16-14 Gauge Butt Connector - 5 Pack

See what our Experts say about this Deka Wiring

• What Parts Needed to Connect Trailer with Round 5 Pin Male Connector to a Vehicle with a Flat 4 Pole
  If your trailer has stop and turn functions on separate lights (separate amber lights for the turns) you will need a vehicle-to-vehicle taillight converter harness for your Subaru that can separate the stop and turn functions. These functions are combined on a 4-pole flat connector. If this is the case you will need to fabricate your own custom harness from several components we can supply. First you will need a trailer-side 4-pole flat connector to mate with the Subaru 4-pole. You can...
  view full answer...
  
• Adding 4-Pole Connector to Existing Trailer Wiring
  A wire's color is not a reliable way to know the function it carries so to hook up an additional 4-pole to your existing towing setup you'll just want a circuit tester to allow you to confirm what each wire does. I recommend kit # 18252 which includes both a probe tester and a 6-foot vehicle-side 4-pole that will connect to the mating trailer-side 4-pole connector. You'll apply the tester to the various wires while a lighting function is activated and after you go through the functions...
  view full answer...
• Trailer Brake Controller Installation in 2008 Chevy Silverado with Factory 7-Way
  To install the Tekonsha PowerTrac Electronic Brake Controller - 1 to 2 Axles - Time Delayed # 39523 will use the wiring harness # 20127 to splice into wires under your dash that have already been run. I've attached a simple video to assist with this installation which you will be able to do. I've also attached an article with pictures to help. You will simply use butt connectors # 05731-5.
  view full answer...
• How to Rewire an Old Cattle Trailer
  It sounds like you are on the right track to rewire your cattle trailer. You are correct about the wire colors on the 7-way connector that you purchased. The colors that you see on the 7-way connector are typical for RV style trailers rather than utility, cargo, or livestock style trailers. The black wire should be connected to the terminal in the 7-way connector labeled black. This is the terminal in the 11 oclock position when you are looking at the back of the trailer connector (see...
  view full answer...
  
• Recommended Wiring for Clearance Lights on Homemade 16 Foot Car Hauler Trailer
  Depending on the size of your trailer there are some requirements for lighting. I've attached an article to assist. When wiring a trailer, I do like the option of including a junction box. I personally really like the Epicord 7-Way Molded Trailer Plug with Junction Box - 10' Long # 277-000141. This will allow you to use ring terminals # 44-5310A to make your connections. For clearance lights, you want to splice into the running light circuit (normally the brown wire) on your trailer....
  view full answer...
• Is Junction Box Recommended When Installing New Trailer Wiring 7-Way
  Using a junction box makes installing new 7-way wiring much easier. Often times, people will run the wires from a 7-way such as yours to a junction box like part # 38656. From there, they will run the standard wire colors to the trailer lights, brakes and battery. I have attached a photo that shows how this setup works in the junction box. Most molded 7-way pigtails will come wired with the RV style color code. If you ever need to replace your 7-way connector in the future, you could simply...
  view full answer...
  
• Is a Brake Controller Wiring Adapter Needed For Install on a 2011 Dodge Ram 1500 with Tow Package
  Yes, you will need the Universal Brake Control Wiring Adapter, Dodge Ram, item # 3021-S, to install the Hopkins Agility Electric Brake Controller, in your 2011 Dodge Ram 1500 Pickup. Hopkins does not offer an adapter for the 2011 Dodge Ram yet, so you will need to eliminate the connector at the back of the Agility and attach the # 3021-S adapter to the like colored wires using two 12-10 Gauge Butt Connectors, item # 05732-2, and two 16-14 Gauge Butt Connectors, item # 05731-5, 5 pack....
  view full answer...
  
• What is Needed to Wire Replacement LED Trailer Lights for Separate Turn and Stop Light Functions
  A standard 4-pole flat trailer connector carries brake light and turn signals on the same wires. Typically the yellow wire carries both left turn and stop light signals and the green wire carries both right turn and stop light signals. The brown wire carries the running light signal for both sides of the trailer and the white wire is the ground. Please refer to the photo attached. In order to separate the turn and brake signals so they can be sent to separate lights you will need a vehicle-to-vehicle...
  view full answer...
  
• Is There a Trailer Side 4-Round to 4-Flat Adapter
  So I know the wiring harness you're describing, the 4-round, and there isn't an adapter to get it to go to a 4-flat. That's okay though because there is a really simple solution. What you can do is just cut off your round 4-way and add a standard, trailer side 4-flat, part # W787264. All you'd need to do is connect the wires with butt connectors # 05731-5. I've added links below to a couple help articles for you to check out as well on wiring which may be useful.
  view full answer...
• LED Red Marker Lights That are Made in the USA
  We do have some red LED clearance lights that are made in the USA. They are made by Command Electronics, and I was able to confirm with the manufacturer that the following lights are in fact made in the USA: - LED Trailer Clearance or Side Marker Light with Reflex Reflector - 2 Diodes - Red Lens # 328-K-59LB - Hot Dot LED Trailer Clearance and Side Marker Light - 2 Diodes - Red Lens # 328-003-17R Both of these lights are surface mounted and have 2-wire leads, with the red wire being...
  view full answer...
• Recommended 12 Volt Vent With Wall Mounted Control Switch
  We do have exactly what you need for a roof vent for your camper, so long as it has the standard 14" x 14" square cut out. What you'll need is a 12 volt vent from Ventline, which comes included with a dog-proof wall mounted control switch (ok it isn't technically dog-proof but will certainly never be confused for a chew toy). You have an option for either White or Smoke in color: - White: Ventline Ventadome Roof Vent with 12V Fan and Wall Switch # V2119-1-533 - Smoke: Ventline Ventadome...
  view full answer...
• How to Install 3-Wire Optronics Oval LED Trailer Turn Signal and Parking Light STL78AB
  The Optronics Oval LED Trailer Turn Signal and Parking Light # STL78AB uses a separate white ground wire along with the two power input wires, black for parking and red for turn. Odds are your original incandescent lights used their mounting hardware to establish the ground so you'll want to find a suitable bare metal surface to make that connection using a ring terminal like # DW05737-1 (order two). You will also want to apply dielectric grease like # 11755 to that grounding point to...
  view full answer...
• How to Connect Trailer wiring for 2013 BMW X3
  Your 2013 BMW X3 has a Pulse Width Modulation Stop/Tail (PWM ST) wiring systems, sometimes called Multiplex wiring. The Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector # C59236 will work with your X3, but it has to be installed a certain way for all the lights to function properly. Since you already have done some testing and identified what kind of system you have it will be easier and quicker to get installed. You need to test and identify the color of wires for...
  view full answer...
  
• Parts Needed to Totally Rewire Trailer
  The Trailer Wiring 7-Way Kit # HS381-9000 is a good place to start. It gives you a new 7-way and wiring to a junction box where you can then wire all of the circuits to. Additional hardware that you may need is 3/16 Inch Ring Terminals, # 44-5310A, 1/4 Inch Ring Terminals, # DW05702-1, 12-10 Gauge Butt Connectors, # 05732-2, 16-14 Gauge Butt Connectors, # 05731-5, and electrical tape. And finally 10 gauge wire like part # 10-1-1 which is sold by the foot and 12 gauge wire # 12-1-1. The...
  view full answer...
  
• How to Wire Wesbar 7-Function LED Wrap-Around Tail Light 271594
  Thank you for your photo. On your trailer's original lights the connector's exposed pin is the ground while on your replacement light # 271594 the ground is on the white wire as you noted. For these new lights the red wire carries stop/turn signals while the black wire carries running light signal. You can use butt connectors like # 05731-5 to make your wire splices and we recommend also applying electrical tape over those splices to protect them.
  view full answer...
  
• Easily Replace an Elite EEDV06 Entertainment Center Receiver With Furrion DV1230BL Receiver
  Yes, you can use the Furrion # DV1230BL stereo receiver to replace your Elite EEDV06 model. They are both double-DIN size, so it should fit right in the opening left by the Elite. The Furrion has many of the same features and some updated features as well. Also, I feel the Furrion brand is superior in quality and customer service. There is not a radio with an exact match for the wiring harness that came on the Elite, however, changing the wiring is a simple process. All the connections...
  view full answer...
  
• Butt Connector Recommendation for Use with Trailer Wiring Light Kit # TL16RK
  The Deka 16-14 Gauge Butt Connectors - 5 Pack, # 05731-5 would be a great choice to allow you to wire up all of the lights you mentioned. The brown wire of the # TL16RK is a single wire that you'd need to run from one side of the trailer to the other.
  view full answer...
• Will a Hopkins Brake Control Wiring Harness Work with a Tekonsha 2030 Mark 12 Brake Controller
  Yes, the Hopkins wiring harness 47775 will work with the Tekonsha 2030 Mark 12 brake controller. The brake controller has bare wires and the harness only has a connector on one side. All you have to do is splice the wires with butt connectors, # 05731-5. The white wire is ground Black is 12 volt power in Red is input from the brake switch Blue is output to the trailer brakes On a 2003 Chevy Silverado there may be additional connections to make under the hood to make everything fully...
  view full answer...
• Installation of Tekonsha Prodigy 3 Brake Controller # 90195 in 2003 Ford Explorer
  The # 3035-P Brake Controller Wiring Harness is right at 32 inches long. The best place to mount the controller is to the right of the steering column within easy reach of the driver. If you click the provided link, and fast forward the video to the 4:00 mark, you can see our installer running the connector behind the center console using a pull wire. If you should find that the harness isn't long enough, you can always graft in some lengths of 16 gauge wire for the stoplight switch and...
  view full answer...
• Wiring Connections for Installing Tekonsha Primus IQ Brake Controller on 2018 Chevy Traverse
  On your Tekonsha Primus IQ Trailer Brake Controller # TK90160, the blue wire is for brake output, the red wire is for the brake light switch on the vehicle, the black wire is for 12V power, and the white wire is for ground. Based on the functions you found listed for the factory wiring on your 2018 Chevy Traverse Limited, the following connections will be made when installing this brake controller: Blue wire on Traverse to Blue wire on brake controller Red/Black or Red/Blue wire on Traverse...
  view full answer...
• Wiring Harness for Curt Spectrum Trailer Brake Controller on 2016 Jeep Wrangler Unlimited
  The correct adapter for the Curt Spectrum # C51170 trailer brake controller on your 2016 Jeep Wrangler Unlimited is Wiring Adapter for Curt Trailer Brake Controllers # C51515. One end of this adapter will plug into your Spectrum brake controller and the other end will splice into your Jeep's brake controller wiring; you can use Butt Connectors # 05731-5 to help make this connection. I have added a link to a video review of Adapter # C51515 for you to check out as well.
  view full answer...
• Clearance Lights and Tail Lights Not Working on 5th Wheel
  It sounds as if you've blown a fuse. Check fuse in location F29 in the fuse panel in the engine compartment, and replace as needed. Before plugging the trailer back in, you'll want to locate the short in the running lamp circuit on the trailer that caused the fuse to blow. Take a good look at the running lamp circuit to find the short, and repair it otherwise, you'll continue to blow fuses. To repair the short, you can use # 16-1-1 to graft in a new piece of wire as needed the wire is...
  view full answer...
• Can I Install a Third Brake Camper Taillight to My 7-Way Wiring Harness?
  I went ahead an brought this to my attention to my fellow experts, and while you cannot wire your third brake light directly into your 7-way wiring harness like the # ETBC7 on your 2000 Toyota Tacoma, you can wire it directly to the brake light wiring you currently have installed. In order to determine what wire you need to splice into, you I recommend using a circuit tester like the # PTW2993 to find the correct ones. Also, you most likely need more 16-gaguge wiring # 16-1-1 and heat-shrink...
  view full answer...
• Installation of Optronics Sealed, 6-1/2 Inch Oval LED Trailer Stop, Turn, and Tail Light
  Thank you for your purchase from etrailer.com! The Optronics Sealed, 6-1/2 Inch Oval LED Trailer Stop, Turn, and Taillight # STL78RB that you purchased will need to be hardwire installed on your trailer. You will want to connect the light to your trailer's wiring by function. You can use a circuit tester, like # PTW2993, to determine the functions of your trailer wiring. The white wire on the light will need to be grounded. I recommend running the light ground back to the main trailer...
  view full answer...
  

Do you have a question about this Wiring?