Summer Starts Here - Save up to 70%
Anodized aluminum electric-hydraulic actuator lets you use your brake controller (sold separately) to activate your trailer's hydraulic brakes. Includes rust-resistant marine-grade gasket and stainless steel hardware. Vented plate releases heat.
Features:
Specs:
Note: Do not power wash the Hydrastar actuator or take it through a commercial car wash. High-pressure water may damage the seals on the actuator.
The Hydrastar electric-over-hydraulic trailer brake actuator applies pressure to your trailer's hydraulic brake system in response to the electrical signals sent from your in-cab brake controller. As a result, your trailer's hydraulic brakes will be activated every time you apply the brakes in your vehicle or press the manual override on your controller. This setup is ideal for boat trailers because you will get responsive hydraulic braking, which you control conveniently from inside your vehicle with your electric brake controller.
Hydrastar Electric-Over-Hydraulic Actuator vs. Standard Surge Brake Actuators
With the Hydrastar electric-over-hydraulic actuator, you can get all the benefits of towing with an electric brake controller while using hydraulic brakes. Because this actuator will activate according to the settings you have chosen for your brake controller (sold separately), you will have more control over when and how your trailer brakes engage. Depending on the features of your brake controller, you may be able to control both the rate and intensity with which your trailer's brakes activate. You can also use the manual override on your brake controller, which allows you to engage the trailer brakes without having to apply the brakes in your vehicle. And perhaps most impressive, if you have a proportional brake controller, your brakes will be activated with an intensity that matches the braking speed and power of your rig.
This pump-and-motor-based system increases response time compared with traditional actuators because the trailer brakes are triggered when you apply the brakes in the tow vehicle, as opposed to when the trailer pushes against the hitch ball. This not only gives you faster, more efficient braking, but it also eliminates the pushing sensation that occurs in setups that use standard surge brake actuators.
Hydrastar actuators are also beneficial because, unlike standard surge couplers, they allow you to activate your brakes when reversing down an incline, such as a boat ramp. Having the ability to brake in reverse gives you more control and prevents wear on your tow vehicle.
Hydrastar Installation
This Hydrastar electric-over-hydraulic brake actuator will give you years of trailer-stopping performance. The actuator mounts on your trailer's frame with the included stainless steel hardware. Then it splices into the trailer's wiring and connects to your hydraulic brake lines from the 3/16" female port. Lines and fittings are sold separately.
Durable, Marine-Grade Construction
The Hydrastar Marine actuator is ideal for use on boat trailers. Just like other Hydrastar electric-over-hydraulic actuator models, this system is built of extruded anodized aluminum for superior corrosion resistance. The weathertight seals protect internal components from the elements. The Hydrastar Marine actuator also features marine-grade gaskets and stainless steel hardware that won't rust. These extra features make it perfect for marine applications.
This actuator also has a vented end plate that releases pressure, moisture, and heat to help prevent any internal damage. Unlike models that are unable to release heat and pressure, this vented actuator can be safely mounted inside of a compartment on your trailer. As a result, this actuator is great for gooseneck and fifth-wheel trailers where finding space on the tongue can be nearly impossible.
Brake Controller Compatibility
Not all electric trailer brake controllers will work with this electric-over-hydraulic brake actuator. See the following table to determine compatibility with common models of brake controllers. For best performance, it is recommended that you use an aftermarket electric brake controller rather than an OEM factory-installed controller.
| Manufacturer | Vehicle Years/Controller Models | Compatible | Compatible if Used with HBA-CAM | |
|---|---|---|---|---|
| Vehicles | Ford | 2005-2006 | Yes | |
| 2007-2008 | No | Yes | ||
| 2009-2015 | Yes | |||
| Dodge | 2010-2015 | Yes | ||
| GMC/Chevy | 2007-2015 | No | Yes | |
| Brake Controllers | Draw-Tite | Activator (5100) | Yes | |
| Activator II (5500 or 5510) | Yes | |||
| Activator III (5520) | Yes | |||
| Activator IV (5504) | Yes | |||
| Hayes | Energize III (81741B) | Yes | ||
| Energize III+ (HA81742B) | Yes | |||
| Energize XPC (HA81745) | Yes | |||
| Engage (HA81760) | Yes | |||
| G2 Brake Boss (81792BB) | Yes | |||
| Syncronizer (HA81725) | Yes | |||
| Endeavor (81770) | Yes | |||
| Genesis (HA81790) | Yes | |||
| Blackbird (HA81726) | Yes | |||
| Hopkins | Impulse Digital (47325) | Yes | ||
| Insight (HM47297) | Yes | |||
| Brake Force (47225) | No | |||
| Reliance (47284 or 47285) | Yes | |||
| Agility (47294 or 47295) | No | |||
| Maxbrake | Brake Controller | Yes | ||
| Redline | Redline TA900 | Yes | ||
| RedlineTA900A | No | |||
| RedlineTA1000 | No | |||
| RedlineTA1100 | No | |||
| RedlineTA1200 | No | |||
| Tekonsha | Prodigy (90185) | Yes | ||
| Prodigy P2 (90885) | Yes | |||
| Prodigy P3 (90195) | Yes | |||
| Primus IQ (TK90160) | No | |||
| PowerTrac (39523) | Yes | |||
| Voyager (39510 or 9030) | Yes | |||
| Valley | VA32812 Blackbird | Yes | ||
| VA32811 Phantom | Yes |
Average Customer Rating: 4.8 out of 5 stars (9 Customer Reviews)
Anodized aluminum electric-hydraulic actuator lets you use your brake controller (sold separately) to activate your trailer's hydraulic brakes. Includes rust-resistant marine-grade gasket and stainless steel hardware. Vented plate releases heat.
It working good on my M105A2 Military trailer. Thanks etrailer.
Well built unit that works well .
Substituted the Hydrastar unit for the surge brake actuator on my military surplus trailer. Works like a champ!
a very nice woman took my order ...she said it would ship in x business days ....i said never mind that put down the phone and run and ship my order ..she laughed and said they didn't let her into the warehouse...however if she didn't pack it up herself immediately, someone else did ..i had it way before i expected it ...hydreastar product ..1sr one lasted about ten years of almost 5 days a week use on an equipment trailer ..i expect to get same service from this one ...
Item arrived earlier than expected. Installation was easy. And now my trailer brakes work again.
Shipping box was ripped, should of had more packing material, fortunately everything was still in the box.
Easy install, works great. Installed a whole EOH system with this unit at the core. Excellent.
Do you have a question about this Brake Actuator?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.