How to Wire the Switches of the Ultra-Fab Power Twin II Electric Stabilizer
Question:
Do you have an electrical diagram for the installation and wiring for the two motors.
asked by: Raymond A
Expert Reply:
I can tell you how to wire the motors of the Ultra-Fab Power Twin II Electric Stabilizer # UF39-941705, but the manufacturer doesn't provide a diagram, just the written instructions, which are pretty simple to follow.
You'll need to wire the switches, with the green wire going to the negative terminal of the battery, or you can ground it to the frame. The white wire from the switch will then go to the positive terminal of the battery. Then you'll connect the motors to the switches, with the black wire from the motor going to the black wire of the switch, and the red wire from the motor going to the red wire of the switch.
I have added a cut out of the instructions which goes over this, and added links below to the installation instructions as well as a video review of the Ultra-Fab Power Twin II Electric Stabilizer # UF39-941705
Product Page this Question was Asked From
Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors - 30" Lift - 6,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Pop Up Camper
- RV Motorhome
- Teardrop Camper
- Travel Trailer
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 5001 - 6000 lbs
- Electric Jack
- 30 Inch Lift
- Bolt-On
- 1 Jack
- Ultra-Fab Products
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors - 30" Lift - 6,000 lbs
- Video: Ultra-Fab Power Twin 2 Electric Stabilizer Review
- Shop: Deka Jacketed 2 Wire, 10 Gauge, Brake Wire - per Foot
- Video: Deka Wiring 10-2-1 Review
- Q&A: What Gauge Wire Is Required To Use When Installing Ultra-Fab Power Twin II Electric Stabilizer
- Shop: Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs - 30" Lift - 6,000 lbs
- Shop: Lippert High-Speed Power Stabilizer Jack - Black Waterproof Switch Kit - 30" Lift
- Q&A: Can Stabilizer Jacks for RVs Also Lift Trailers
- Video: Buyers Products Circuit Breaker with Manual Push-to-Trip Reset Review
- Shop: Buyers Products Circuit Breaker w Manual Push-to-Trip Reset - Surface Mount - 200 Amp
- Q&A: Ultra-Fab Products Trailer Jack # UF39-941705 Recommendation/Install Location on a 2007 Dutchman
- Search Results: 10 2 duplex wire
- Video: Hopkins Trailer Wiring Installation Kit Review
- Video: Deka Jacketed 10 Gauge Wire Installation
- Q&A: Maximum and Minimum Span of Wheel Masters Level Master Trailer Bubble Level Mounting Bracket
- Q&A: How to Wire Ultra-Fab Electric A-Frame Jack # UF38-944017 on 2-Horse Trailer
- Q&A: What is Difference Between Lippert Stabilizers # LC369774 and # LC298707
- Q&A: Differences Between the Lippert Components Power Stabilizer Trailer Jacks
- Shop: Ultra-Fab Power Twin II Electric Stabilizer for Trailers and RVs - 22" Lift - 6,000 lbs
- Article: My Trailer Hitch Doesn't Fit
- Shop: Brake Controller
- Article: Routing the Power Wire for a Trailer Wiring Harness
- Search Results: ultra~fab products
- Shop: Replacement Motor for Ultra-Fab Power Twin II Electric Stabilizers
- Video: Review of Lippert Components - Trailer Jack,Camper Jack - LC141893
- Video: Trailer Brake Controller Installation - 1999 Sterling L-Line
- Search Results: uf39~941705
- Search Results: trailer stabilizer
- Search Results: jack adapter
- Search Results: jack drill adapter