Expert Answers about Nissan Frontier
- How to Install the Hopkins HM43534 7 Way Adapter On a 2014 Nissan Frontier
- The Hopkins Plug-In Simple Vehicle Wiring Harness for Factory Tow Package - 7-Way and 4-Flat Connectors # HM43534 is actually a plug and play option for your 2014 Nissan Frontier. Though this will come with a bracket to attach it to the bottom of the bumper or in some other way, you may be able to mount it in the hole you already have in said bumper.
The holes will measure 2-1/2 inches from center to center when going across horizontally, so if this matches the mounting holes you already...
view full answer... - Removing The Tailgate With The Pop & Lock Tailgate Lock # PAL8450 Installed
- The Pop & Lock Custom Tailgate Lock - Power - Black # PAL8450 has a short wiring harness that will run through the tailgate and then under the bed to the frame and plug into the long wiring harness connector so as long as you mount the connectors is an easily accessible position under the vehicle it should only take a few seconds to unhook them and then remove the tailgate.
view full answer... - Can A Grille Guard And Front Hitch Both Fit A 2011 Nissan Frontier
- The mounting locations for both a grille guard and the Draw-Tite Front Mount Trailer Hitch Receiver # 65075 front mount hitches are usually some of or the same installation points and/or occupy some of the same space in the front of your Nissan Frontier. You always have the option to remove the grille guard first and then install the front hitch to use either or but it's highly unlikely you'll be able to use both at the same time.
Included are the instructions for this front mount hitch...
view full answer... - Does Hopkins 7-way and 4-way Connector HM43534 Fit 2019 Nissan Frontier W/ Factory 7-way Connector?
- The Hopkins Plug-In Simple Vehicle Wiring Harness for Factory Tow Package - 7-Way and 4-Flat Connectors # HM43534 you were looking at for your 2019 Nissan Frontier SV is an exact replacement for the factory 7-way you have installed, and will give you both a 7-way and 4-way connector.
view full answer... - Trailer Wiring Fit For 2022 Nissan Frontier
- So you will need to access the 12 pin jumper plug in your Frontier's cab, which as you said is on the passenger’s side behind the kick panel. This is where you will install the harness and relays that activate the trailer tow package, and the correct harness for your 2022 Nissan Frontier, that does have those relays, is from Curt:
- Curt Wiring Harness with 4-Pole Flat Trailer Connector # C56225
Then, to finish the install of the # C56225, underneath your Frontier there are two places...
view full answer... - Can a 4-Way Trailer Wiring Harness be Installed on a 2013 Nissan Frontier with Factory 7-Way
- All you will need to use a 4-Way and keep the 7-Way also is a simple adapter like # PK12716. You will not have to worry about hardwiring in anything or losing out on the use of the 7-Way.
If you were to install a replacement factory 4-Way you would not need any additional relays. The ones that work with the 7-Way also work with the 4-Way. If you choose to install a 4-Way you will have to disconnect the 7-Way because they plug into the same locations.
view full answer... - 7-Way Trailer Connector Compatible With Trailer Surge Coupler for 2015 Nissan Frontier
- It sure will!
The # HM43534 is a replacement for the factory provided 7-way. If your truck is a US market vehicle that didn't come with the factory 7-way, you'll need to use # 118266 which includes the necessary relays to activate the tow package. If you have a Canadian market truck, use # 118281
Assuming your trailer has an electric lockout on the surge coupler that prevents the brakes from actuating when the truck is placed in reverse, any of the options mentioned above would work for...
view full answer... - Which Bull Bars Work with Replacement Brackets and Hardware # 32-169PK
- Replacement mounting brackets and hardware # 32-169PK fits Westin Ultimate Bull Bar # 32-1695. They are designed to fit the following vehicles:
2005 - 2017 Nissan Frontier
2005 - 2007 Nissan Pathfinder
2005 - 2015 Nissan Xterra
view full answer... - Tire Chains for Size 265/75R16 Tires on 2011 Nissan Frontier Pro4X 4WD
- Some vehicles can use tire chains only on certain specific tire sizes; others can use them only on one or the other axle. The online owner's manual for the 2011 Nissan Frontier indicates on page 8-39 that you can use our low-profile S-Class type chains on the REAR wheels only so long as you are using one of the stock tire sizes that are offered from the factory. Your 265/75R16 tires are one of the stock sizes.
We have two options in S-Class chains to fit your rear tires. Both are cable...
view full answer... - Hitch Ball for Equal-i-zer Weight Distribution System
- Equal-i-zer weight distribution system # EQ37040ET, which is the same as the product you referenced does not require a 2-5/16" hitch ball; I took a look at the Equal-i-zer site and could not find a reference to that. However, if you need a 2-5/16" ball then the right one would be the 2-5/16" Hitch Ball for Equal-i-zer Weight Distribution Systems # EQ91-00-6100. It is also recommended you use Thin Walled Socket for Equal-i-zer Hitches # EQ70-00-4800 to make installation of this ball a little...
view full answer... - Does Base Plate Fit 2021 Nissan Frontier With Automatic Transmission
- It does; the "Manual Transmission" spec on the page is due to the fact that only the manual transmission for your 2021 Nissan Frontier can be flat towed, unless you get a drive shaft disconnect like you are. But the transmission does not affect the fit of the base plates, so they will work on your '21 Frontier. Along with the base plates there are a number of other parts you'll need, which I'll go ahead and list out for you:
- Base Plate Kit: Roadmaster Direct-Connect Base Plate Kit #...
view full answer... - 7-Way For 2021 Nissan Frontier Without Factory Tow Package
- We do have an option for you as the Hopkins # HM43534 is only for the factory tow package. So because your 2021 Nissan Frontier does not have the factory tow package, you'll need a wiring kit that includes the relay jumper harness which connects to a 12-pin plug that is behind the kick panel on the passenger’s side in the cab. The correct part to add a 7-way is the following:
- Curt T-Connector Vehicle Wiring Harness # C56226
The relays and jumper harness of the # C56226 are not available...
view full answer... - Will the Trifecta ALX # EX73CV Work with Utili-Tracks on a 2018 Nissan Frontier?
- Yes! I confirmed with my contact at Extang that the Extang Trifecta ALX Soft Tonneau Bed Cover - Folding # EX73CV comes with brackets that are compatible with Utili-Tracks on a 2018 Nissan Frontier (6-foot bed without bed extender).
If you need protectant spray for a little extra shine, I recommend the Extang Tonno Tonic Protectant Spray for Vinyl Tonneau Covers # EX1181.
view full answer... - Will the Pro Series Complete Weight Distribution System Work with a 2 Inch x 3 Inch Trailer Frame
- You will have no problem installing the snap-up brackets from the Pro Series Complete Weight Distribution System, # PS49901, on your 2 inch wide x 3 inch tall trailer frame, but the sway control ball plate may be a close fit.
The plate that bolts to the trailer frame for the sway control bar measures 3 inches x 6 inches. This means the ball plate is the same height as your trailer frame. I spoke with my contact for Pro Series and he said this bar should work on a trailer frame that is...
view full answer... - Will The Universal Mounting Panel For Redarc Brake Controllers Fit A Blank In A 2023 Nissan Frontier
- The Universal Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob # 331-TPSI-001 is going to require a 1" diameter hole in order for it to fit in your blank panel spot. The face of the panel is approximately 1-1/16" wide x 1-1/2" tall.
view full answer... - Best BAK Tonneau Cover and TracRac Ladder Rack Combination on 2016 Nissan Frontier
- The TracRac SR # TH43001XT-600 you mentioned will not fit the 5 foot bed 2016 Nissan Frontier, it's for the 6 foot bed. For the 5 foot bed you'll need # TH43001XT-603EX.
The TracRac SR is not likely a fit with the BAKFlip F1 BAK72506 for a couple of reasons. For one when opening the panels of the BAKFlip you will most likely come into contact with the uprights of the TracRac. It's possible you could slide the ladder rack to avoid this. Another problem is that the tracks of the TracRac...
view full answer... - Fitment of Older Yakima and Thule Systems on a 2014 Nissan Frontier and 2015 Ford C-Max
- Thank you for all of the info and the pictures! When I looked at everything it sadly looks like none of your current older equipment will fit your newer vehicles save for the Thule bars on the C-Max.
For your 2014 Nissan Frontier you can either use a 1 or 2 bar roof rack with a load extender or a ladder rack (or by itself) if you want. Here is a list of the following:
2-bar roof rack:
54" Vortex Crossbars - # RRVA137B-2
2500 Series Legs - # RRRLKVA
Fit Kit - # DK374
1-bar roof rack:
54"...
view full answer... - Will the BedRug Truck Bed Liner fit a 2012 Nissan Frontier with a Utili-Track and Spray In Bedliner
- Yes, I spoke with my contact at BedRug and she informed me that this BedRug Custom Truck Bed Liner # BRN05CCK will work on your 2012 Nissan Frontier with a spray-in bed liner and Utili-Track tie down system.
Check out the installation instructions I attached for this product also.
view full answer... - Are There Spacers for SumoSprings On Lifted 2020 Nissan Frontier
- The SumoSprings Solo Custom Helper Springs part # SSR-612-40 for a 2020 Nissan Frontier don't come with spacer nor are their any designed for this as the springs are made for factory suspension. If you wanted to make your own I don't see any issue with this just keep in mind you'd also need longer bolts. A better option would be the Timbren Rear Suspension Enhancement System part # TTORTUN4L as they do offer spacers for them, part # A25723-90AH00 and part # TA25722-90P00.
The Timbrens...
view full answer... - Is There A Front Mounted Hitch Receiver For The 2004 Nissan Frontier.
- I have a solution for you.
There is not a custom fit front mounted hitch receiver for the 2004 Nissan Frontier. However, you can use the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver - Weld On - Class V - 2" # 41990-07 it will take some fabrication though. It is possible and is done frequently. I'll attach a picture of it for an example.
view full answer...
Go To Results