The hitch you referenced, Draw-Tite 2-inch Class III hitch # 75714, is a confirmed fit on the Nissan Quest for model years 2011 through 2016. But for your 2005 model year there we have a hitch that is confirmed to fit, the Curt hitch # C13563.
This hitch is made for your 2005 Quest as a custom-fit for that vehicle and offer a no-drill installation. This hitch fits for the 2004 through 2009 Quest. An install video for this Curt hitch is linked for your review. If you also need a wiring... view full answer...
The tongue weight (or hitch weight) is the maximum amount of weight that the frame of the vehicle can withstand without being damaged. You'll also always be limited to the lowest rated component in your towing setup, so even if your hitch says maximum 500-lbs tongue weight, but the vehicle is only rated for 350-lbs (which my research indicated), you will be limited to that 350-lbs. This means that any carrier and motorcycle must have a combined weight of less than 350-lbs.
When it comes... view full answer...
This WeatherTech All-Weather Front Floor Mats # WTW16GR is both the front driver and passenger side floor mats for your 2009 Nissan Quest.
I attached installation instructions for you to check out also. view full answer...
The Thule Passage 3-Bike Trunk Mounted Bike Rack, part # TH911XT would indeed be compatible with both your 2013 Prius and your 2008 Nissan Quest van. Just make sure not to use the rear windshield wiper when the rack is in place. You'll also want to remove the rack before opening the rear hatch of either vehicle. The struts that hold the rear hatch up are only rated for the weight of the door. Adding the weight of the rack (even though they don't weigh much) could result in the hatch closing... view full answer...
The hardware supplied with the Draw-Tite Hitch # 75714 for the 2012 Nissan Quest is specific to your vehicle. It may be that the threads in the weld nuts on the frame are dirty. It is not uncommon for road dirt to find its way into the threads and accumulate, making it difficult to get the bolts started.
You can try using a spray-on penetrating rust remover like WD40 and a brush such as part # DW00254 to clean out any debris from the threads, as shown in the linked installation video.... view full answer...
The High-Low adapter # RM-076 was not designed to be used for that purpose. The adapter has a tongue weight capacity of only 100 lbs, and is designed for towing a vehicle that is resting on the ground behind another vehicle.
The Curt Multi-Purpose Ball Mount, # D210 might possibly be an option. The ball mount would raise your bike rack by 4-3/4 inches. The unit is rated at 7500 lbs towing, 750 lbs tongue weight. The receiver portion has a tongue weight capacity of 350 lbs. view full answer...
The Draw-Tite hitch you were looking at, part # 75278, fits GM vans of the late 1990's and early 2000's.
Trailer hitch receivers are custom designed for specific vehicles so that they install in the best possible location. The correct hitch for your 2017 Nissan Quest is the Curt part # C13078. It bolts onto existing mouting locations on your van so there's no drilling. I've linked an install video on a 2016 Quest which is the same generation so the process is the same.
If you're going... view full answer...
There is a fit for a trailer hitch on a 2017 Nissan Quest.
I confirmed with Curt that if your '17 Quest is a Platinum, S, SL or SV model then the Curt Trailer Hitch # C12061 is a fit. view full answer...
The Curt trailer hitch # C13563 will fit a 2005 Nissan Quest. It actually fits the 2004 to 2009 Nissan Quest. I have included a link to the installation instructions for you to view.
If you plan on doing some towing, I recommend the etrailer ball mount kit, # EBMK4, which comes with a ball mount, interchangeable ball set, a hitch pin with clip, and a carrying bag.
For trailer wiring, use # 118469. I have included a link to the installation details and a link to a video showing a typical... view full answer...
Thule, the manufacturer of these bike racks, doesn't recommend the use of a 3 bike carrier on your vehicle. The Thule Speedway Trunk Mounted 2 Bike Carrier would work on your 1994 Quest. If there is a specific vehicle that you are planning on purchasing, I can check the fit on that one, if you'd like. Your other option is to use a hitch mounted 3 bike rack. The hitch would be sold separately. Just make sure you choose the correct rack for the hitch class. view full answer...
Yes, I checked with Thule and the Thule Passage Bike Rack part # TH911XT that you referenced has been confirmed to fit your 2013 Nissan Quest.
If you plan on carrying any womens or alternative framed bikes without horizontal top tubes you may also be interested in purchasing a Swagman Easy-Out Women's and Alternative Frame Bike Adapter # 64005 to provide a horizontal top tube on your bikes to provide an attachment point. I attached a review video for this product also. This will allow... view full answer...
The SportRack Vista XL cargo box, # SR7018, is designed to fit cross bars no wider than 4 inches and with a center to center distance between the bars of 25-7/8, 27-7/8, or 29-7/8 inches. You will need to measure the cross bars on your 2007 Nissan Quest to determine if they are within these measurements. I have included a link to a video review of this box for you.
For a box that is confirmed to fit the factory roof rack on your 2007 Nissan Quest you can use the Force XT, # TH6358B. view full answer...
The particular Class III Draw-Tite hitch that you referenced, part # 75714, is not rated for use with a weight distribution system. This is noted in our product specs for this hitch.
Of the three Class III hitches offered for your 2014 Nissan Quest (please see the link provided for you) only one hitch, the Curt # C13078, is rated for use with weight distribution. Its tongue weight capacity becomes 500-lbs and its towing capacity becomes 5000-lbs with a system installed.
In general a... view full answer...
I have a solution for you but the Curt Trailer Hitch Receiver item # C13078 you were looking at only has a 300 lbs tongue weight capacity. To haul your mobility scooter and carrier you will want the Draw-Tite Max-E-Loader Trailer Hitch Receiver item # 75714. This hitch has a 500 lbs tongue weight capacity. The Draw-Tite is custom fit and bolts directly to your 2017 Nissan Quest's frame with included hardware. I have linked an installation video below. You won't need a class IV hitch but... view full answer...
We have a cargo box with this kit on display in our showroom so I measured the U-bolts. The inside width of the U-Bolt in the kit is 3-1/4 inches. As long as the cross bars are no wider than 3-1/4 inches and no thicker than 2 inches, the mounting kit should fit fine.
Your box should have a metal strip in the bottom for this kit to mount properly. If not you will need the QM3 Quick On-Off Mounting Hardware Kit, TH04997, which has plates to support the bottom of the box. view full answer...
According to Curt, the # C13900 is a fit for the Nissan Frontier and the small Nissan Pickup that predated it but they don't list the Quest as a fit.
I'd recommend using the Curt # C13078 Class III hitch which is specifically designed for your 2017 Quest. If you'll be using the hitch for towing purposes, you'll also need the # C56342 trailer wiring harness, a ball mount like # 40346 (use in the rise position) and a 1-7/8 inch ball like # 19260 or a 2 inch ball like # C40004. You'd also... view full answer...
The Orion Campfire Starter Mini Flares # RN753-01 are not recommended by the manufacturer for indoor use. There is a label on the top of the box that states they are for outdoor use only. The flare can also be used for an emergency flare and has a burning time of 5 minutes.
As an alternative, I recommend using the Fire Starter Sticks # CG85FR which can be used indoors view full answer...
The trailer hitch receiver that we offer for a 2004 Nissan Quest is the Curt Trailer Hitch Receiver part # C13563. This Curt hitch will only fit years 2004 - 2009 of the Nissan Quest, nothing else. The Curt hitch, like most of our other trailer hitch receivers, is custom fit, so they only fit one model unless there is another model that shares the same chassis and even then, that is not always the case.
If you can let me know what other Nissan vehicles you have, I would be glad to offer... view full answer...
Yes, the Tow-Ready Custom Fit T-One Style Wiring Harness # 118469 is confirmed as a fit for your 2004 Nissan Quest.
This wiring harness is a T-one style and it plugs directly into the back side of your taillights on your Quest. There is no need for cutting, splicing, or wire tapping. This wiring harness includes a modulite that ensures that the vehicle wiring is compatible with the wiring of your trailer.
This wiring harness supplies a 4-way flat vehicle connection point for your towing... view full answer...
We do have front row mats for your 2006 Nissan Quest colored grey. They are WeatherTech All-Weather Front Floor Mats - Gray # WTW16GR or the Husky Liners Auto Floor Mats - Front - Gray Item # HL51142. These are both semi-custom rubber mats that are easy to clean and are molded to fit your Nissan's floorboard and stay in place. view full answer...
Go To Results