016
I replaced the old vent on a 1983 tent trailer. This vent is twice the size of the original one so there was some cutting and modification of my roof involved but the vent works great. I also got the loctite vent install kit that comes with the sealant and screws to install the new vent. It was a great help for a he install. My roof hasn't leaked since last year.
by: Christopher 06/27/2023
Simple and low cost, does the trick!
by: MAUREEN06/05/2017
Products, VENTLINE roof vent for my FORD Econoline and WEATHER TECH window Deflectors, arrived in good condition. I needed to get some air to the back of the van, as it will be used for camping, think this will do the trick. Then I have been interested in trying out deflectors for a long time as well, wanted to be able to get better air circulation without the road noise. All contact was very positive and I would order from you again as well as tell others.
Installation will occure on June12, so will let you know how that goes. It was all a very good experience.
MAUREEN
by: Richard 08/22/2023
Good product..
by: Milton 08/24/2023
Quality product from a quality company.
25
316
Show More Reviews
See what our Experts say about this Ventline RV Vents and Fans
- 14 Inch Roof Vent with and without Fan Recommendation for 1-1/2 inch Thick RoofFor just a 14 inch roof vent the part # V2092SP-29 would be a great option. This will fit a 1-1/2 inch thick roof if you get the garnish part # VA0445-25 or trim down the included one. For a model that includes a 12 volt fan you would want the part # V2094SP-28 instead.
view full answer... - Will Ventline Ventadome Roof Vent Fit 14 inch by 14 inch Square Opening on TrailerThe Ventline Ventadome Trailer Roof Vent # V2092SP-29 will fit your trailer that has a 14 inch roof opening. Worst case scenario you'd have to open up the opening on your roof a little bit but even that most likely wouldn't be necessary. This vent is designed for that standard roof opening size that's between 14 and 14-1/4 inch square.
view full answer... - Replacement Roof Vent Recommendation for Fuzion Toy Hauler with AS-13 M-VDO449 on LidWe have had a similar question to this come up and we were able to determine that the number AS-13 M-VDO449 that you listed is stamped on the vent cover part # BVD0449-A01. If you are looking for the entire fan setup and not just the cover you would want the part # V2092SP-28 for a white lid or part # V2092SP-29 for a smoked lid. The smoked lid would allow more light in.
view full answer... - Solutions To Keep A 6x12 Enclosed Trailer CoolI recommend installing a standard manual lifting roof vent, like the Ventline Ventadome Trailer Roof Vent # V2092SP-29 for a smoke color, or # V2092SP-28 for a white color. I suggest also adding the MaxxAir Standard RV and Trailer Roof Vent Cover # MA00-933066. which will allow you to keep your vent open while keeping out rain and water. To take it a step further, you can also install the 2-Piece Polypropylene Trailer Vent for 3" Diameter Hole # WHMAV2-WAVT2 lower on the trailer to create...
view full answer... - Vent Cover Replacement For 2014 Lark 5 x 8 Enclosed TrailerFor a replacement trailer roof vent cover you will want to measure the vent itself. For selecting a new vent assembly to install in the trailer you will want to measure the dimensions of the roof opening. Most often square-shape trailer roof vents are 14 x 14-inches in size and fit into a roof opening of 14-1/4 x 14-1/4-inches. Examples of this popular vent size are the Fan-Tastic Vent fan-powered vent # FV801250 and the non-powered Ventline # V2092SP-29. When selecting just a replacement...
view full answer...
- Availability of RV Roof Vent Replacement with Part Number VDO434That part number matches a Ventline Ventadome roof vent like the part # V2092SP-28 which has a white lid or part # V2092SP-29 which has a smoked lid.
view full answer... - Recommended 14 x 14-Inch Ventline Roof Vent for 1998 Sun Lite Pop Up Camper TrailerA 14-1/4-inch x 14-1/4-inch rough trailer roof opening is very common and we offer a whole range of complete vent assemblies and also replacement lids and other parts for this size vent. Vents that fit this opening size are 14 x 14 size and the linked page will let you see all that we offer. These include both manual and powered types, plastic-domed vents in various colors and also metal vents. For instance, if you prefer a smoke-color manual vent you could use Ventline # V2092SP-29. If...
view full answer... - Replacement Roof Vent Cover for Lid Marked AS-13M-VDO449 ANS Z26 1We have had a similar question to this come up and we were able to determine that the number AS-13 M-VDO449 that you listed is stamped on the vent cover part # BVD0449-A01. If you are looking for the entire fan setup and not just the cover you would want the part # V2092SP-28 for a white lid or part # V2092SP-29 for a smoked lid. The smoked lid would allow more light in.
view full answer...
- Roof Vent Recommendation for a 1981 Jayco Tent TrailerNothing we have would fit the hole size in your trailer, but if you would be willing to enlarge the hole to 14-1/4 inch by 14-1/4 inch you could use the part # V2092SP-29. I attached a review video for this roof vent for you to check out as well.
view full answer... - Replacement Roof Vent for 1992 Palomino Filly Pop-Up CamperWe have many types of trailer roof vents and vent parts but we do not have a way to look up the vent originally installed in your 1992 Palomino Filly so I suggest confirming the dimensions. Most often square roof vents are 14 x 14-inches and fit roof openings that are generally 14-1/4 x 14-1/4. Based on photos of your pop-up that I could find it appears you do have a 14 x 14 vent so I linked for you our entire range of trailer vents in this size. We have manual vents, 12V powered vents...
view full answer... - Replacement Bathroom Vent Lid for 2010 Keystone SprinterSeveral things will determine the correct replacement vent dome lid. The manufacturer of the vent The size of the vent The location of the lift mechanism (on the side of the vent or in the center) The configuration of the hinge, continuous, three tab, etc. Closely examine the vent and the lid, looking for the manufacturer's name or a model number. If you click the link showing our replacement lids, you can use the filters on the side of the page to narrow down the results according to...
view full answer... - Install Kit for Trailer Roof Vent The install kit you mentioned is no longer available but we do have the LaSalle Bristol Kit # 344270KITW in White or # 344270KITB in Beige that will give you everything needed to install the Ventline Ventadome Roof Vent # V2092SP-29 that you were looking at. This kit includes two 10.1 oz tubes of sealant, a 60 foot roll of butyl tape, 8 wood screws, and 30 sheet metal screws. I have attached a sample install video that you can also check out.
view full answer... - Roof Vent Recommendation to Fit 14-1/2 inch Square OpeningA 14-1/4-inch x 14-1/4-inch rough trailer roof opening is very common and we offer a whole range of complete vent assemblies and also replacement lids and other parts for this size vent. Vents that fit this opening size are 14 x 14 size and the linked page will let you see all that we offer. These include both manual and powered types, plastic-domed vents in various colors and also metal vents. For instance, if you prefer a smoke-color manual vent you could use Ventline # V2092SP-29. If...
view full answer... - Solution for 13-1/2" Metal Roof Vent for Enclosed TrailerI do have a solution, but we do not have any vents that will fit your dimensions. I recommend enlarging the hole slightly and installing the Ventline Ventadome Trailer Roof Vent - Manual - 14-1/4" x 14-1/4" - Metal # V2110SP-24. We also have an option with a smoke lid # V2092SP-29 and white lid # V2092SP-28 available as well.
view full answer... - Recommended Translucent Dome Lid for a 2017 Palomino Puma Travel TrailerThe closest lid we have to a clear lid is the Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vent # BVD0449-A03 which is a translucent smoke color. This lid is a direct replacement for the Ventline Ventadome Trailer Roof Vent # V2092SP-29 so if this is what you have, it'll work great. If you're looking for something else, feel free to come back with a bit more info or maybe some pictures and I'd be happy to help.
view full answer... - Recommended Trailer Vent with Integrated Screen for 14x14 Inch VentUnfortunately we don't have the replacement screen for your assembly based on the photo. I recommend using the Ventline Ventadome Trailer Roof Vent - Manual - 14-1/4" x 14-1/4" - White # V2092SP-28 as a complete replacement as it is a very popular brand with the replacement screens if you should need it in the future. These vents are all a standard size that is referred to as 14 by 14 even though the rough opening is a 1/4 inch larger in both directions. If you prefer the smoke colored...
view full answer...
- Will Ventline RV Roof Vents fit Rough Cut Opening of 14-1/8 by 14-1/4 inchYes both of the vents you mentioned # V2092SP-29 and # V2094SP-34 can fit the rough openings of your RV that is 14-1/8 by 14-1/4 inch.
view full answer... - Does Ventline Ventadome RV Roof Vent Include Crank/Lift AssemblyAs you can see in the linked description and installation videos, the # V2092SP-29 Ventline roof vent does indeed include the manual lift assembly, as well as the interior trim, or garnish. It does not include the install kit, part # 344270KITW which is available separately.
view full answer... - Should Butyl Tape or Putty Be Used to Install New Trailer Roof Vent When installing a new roof vent like the Ventline Ventadome Trailer Roof Vent # V2092SP-29 I recommend using butyl tape like what is included in the Installation Kit # 344270KITW. Butyl won't dry out over time like traditional putty and it will help to create a better seal between the vent and roof. I have attached an installation video that you can also take a look at.
view full answer... - Which Trailer Vent Covers Let More Light Pass Through, White or SmokeThe smoke and white covers that are on the Ventline roof vents are both going to let quite a bit of light into the trailer. However, due to the translucent nature of the smoke covers they would let more light in. Both would last about the same amount of time. One has not been shown to stand up to the sun better than the other. For a smoke version of the part # V2094SP-30 that you referenced you would want the part # V2092SP-29.
view full answer... - Ventline Ventadome Trailer Roof Vent Recommendation for a 6x12 Enclosed Trailer for Gas FumesYes, the Ventline Ventadome Trailer Roof Vent # V2092SP-29 would fit the roof of your 6 x 12 enclosed trailer and would do a great job to get rid of the gas fumes that are building up in there from your equipment. I attached a review video for this product for you to check out also.
view full answer... - Roof Vent Replacement Recommendation for a Cargo TrailerThe # V2092SP-29 that you referenced has overall dimensions of 16-1/2 inches by 16-1/2 inches. This includes the metal lip around the outside of the vent. This vent is designed to fit a rough cut hole of 14-1/4 inches by 14-1/4 inches. This is a pretty standard size for a roof vent and is most likely what you have so it should work. But you will want to confirm by checking the dimensions of the roof of your cargo trailer. I attached a review video for this product for you to check out as well.
view full answer... - Replacement Vent for Enclosed Travel TrailerWhat you described does not sound like a vent system that we carry since none of our vents have tabs that protrude up on the corners. The best solution I could provide for you would be to replace your vent with one that we carry as long as the hole for the vent of your trailer isn't better than 14-1/4 inch by 14-1/4 inch. The # V2092SP-29 would work great
view full answer... - Will the Ventline Ventadome Trailer Roof Vent # V2092SP-29 Fit a 4 Thick RoofYes you can! The Ventline Ventadome Trailer Roof Vent # V2092SP-29 comes with a garnish that has a leg length of 2-1/8" and can accommodate a roof up to 3" thick. For your 4" thick roof you will simply want to use the Ventline Garnish # VA0445-35 which has a 3-1/8" leg. You will also need the Install Kit # 344270KITW which includes the hardware and sealer you need to complete the installation.
view full answer...
Do you have a question about this RV Vents and Fan?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Jameson C
Expert Research:
Adam R
Expert Research:
Lori W
Expert Research:
Jeffrey L
Written by:
Raymond P
Updated by:
Adele M
Updated by:
Kathleen M
Updated by:
Wilson B
Updated by:
Hannah L
Updated by:
Adam Y
Updated by:
Isabelle B
Video Edited:
Chris R
Installed by:
Robert C
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Doug
12/28/2022
Love it ,lots of compliment’s on look being it’s a classic van. Gave lots of fellow vanners the link