You will need the Firestone Ride-Rite Air Helper Springs # F2558 for your 2016 Nissan Frontier. You will not need any spacers as the Rough Country 2.5" leveling kit only provides lift to the front suspension.
The Air Lift WirelessAIR Compressor System # AL58WQ will allow you to control the air pressure with your smart phone and the Air Lift app. The smart manifold will monitor the air pressure while you drive and make adjustments to the air pressure if it changes by more than 3psi. It... view full answer...
WeatherTech currently only carries a tailgate liner for a 2022 Nissan Frontier with a 6' bed so the only other option I currently have is the Access Custom Truck Bed Mat # A45BG. This half inch thick carpet easily snaps in and out of place so that you can protect your bed or pull the mat out to clean it.
WeatherTech does carry a tailgate liner # WT42XQ if you're looking for tailgate protection as well. view full answer...
The pilot diameter of the trailer wheel part # AM22627 is 3.19 inch so you'd need a center cap like part # 319EZ. For locking lug nuts you'd want part # RG01-150 or for standard lugs # LHLR103. view full answer...
I have a possible solution for you, but none of the tailgate-lowering systems with shock absorbers will work with your 2018 Nissan Frontier. You may be able to use the Hopkins EasyLift Truck Bed Tailgate Lift Assist # 74211, but this also has not been confirmed to fit your vehicle so I cannot say for sure if this will work. It uses a single torsion bar to make lifting and lowering the tailgate easier. I recommend looking at the demonstration video I attached along with the photos on the... view full answer...
As long as you have room for the # PK-28WL2-BM you won't have a problem mounting it on your 2017 Nissan NV 3500. The rack has a tower height of 46-3/4". Considering the fact that someone mounted this on their NV 2500 I don't think you will have an issue, see the attached picture below. view full answer...
When we installed the Draw-Tite # 76031 and Curt # C13309 trailer hitch receivers on a 2018 Nissan Pathfinder - which is the same body as a 2019 Pathfinder - we found that the Draw-Tite had both better ground clearance and better bumper clearance.
The Curt measured 14 inches from the ground to the top of the hitch with 5 inches from the hitch pin hole to the end of the bumper, while the Draw-Tite measured 14-1/2 inches from the ground and 4 inches from pin hole to the end of the bumper.
Due... view full answer...
The Draw Tite hitch part # DT23MR that you referenced is a confirmed fit for your 2021 Nissan Rogue and also is compatible with the hands free liftgate you have as well. Basically you'd just have to kick to either side of the hitch opening and you'd be set. view full answer...
If you have two vents, you are correct that you would need to order two of the Valterra Bug Screens for Dometic RV Refrigerator Vents # A10-1311VP. view full answer...
The Westin HDX Grille Guard with Punch Plate # 57-3915 will interfere with the front sensors and camera on your 2016 Nissan Titan XD Pro 4X. This is true for all of the available grille guards. If you do decide to buy it and install it I recommend checking with your local Nissan dealer to see if it is possible to relocate them. Sometimes they make relocation kits, at least for the sensors. view full answer...
It sure will!
The # HM43534 is a replacement for the factory provided 7-way. If your truck is a US market vehicle that didn't come with the factory 7-way, you'll need to use # 118266 which includes the necessary relays to activate the tow package. If you have a Canadian market truck, use # 118281
Assuming your trailer has an electric lockout on the surge coupler that prevents the brakes from actuating when the truck is placed in reverse, any of the options mentioned above would work for... view full answer...
I may have a solution for you, but the Rhino Rack # RRRBC050 does not have a way to carry tires wider than 2.7". If you' need a roof top carrier for a wider tire bike then I recommend using the Yakima Highroad # Y02114 since it can handle tires up to 4" wide. Roof top bike carriers are typically designed for smaller sized bike tires, but the Highroad does allow for carrying some wider size tires.
I've linked a short review video we did of this carrier for you to check out. view full answer...
The Draw-Tite # 75902 fits 2008-2020 Rogue models, and although it isn't a fit for your 2021 model, we do have a hitch fit available for the 2021. I'd recommend the Curt Class III, part # C24HR.
If you'll be using the hitch for towing, you'll also need a trailer wiring harness, part # TK76FR, a ball mount like
# 2753 and # 19260 for a 1-7/8 or # 63845 for a 2 inch hitch ball. view full answer...
You can use the Rhino-Rack Universal Load Assist # RR-RUSL with most crossbars including your factory bars on your 2017 Nissan Rogue. They just wrap around your crossbars to mount into position. I've included a video for you to watch to see the installation process! view full answer...
The Yakima SkyBox NX 16 Roof Cargo Box # Y95AV will fit your 2018 Nissan Armada's factory crossbars if the crossbars measure less than 3-1/2 inches wide and less than 1-11/16 inches tall. For a definite confirmation of the fit, I recommend measuring the crossbars. As far as the rear hatch compatibility, the Yakima SkyBox NX 16 will allow you to fully open the rear hatch on your Armada. view full answer...
The Thule Insta-Gater Pro Truck Bed Bike Rack # TH93VR that you referenced was designed to be able to secure bikes by the front or rear wheel. It will work great with your Trek Verve 2 and would not interfere with the derailleaur. view full answer...
I don't see any reason why the Yakima OverHaul HD wouldn't fit your 2022 Nissan Frontier. This is a pretty universal application so I imagine Yakima is just waiting to officially say that it fits once they can actually get it tested. I say go for it. If you have the standard bed then you need part # Y01151-57 but if you have the tracks in your bed then you need the part # Y01151-5768.
Attached is a review video for you to check out. view full answer...
I have a solution for you to tow your 2019 Nissan Sentra NISMO, but I spoke with my contacts at both Roadmaster and Blue Ox and neither one offers a base plate for the 2019 Nissan Sentra NISMO. They gave me 2 reasons for this, but their primary reasoning was the turbo on the NISMO trim package gets in the way and keeps base plates from being mounted on the front of the vehicle; the secondary reason is the front grill/trim doesn't provide good mounting spots.
The best option for towing... view full answer...
The TruXedo Elevate Truck Bed Rack System # TX46NV is an excellent choice and will fit perfectly with the BAK Revolver X4s # BAK34AV on your 2022 Nissan Frontier with the 6' bed (no Utili-Track System). I really like the Elevate system because it not only is compatible with some tonneau covers but it also has T-Slot channels where the crossbars can adjust back and forth and other accessories can be mounted as well. view full answer...
After looking at the owner's manual for your 2022 Nissan Pathfinder, nothing says you cannot use sway control with the vehicle sway control system. There is a "Sway control device" section which only says make sure the device will work with the vehicle, hitch, trailer and the trailer's brake system.
If you choose to use a WDH like the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control # EQ37060ET you could shut off the vehicle sway control system to ensure there is no conflict... view full answer...
To add a 7-way to your 2011 Nissan Pathfinder, all you need to do is add the Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 7-Way Trailer Connector # C56226.
This will replace your 4-way and give you the 7-way you need to tow your camper with electric brakes. You'll then be able to use a brake controller like the Curt TriFlex NEXT # C24VV with Wiring Adapter # C51382. view full answer...