How Many Valterra Bug Screens for Two Dometic RV Refrigerator Vents

Question

Question:

I just purchased a travel trailer and need to add these bug screens on the vents. It’s a Dometic and has both an upper and lower vent. The upper may be associated with the microwave since it sits directly above the fridge in the camper. I am assuming I would need to order 2 sets of these vent screens?

asked by: Randall

1

Helpful Expert Reply:

If you have two vents, you are correct that you would need to order two of the Valterra Bug Screens for Dometic RV Refrigerator Vents # A10-1311VP.

expert reply by: Kyle S

1

click to enlarge

Answer 1

I personally measured several of the openings in the Valterra Bug Screens for Dometic RV Refrigerator Vents #A10-1311VP using digital calipers. Each square is approximately 0.1 inches square. They are almost too small to use the calipers! Smaller…

view full answer...

Answer 2

The Camco RV Furnace Screen #CAM42141 is not trailer specific, but is instead designed to fit over DuoTherm and Suburban furnace vents that measure 3" in diameter, so you'll want to measure the vent opening in order to determine if…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

How Many Valterra Bug Screens for Two Dometic RV Refrigerator Vents

Product Page this Question was Asked From

Continue Researching