Butt Connector - PVC - for 16-14g Wire - Qty. 1

See what our Experts say about this Deka Wiring

• How to Install an Amber Turn and Parking Light on a Trailer with Combined Brake and Turn Signals
  Many people inquire about wiring a trailer in the way you describe, and it is possible, but you will need to use a vehicle to vehicle taillight converter, part # 118158, to accomplish this. The converter will be wired inline on the trailer wiring and will break out the turn and brake circuits. I attached a drawing that shows how I would go about wiring this converter on a simple 4 wire trailer. You would just need to cap off the red wire on the output side of the converter and tie that...
  view full answer...
  
• Components Needed to Extend Length of Wiring That Powers Ventline Powered Vent Fan
  To extend the length of the wiring that powers your Ventline vent fan you can use 2 of part # DW01899-1, which is a Female Spade Terminal Quick-Disconnect, 2 butt connectors # DW05714 and a suitable length of 2-conductor wire such as # 12-2-1 (which is sold by the foot). The wiring portion of part # BVD0218-00 is not sold by itself.
  view full answer...
• Installing Brake Controller in 1998 GMC Jimmy with Cut Off 4-Way
  The kit you'll want instead of the # 37185 is the part # ETBC7L as it comes with the same 4-way to 7-way adapter but it also comes with the wiring needed to install a brake controller like the Curt # C51180. Since your 4-way was cut off you'd need to also cut the wire off of the 7-way adapter and hardwire the connections there. Since 4-ways use standard colors you'd just need to wire them color for color. For butt connectors to make these connections you'll want the # DW05714 for each...
  view full answer...
• Getting Trailer Wiring Harness 118416 to Work with a 2017 Jeep Wrangler Right-Hand Drive Model
  For some reason the right-hand drive version of the 2017 Jeep Wrangler Unlimited doesn't have the same tail light wiring as left-hand drive models. What you will have to do is plug in wiring harness # 118416 to one side or the other. On the side it is not plugged into use a circuit tester such as # PTW2993 to locate the wire that carries the turn signal and brake light function. Splice a wire into that wire on the vehicle using a quick splice connector such as # SWC501746-1 and wire # 16-1-1...
  view full answer...
• When is it Recommended To Use Dielectric Grease When Wiring
  We want to thank you for your recent purchase! You wouldn't need to use dielectric grease with a butt connector such as part # DW05714 (view video at the 1:16 mark) as electrical tape will work great. Heat shrinkable tubing such as part # DW05451 will help protect against the elements. It works with 14-18 gauge wire. Most trailer light wiring is 16-gauge. Once you have your wire inside the tubing you can use a heat gun, blow dryer and/or lighter utilize the heat shrinkable tubing. We...
  view full answer...
  
• Brake Controller Recommendation for 2021 Jeep Grand Cherokee
  I see that you'd looked at both the Redac # RED24FR Tow-Pro Liberty as well as the Tekonsha # TK90160 Primus. Either controller would work well, to answer the question of which would be the best controller for you will depend on how familiar you are with brake controllers, your budget and whether you'd be satisfied with a traditionally mounted brake controller that would bolt to the underside of the dash like the Primus or whether you'd prefer a remotely mounted controller like the Tow-Pro...
  view full answer...
• Parts Needed to Install GloLight LED Trailer Tail Light # STL178RFPB to Trailer Wiring
  Best option would be to connect the # A47PB to the wiring you have on your trailer currently so that you can easily plug in the GloLight LED Trailer Tail Light # STL178RFPB. For butt connectors you'd then want the part # DW05714. This is a really solid choice for a light and would work well for your 2018 Grand Design Solitude.
  view full answer...
• Can You Tap Into A Nearby Light To Power A MaxxAir MaxxFan Deluxe RV Roof Vent
  The MaxxFan Deluxe Roof Vent w/ 12V Fan # MA00-07500K only pulls 5 amps so you would be fine with 16 to 14 gauge wire. I've tapped into a light fixture numerous times for power but you could run into an issue if you had too many lights on that one fused line. Most likely the lights are all ran to the same fuse so if they're incandescent you could end up pulling too many amps adding in the vent and blow the fuse. If you have LED's then you'd most likely be fine since they typically pull...
  view full answer...
• Connecting New 4-Way with 4 Wires to Trailer that Has 5 Wires
  The two tan wires of your trailer wiring will get ran to the single brown wire of your new plug. This circuit is the running lights circuit and since it goes to both sides of the trailer there's two wires for it. You'd run the two wires into one side of a butt connector like part # DW05714 and the single wire from the new connector gets ran to the other side.
  view full answer...
• How To Mount the Optronics LED Clearance or Side Marker Light w/ Reflex Reflector Part # MCL31AB
  The Optronics LED Clearance or Side Marker Light w/ Reflex Reflector part # MCL31AB mounts by running two screws like part # 1131832 though the base. In order to access these screw holes you will need to remove the lens. I have attached a photo that shows the screw holes. I have also attached an install video for you as well. In order to make the wiring connections you will also need part # DW05714 and part # DW05737-1.
  view full answer...
  
• Installing Brake Controller in 2009 Chevrolet Silverado
  The Draw-Tite Activator IV # 5504 will work with a wiring harness adapter like part # 20127, for your 2009 Chevrolet Silverado. This means you will need to splice into the brake controller wiring under the driver's side dash in order to install the brake controller. There will be a bundle of wires tied together with white tape. These are the wires you will to connect your adapter to. You will want to connect the black brake controller adapter wire to the red factory brake controller wire,...
  view full answer...
  
• Which is Preferred Connection for SMI CoachLink 900 Wireless Transmitter
  The SMI CoachLink 900 Wireless Transmitter and Receiver Braking Indicator Set # SM99945 that you mentioned comes with a couple butt end connectors and a couple quick splices for tapping into a circuit. I personally don't care for quick splices as the few times I've tried to use them I either ended up cutting the circuit I was trying to tap into or didn't press the blade hard enough to get the circuits to contact. The best connection would be to solder it. For that we have the part # FL0803490...
  view full answer...
• How To Switch from Jenson RV Stereo JRV212T to Jensen RV Stereo JWM60A
  There is no adapter harness to convert the wiring from the Jenson JRV212T to the Jensen RV Stereo part # JWM60A. That said, this is actually pretty simple using the attached diagram. All you'll need is some wire crimpers/strippers like part # PT43ZR and butt connectors like part # DW05714. Just match wires from the old unit to the new unit by function and you're good to go.
  view full answer...
  
• Installation of Reese Brakeman Trailer Brake Controller in 2014 Dodge Ram
  The trailer brake controller custom wiring adapter that you referenced, Tekonsha part # 3023-P works with all Tekonsha controllers unless they are the hard-wire type like your Brakeman. Based on my research the Brakeman has four hard-wired leads exiting its back rather than a plug to accept the adapter. You can still use the adapter to make the truck-side connection to the under-dash port, and simply cut off the flat connector (that is intended for the rear port on a current Tekonsha controller)...
  view full answer...
• How To Install the Gustafson RV Sidewall Light Part # 277-000261
  The Gustafson RV Sidewall Light part # 277-000249 is very easy to install. The mounting plate can be installed using standard wood screws as you mentioned. If you like, you can use anchors for added support but these won't really be needed, just make sure to attach the base to a secure surface. In regards to wiring, there is one black wire for power and then one white wire for ground. These wires will need to be run to the distribution panel so the light can receive power. If you are just...
  view full answer...
• MaxFann model 4000K Will not Shut Off
  It sounds like the Circuit board has failed on your MaxxFan Plus Roof Vent part # MA00-04000K the correct replacement for that is the Replacement Printed Circuit Board for MaxxAir Manual Lift RV Roof Vents part # MA10A21276K. This is a direct replacement and will plug directly into the plugs on your current vent. You will need to reconnect your power and ground using a couple of butt connectors like Butt Connector - PVC - for 16-14g Wire part # DW05714.
  view full answer...
• Recommended Replacement Dome Lights For A Mobile Vet Clinic
  The closest option I could find is a bit smaller than your current 6" x 12" light fixture, but having installed other sizes of this light I can confirm that they make a world of difference when it comes to illuminating a room. The Opti-Brite 12V/24V LED RV Dome Light # OPT58FR is 13-1/2" L x 3-15/16" W and has an effective lumen rating of 1,500 lumens. To give you a comparison the # ILL07COB you were looking at only has an effective lumen rating of 354 lumens. They are a surface mount...
  view full answer...
• How to Wire Tekonsha Sentinel Brake Controller in 2007 Chevy Suburban
  Your 2007 Chevy Suburban will have tow package wiring under the dash and typically these wires will be red, dark blue, light blue (or orange) and white. These tow package wires should be below the steering column to the left of the brake pedal and tied together with white tape. It sounds like you have found the correct wires although the colors may have faded slightly from age. The RED wire from the Suburban connects to the BLACK wire on the controller; the DARK BLUE wire connects to...
  view full answer...
• OEM-Style Trailer Wiring Harness for 2011 Nissan Rogue SV
  We do offer a custom 4-pole trailer wiring harness for the 2011 Rogue that plugs in at the tail light assemblies, part # 118480 from Tow Ready. This product wires in to your Rogue at a different point than the OEM harness which we do not offer. I have linked an installation video showing the process in a 2011 Rogue. The Tow Ready harness does require a 12V power input to its red wire (made through the included wire and fuse holder). Normally this wiring connection is run up along the vehicle...
  view full answer...
• Recommended Brake Controller And Components For 2015 Jeep Wrangler Unlimited
  The installation of a brake controller like the Tekonsha Prodigy P2, part # 90885 on your 2015 Jeep Wrangler Unlimited should be very similar to the installation of a brake controller on a 2013 Wrangler as in the attached video. The # 90885 is our most popular brake controller because it is easy to install and operate. You will need the Universal Installation Kit for Trailer Brake Controller, part # ETBC7. Some of the other items used for the installation are the no-drill bracket, part...
  view full answer...
• How To Wire In The MaxxFan Mini Plus Manual RV Roof Vent w/ 12V Fan
  The two MaxxFan Mini Plus Manual RV Roof Vent w/ 12V Fan # MA00-03851 you bought will have black and white wires hidden above the fan that you'll connect to the 12v wiring of the trailer. The black wire is your power and the white wire is your ground/neutral. To connect it to the trailer's wiring you'll need to use some butt connectors # DW05714 or wire nuts to splice the wiring together. If there isn't 12v wiring in the locations near the vents then you'll need to run some 14 gauge wire...
  view full answer...
• Installation of Midship Marker and Turn Signal Light on 1996 Holiday Rambler Endeavor
  Good news! I can help you wire up a mid-ship turn signal your 96 Holiday Rambler Endeavor, but the Optronics light # MCL32AB you asked about will not blink while you have the running lights on. What you will need is the Amber LED Mid-Ship light with flange # STL75AMFB. I recommend using butt connectors # DW05714 and 16 gauge wire # 16-1-1 to make the connection to the diode from the original circuits. I have linked all the above mentioned products to this page for your purchasing convenience.
  view full answer...
• How to Access Reverse Light Signal on 2014 Volkswagen Passat
  The only ways to obtain a reverse light signal to activate a backup camera like # HM50002 are to tap into the reverse light wire at one of the tail light assemblies, or if you happen to have a 7-way trailer connector on the vehicle, tap in to the reverse light signal wire that feeds the pin on the connector. Please refer to the linked photo of a 7-way vehicle socket. The center pin carries the reverse light signal in most typical applications. It is not difficult to tap into the reverse...
  view full answer...
  
• Replacement 15A inline fuse for Tekonsha trailer wiring harness
  The ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit # 119250KIT comes with the inline fuse that you are referring to. If you don't have it, then you can go with Spectro 14-Gauge ATO-ATC Fuse Holder # SWC9538 along with the compatible Curt 15-Amp Blade Fuse # C58450-1. For the butt connector, # DW05714 would work well; this is sold in a quantity of 1. If you want shrink wrap butt connectors, then you will need to purchase a pack of 10 #...
  view full answer...
  

Do you have a question about this Wiring?