Ventline Ventadome Trailer Roof Vent w/ 12V Fan - Manual Lift - 14-1/4" x 14-1/4" - White
(1070 reviews)
Price: $156.94
In Stock
Ventline Ventadome Trailer Roof Vent w/ 12V Fan - Manual Lift - 14-1/4" x 14-1/4" - White
Item # V2094SP-30
Our Price: $156.94
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (1070)
- Q & A (0)
- Photos
Ventline RV Vents and Fans - V2094SP-30
- Vent
- Roof Vent
- 12V Fan
- 14W x 14L Inch
- White
- Ventline
- Manual Lift
- 4-1/2 Inch
- Plastic and Metal
This roof vent uses a 12-volt fan to circulate air in motor homes and enclosed trailers, keeping interiors ventilated without compromising security. Wedge-shaped, white plastic vent cover opens and closes with a hand-operated crank.
Features:
- Roof vent's electric fan yields better air circulation than non-powered models, exhausting hot air while trailer or RV remains locked and secure
- Simple to upgrade from non-powered model
- Basic, hand-operated crank rotates to open and close dome
- Switch to turn the fan on/off is mounted on the vent
- Translucent cover allows some light through
- Aerodynamic, wedge-shaped dome made of durable polypropylene
- Galvanized steel roof flange won't rust or corrode
- Snap-out screen is easy to clean
- Polar White interior trim piece (or garnish) is included
- Fan uses 12-volt DC power
- Wiring sold separately
- Made in the USA
Specs:
- Included garnish fits roofs 1-7/8" to 3" thick
- Garnish leg length (depth): 2-1/8"
- Garnish color: Polar White
- Other garnish sizes are available (sold separately)
- Fan power: 12-volt DC
- 100 CFM
- Cover color: white
- Rough opening size: 14-1/4" wide x 14-1/4" long
- Vent extends above roof:
- 4-1/2" Closed
- 10" Open
- 2-Year warranty
Notes:
- Screws and sealer are not included. See Installation Kit (344270KITW), which includes all necessary screws and sealer to install vent.
- Not for use above tubs, showers or range cooking surfaces.
Installation Instructions
- Mark desired location for vent. Be sure to choose a location between roof joists.
- Cut a 14-1/4" x 14-1/4" opening through roof and ceiling. (Or use existing opening if you're replacing a standard 14-1/4" x 14-1/4" vent.)
- Apply sealant to bottom of flange. Be sure to surround each screw hole.
- Insert vent through hole with screen frame extending through roof cavity and hinge of vent toward the front of the vehicle.
- Mount to roof with #8 screws.
- Remove screen frame and wiring compartment cover to make electrical connections.
- Connect to 12-volt DC power source
- Replace screen frame and cover.
- Attach interior garnish piece with #8 screws.
V2094SP-30 Ventline Ventadome Trailer Roof Vent - Manual Lift - 14-1/4" x 14-1/4" - White
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- Arrived Damaged
- Did not arrive in time
Customer Reviews
Ventline Ventadome Trailer Roof Vent w/ 12V Fan - Manual Lift - 14-1/4" x 14-1/4" - White - V2094SP-30
Average Customer Rating: 4.7 out of 5 stars (1070 Customer Reviews)
This roof vent uses a 12-volt fan to circulate air in motor homes and enclosed trailers, keeping interiors ventilated without compromising security. Wedge-shaped, white plastic vent cover opens and closes with a hand-operated crank.by: Brenda 03/09/2024
This fan has worked great for my motor home. If you need a stronger breeze, this may not be the fan for you.
by: Kevin 06/03/2023
Quick delivery and easy installation. My camper is a little older but this vent fan is an exact match. Bery happy with the removable screen for cleaning great feature the old vent didn’t have.
by: Jeff 10/18/2023
Perfect replacement. Quick shipping great customer service
by: Harley 0107/06/2012
I found this vent and fan combination to be just what I needed. I added it to the roof of my enclosed motorcycle trailer. It's made a big difference in keeping the inside of my black trailer cooler. Unless you have sheet metal screws and sealant around the shop, I'd order the install kit. This product does not come with a template for instilling it. I made my own out of thin plywood. Watch the edges of the metal, they are sharp.
by: Bob C04/30/2017
Ordered a Ventline Roof Vent, the total system from the top cap, shroud (extra deep), fan and ceiling fittings. Received promptly, everything as ordered, delivered promptly. Everything fit. ETrailer has become my primary parts source.
by: Danthecarpenter08/20/2015
Some reviews said this product was flimsy. I found it to be the same quality or bette than every RV vent that costs more than this one. The nice thing about this one is the screen is easily removable, unlike other RV vents I've used. The opening mechanism works as good or better than others. Overall I'm happy with the quality and operation of this vent.
by: John05/22/2021
Ordered ac seal,plumbing boots,bathroom vent and refrigerator vent covers. Descriptions of items were right on.
by: Kerry S10/23/2012
This item arrived when they projected it would. As always I'm very happy with the service and how quick they responded when I had a question. I will definately continue to give them my business. I have not yet installed the roof vent so I can't send a picture.
by: Jason D05/30/2017
Great little fan. It moves some air for being so little. Just wish I would've researched more as it turned out, I do need a bigger fan. Very easy to install however.
Jason D.
5/30/2018
Still good. Helps a bit with circulation when using a small electric space heater in my pop up camper.
by: Guy D.04/10/2018
Received vent fan in a timely fashion,product looks excellent.l will be using it in a food truck.
by: Rosco08/15/2017
I purchase a small 1985 travel trailer and the vent fan stop working. I search online for the best price, well this product review should tell everyone this item wasn't bought at camping world. etrailer.com has the best online prices and great DIY videos. Thanks.
by: ToddC10/06/2022
I loved that they were shipped the next day and arrived as promised. My installer only used the parts he needed. So, I now have a hybrid of old and new. But they work perfectly together, and I saved the spare parts.
by: Paul06/11/2022
Great replacement bathroom vent, better customer service.
by: William P.12/21/2015
This item was received in good order. Fantastic and I plan on doing more business with you in the spring.
Thank you so much
by: Diane11/22/2013
The product arrived exactly as expected and was easier to install than expected. With the excellent pricing, this is our new RV parts store. Thanks!!
by: Rodney01/15/2019
Great vent for the price. Replaced due to hail damage. Seals nicely and lets a good amount of light through. Smooth operation opening and closing.
by: patrick D.07/10/2015
Shipped quickly, arrived in perfect condition. Customer service was outstanding. So nice to be able to talk with a real person and one who is so customer friendly.
Patrick D.
7/29/2016
When we need anything for the RV we will definitely buy from you, thanks for excellent service and products.
by: Jeffrey L E09/10/2013
Good quality. 12V fan is small but moves air well. Also is quieter than the original unit it replaced.
by: Good04/21/2017
Good quality. Needs to be packaged better. Vent flange was bent in a couple of places during shipping.
by: Daniel06/29/2018
Rest assured, most aftermarket parts you buy to repair you rv with, are much better quality than the cr#p the manufacturers build with.
by: jeff d07/29/2016
same as original that was damaged by hail. still required putting and additional cover over this product to prevent future damage
by: Faye07/31/2021
Been in the camper for a year now and no leaks. Product is excellent . When done looked professional done .
by: Joel h.09/15/2018
we installed the vent and it seems to be doing a great job.... we have no complaints about the product or the service
by: M Davis 04/12/2015
Exactly as our old vent. Easy to install. Product shipped immediately. Company sent emails updating delivery. Completely satisfied.
by: Jim Nn11/21/2017
Very happy with entire process. Good selections, courteous sales staff. Had pleasure in ordering parts Sales people were helpful and made the whole thing enjoyable. Yours Respectfully, Jim N.
25
1060
Show More Reviews
See what our Experts say about this Ventline RV Vents and Fans
- Replacement Continuous Hinge Vent CoverThanks for the photo and based on that it looks to me like you may have had a continuous hinge and would need the Vent Cover for Ventline Old Style Rounded Dome Trailer Roof Vents - White # BV0554-01, though you are going to want to confirm this is the hinge style you have. If not you can also go with the MaxxAir UniMaxx Universal Replacement Lid # MA00-335001. As for the lift arm, for that you would need to know the manufacturer to get the correct one. For example, if you had a Fan-Tastic...
view full answer...
- Vent Fan for a Cargo Trailer ConversionWe have the Ventline Roof Vent w/ 110V Fan # V2128SP-01 which fits a 14-1/4" wide x 14-1/4" long opening and roofs that are 2-1/8" to 3-1/4" thick. It is a 110v fan, there is not a 120v fan option. If the 110v option does not work for you, we also have it in a 12v option. - Ventline Ventadome Trailer Roof Vent w/ 12V Fan # V2094SP-30 (Fits 1-7/8" to 3" thick roofs)
view full answer... - Will the Ventline Ventadome Trailer Roof Vent # V2094SP-30 Work with a MaxxAir Roof VentYes, as long as the MaxxAir Vent Cover you have on your trailer is MaxxAir II then the Ventline Ventadome Trailer Roof Vent # V2094SP-30 would work well with it as this is the size vent the # 67277 was designed to fit.
view full answer... - Replacement For Ventline Trailer Roof Vent V2094To replace your Ventline V2094 trailer vent fan, use the following: - Ventline Ventadome Trailer Roof Vent w/ 12V Fan # V2094SP-30 This includes a garnish which fits roofs 1-7/8" to 3" thick, but if you have a roof with a different thickness use # VA0445-35 for 2-7/8" to 4" thick roofs, or # VA0445-37 for 5-1/8" to 6-1/4" thick roofs. If you need install materials use Roof Vent Installation Kit # 344270KITW.
view full answer... - Replacement Screen for Ventline Northern Breeze VentI do have an option for you but the Replacement Bug Screen part # FVK2034-80 is not correct for your Ventline Northern Breeze Vent nor is the correct replacement available as it has been discontinued by the manufacturer. The only option we can offer you is a new unit, the Ventline Ventadome Trailer Roof Vent part # V2092SP-28 or part # V2094SP-30 with fan. These units will however be a direct replacement for the Northern Breeze Vent you have now. The screen is also replaceable using the...
view full answer... - Can the Ventline Ventadome Trailer Roof Vent be Installed in a 1 Inch Thick RoofAfter inspecting roof vent # V2094SP-30 and the included bezel, I have come to the conclusion that you would just need to trim 13/16 of an inch off the bezel on the end that sticks into the vent. This should allow you to flush mount the vent and bezel in your 1 inch thick roof. I also recommend installation kit # 344270KITW which comes with the hardware, tape, and sealant needed for installation.
view full answer... - Availability of Replacement Parts for Ventline Rounded Dome Trailer Roof VentThe Ventline product you reviewed, part # V2092SP-28, is a complete vent assembly intended for a rough roof opening of 14-1/4 x 14-1/4 inches. It consists of a wedge-shaped white plastic dome attached to a galvanized steel frame with hand-crank assembly, a removable screen, and a white plastic 2-1/8-inch-deep garnish (interior trim ring). Please note that this part requires an installation kit, part # 344270KITW, which consists of mounting hardware and a urethane caulk sealer. If your...
view full answer...
- Can a Larger Fan be Installed in the Same Housing as Old Van on Ventline VentadomeThe guts of a higher capacity fan would not fit in Ventline vent # V2094SP-30 without fairly extensive modification so I do not recommend it. The best solution would be to remove the vent assemblies and install newer, higher capacity options. Fan # FV802250 for example has a larger fan and moves air up to 920 cubic feet per minute which is more than twice what the Ventline Northern Breeze can put out. I have linked a video review for you.
view full answer... - Replacement Screen for Ventline Vent V2094The Phillips V2094 you referred to is the same as the Ventline Ventadome # V2094SP-30 and we do carry screens for this vent, in two colors. The part number for Birch White is # BVC0573-31 The part number for Polar White is # BVC0573-41 These include the screen frame and screen; I've added links to video reviews of both parts for you to take a look at.
view full answer... - Can A Fan Be Added To A Ventline Ventadome Trail Roof Vent Without A Fan If you're talking about adding a fan to the Ventline Ventadome Trailer Roof Vent # V2110SP-24 then no, you wouldn't be able to add a fan and would need to purchase a vent that already includes a fan like the Ventline Ventadome Trailer Roof Vent w/ 12V Fan # V2094SP-30. You can splice into the 12v power that's already there to power this vent and make the installation easier. To complete the installation you'll also need some butyl tape # AL28FJ and self-leveling sealant # 34427034145-1...
view full answer... - Can Manual Crank Vents In Motorhome Be Converted To Powered VentsIn order to convert your manual operated vents in your motorhome, and the brackets and hardware that would allow you to convert their vents is very limited. We do not currently carry those parts in stock so I would need the make and model of your vents to try and locate parts that would work. You may be better off replacing a vent with a vent that has a motor already included like part # V2094SP-30. This is a 14-1/2 x 14-1/2 inch fan with a 12 V motor and white lid. The on/off switch...
view full answer... - Vent Options for a Trail Lite Camper TrailerFor a basic 12V powered vent you can use something like the Ventline # V2094SP-30 which has a manual lift and is more on the simple end of things. For something that is a bit more high-end we have the MaxxFan # MA00-07500K which has a powered lift, thermostat, and a cover on it so that you can keep the vent opened up even when it's raining outside. No matter which vent you end up going with don't forget you also need some hardware and sealant which you can find in the kit # 344270KITW. We...
view full answer... - Can You Replace The Plastic Dome On A Ventline Fan With A Metal Dome.I have a solution for you. You can use the Metal Low Profile Replacement Cover # BV0534-00 to replace the plastic dome on the Ventline Ventadome Trailer Roof Vent w/ 12V Fan - Manual Lift - 14-1/4" x 14-1/4" - White # V2094SP-30. They are compatible and will work just fine.
view full answer... - Which Trailer Vent Covers Let More Light Pass Through, White or SmokeThe smoke and white covers that are on the Ventline roof vents are both going to let quite a bit of light into the trailer. However, due to the translucent nature of the smoke covers they would let more light in. Both would last about the same amount of time. One has not been shown to stand up to the sun better than the other. For a smoke version of the part # V2094SP-30 that you referenced you would want the part # V2092SP-29.
view full answer... - Does the Fan of the Ventline Ventadome Trailer Roof Vent Pull Air Out of a TrailerThe Ventline Ventadome Trailer Roof Vent # V2094SP-30 that you referenced is an exhaust fan, what that means is that it pulls air out of the the trailer. The reason for this is that hot air rises, so when you pull out the air at the top of the trailer you will be removing the warmest air and replacing it with cooler air. I am not sure if this would be sufficient to keep your candy from melting while they are being transported through a hot desert climate. You might have to pack them in...
view full answer... - Installation Instructions for Ventline Ventadome Trailer Roof Vent with 12V Fan # V2094SP-30The part number that was provided is actually for the screen, # BVD0434-31, which is included with some Ventline roof vents. To obtain the part number for the fan you will need to remove the screen. I have attached a set of installation instructions which cover the Ventline Ventadome Trailer Roof Vent w/ 12V Fan, # V2094SP-30, as well as a few other models. If your model is not listed on the instruction sheet, please feel free to send me an email with your model number and I will get the...
view full answer...
- Solution for Needing Replacement Screen for Northern Breeze Roof VentI do have an option for you but the correct replacement screen is not available as it has been discontinued by the manufacturer. The only option we can offer you is a new unit, the Ventline Ventadome Trailer Roof Vent part # V2092SP-28 or part # V2094SP-30 with fan. These units will however be a direct replacement for the Northern Breeze Vent you have now.
view full answer... - Replacement Vent Cover for Ventline Roof VentWe have several selection for replacement vent cover for Ventline Old-Style Rounded Dome in smoke, # BV0554-03. Or in white # BV0554-01. In wedge shape, white, # BVD0449-A01. In wedge shape, smoke, # BVE0108-03. Rounded dome, white, # BBC0530-01. Rounded dome, blue/grey, # BBC-0530-04. Please note the links to product review videos and installations.
view full answer... - Can the Powered Lift Ventline Ventadome Roof Vent w/ 12V V2119-601-00 Fan Be Opened Manually?No, the lifting mechanism on the powered item # V2119-601-00 is different then the manual item # V2094SP-30. You can't just add the knob and twist it open in the event of a power failure.
view full answer... - Replacement Roof Vent Recommendation for Northern Breeze on a 2006 Jayco Jay Flight Travel TrailerTo replace the Northern Breeze V2425 vent on your 2006 Jayco I recommend the Ventline Ventadome # V2094SP-30 which is a standard manual 12V vent with a white lid - this should be pretty identical to what you currently have. Be sure to pick up the Installation Kit # 344270KITW so you get all of the hardware and sealer needed to complete the installation.
view full answer... - Will The Ventline Trailer Power Roof Vent # V2094SP-30 Fit On 1991 Fleetwood Bounder MotorhomeThe Ventline Ventadome Trailer Roof Vent w/ 12V Fan, part # V2094SP-30, is the same size as the vent you are replacing which is 14-1/4 inches x 14-1/4 inches. It is a power vent so it can be wired like your existing power vent. It will work in your 1991 Fleetwood Bounder motorhome as long as you will not be using it above a bathroom tub or shower. The Ventline power vent is not approved to be used above a tub or shower because the electrical motor is not tested to hold up to the moisture...
view full answer... - Recommended Powered RV Vent For A 2013 Heartland Trail Runner With A 7-1/2 Thick RoofTechnically you could use the Ventline Ventadome Trailer Roof Vent w/ 12V Fan # V2094SP-30 or the # V2094SP-28 but the garnish wouldn't be long enough to accommodate the depth of your ceiling. The largest garnish we carry for Ventline fans is # VA0445-37 at 5-5/16" so you'd have a gap between the vent and the garnish. You'd honestly be better off with the MaxxFan Mini Plus Manual RV Roof Vent w/ 12V Fan - LED Light - Black # MA00-03851 or # MA00-03801 for white cover. These two vents...
view full answer... - Can Ventline Ventadome Trailer Roof Vent V2094 be Converted to the Wall Mount Switch Version V2119Since the big difference between the Ventline Ventadome Trailer Roof Vent # V2094SP-30 and the vent # V2119-1-533 is that one has the control right on the unit and the other has a wall mount I see no reason why you can't just unhook the wiring from your current trim and then either route it to the Switch # VC0533-03-A. You can even swap out your current frame/screen with part # BVC0573-31 for Birch White or part # BVC0573-41 for Polar White. I have attached a video showing how to replace...
view full answer... - How is Motor Mounted to Ventline Ventadome Trailer Vent V2094You are correct, the Replacement 12V DC Motor # BVD0218-00 is mounted via screws which are underneath the fan blade (see accompanying photo), which is Replacement Fan Blade # BVD0215-00 for the Ventline Ventadome Trailer Roof Vent # V2094SP-30 (you will need this fan as well if you are replacing the motor on a fan which was manufactured before 2002. In regards to the spade connectors, you are right on the money as that is what is used with the switch. You can see that in the linked video...
view full answer...
Do you have a question about this RV Vents and Fan?
Info for this part was:
Written by:
Raymond P
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Jameson C
Expert Research:
Adam R
Expert Research:
Jeffrey L
Video Edited:
Jacob T
Updated by:
Adele M
Updated by:
Kathleen M
Updated by:
Wilson B
Updated by:
Isabelle B
Test Fit:
Randy B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Kerry
4/23/2014
It still works like its brand new. I actually bought another one this year for another location.