Summer Starts Here - Save up to 70%
14-1/4" Long x 1-3/16" tall. Waterproof identification light bar with 3 replaceable incandescent lights is designed for trailers wider than 80". Polycarbonate lens and stainless steel base. Surface mount. Male 0.180 bullet.
Features:
Specs:
Manufacturer Cross Reference
Light will work as an exact replacement for:
Wesbar # 003306
Peterson # M151-3RL
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The housing and lens of each light are sonically sealed together to create a single unit, which means that water will not get into the light and damage the diodes or circuit board.
A P2-rated or P3-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Ryan: Hey everybody, Ryan here at etrailer. Today, we're going to be taking a look at and showing you how to install the Optronics trailer identification light bar. So this is going to be designed for trailers over 80 inches wide and as rear clearance lights. It's going to be a perfect replacement. In our case, our customer's light today was all beat up and not working anymore. So this is really bolted right on.So one big advantage this one has over many others is that it is going to be made out of stainless steel.
That's something you really want to think about, but you're not going to have to worry about any rust or corrosion. And unlike plastic, you're not going to have to worry about it cracking. So with that being said, once you have it on here, really not a whole lot to worry about. However, if one of your bulbs does go out, you can replace them and you can find those here at etrailer. All three of the lights are going to be nice and bright.
Even with our shop lights on here inside. That way, everyone can see you. Just to give you an idea of how they would look at nighttime. We'll go ahead and turn our lights off now.The back of the lights are going to be sealed and the housings as well. That makes this light submersible.
However, I do recommend to turn off the power to the light, if you do submerse it. Now, the light's overall length from end to end, is going to be 14 and a half inches. It's going to be one and three sixteenths of an inch wide. And from mounting hole to mounting hole, it's going to be eight and a half inches. And if we look at the depth or the thickness of the light, it's going to be one and five sixteenths of an inch.
So those measurements will help you figure out if you're going to be able to mount this on your trailer. So overall, it's going to be a great replacement and give you that peace of mind, knowing that you're safe and legal. Now as far as the installation goes, it's really easy, especially since we only have one wire to hook up.Speaking of which, let's go ahead and put the light on together now. Before installation, we found a spot back here in the center of our trailer, where we're going to mount up our light. Now, we're actually just replacing this light. The old one that we removed is all beat up and not working anymore. So this one's just going to go in place of it. And since we already had that old light on, all of our mounting holes are actually going to line up.So to get it secured, just line up the holes and then we can grab some self tapping screws and secure it to the trailer. Now, if you don't have holes that line up, you simply just have to drill some out. And I do recommend to use these self-tapping screws to secure it. You can find these here at etrailer, with our lights secured, we can now hook up our wire. So we actually have a small hole here and the frame that we're going to pass light wire through. Get that ran, with a little extra slack, and then we connect it to the trailer wiring. So this black wire here is the one that ran to the original light. So we're going to take our new brown, white wire and cut it to length, and get rid of all that extra wire.We're going to strip that end back, hold it back on so it's a little thicker. And the way that we're going to connect the two is with a heat shrink butt connector. If you need some leads, you can find them here at etrailer. Slide that on to the very end of the wire, crimp it down, and then just connect it to this side of the wire. Once we know they're connected, we can come back with the heat source and seal up our heat shrink. So this is what our butt connector looks like once we have the heat shrink all shrunk down. So I went ahead and just used a little clamp here to secure our wiring to the bottom of the floor. That way we don't have to worry about it bouncing around. So now we can go ahead and hook our trailer up and turn our tail lights on to make sure our light is functioning properly. And that'll finish up our look at and our installation of the Optronics trailer identification, light bar.
Average Customer Rating: 4.8 out of 5 stars (33 Customer Reviews)
14-1/4" Long x 1-3/16" tall. Waterproof identification light bar with 3 replaceable incandescent lights is designed for trailers wider than 80". Polycarbonate lens and stainless steel base. Surface mount. Male 0.180 bullet.Product is an exact replacement for the WESBAR strip light on my Tracker Trail Star Trailer for my 2008 Bass Tracker TXW. Product was very well packaged, communication was excellent, and shipping to receive time was very good. Very pleased with the overall transaction ! Thanks, RB
It looks and fits like the original.
Excellent service as usual
The bar light running lights installed and worked wonderfully on the rear of my Bear boat trailer. They replaced the individual, nonsubmersible lights that shorted out with moisture. I had to drill only one mounting hole and covered remaining marks when mounting. I hardwired, [soldered] the connections, as plenty of wiring was added to the bar lights. Edges of stainless steel was somewhat sharp. The staff was very helpful informing me that incadesent lights are not compatitable to LED lights.
Needed to change a bracket on the old trailer to fit, but works great.
Exactly as advertised. Super quick shipping. One slight problem that was easily resolved - the light bar came with a single wire only, so I had to simply use the existing ground wire and connect it to the back of the bar. No big deal. Works perfectly.
Good price on an great replacement for the original (1998) Wesbar brand lights.
I purchased 3 bars and 2 individual Optonics lights to replace the Wesbars.
Bought this light for a ez- loader boat trailer (04 Skeeter SX 190 ) exactly the same as the old one . And it shipped fast . Thanks etrailer
Products were easy to install and they work great. Very pleased with the results. LED lights are the way to go for your replacement needs.
On time right light
works great as original equipment replacement on EZ Loader
Product arrived in a timely fashion. The product worked good for my application.
Exact replacement parts I needed. Quick shipment and easy to track. Strongly recommend using this company.
Lightbar was delivered quickly and was as described.
Product was easy to install and works g reat
good product, just as described and pictured. very fast shipping and good shipping package. very good service. thank you
The lights are working great.
The item purchased was exactly as described and replaced the OEM part perfectly. Great value as well. Thank you for an easy transaction. A plus.
Products were exactly as I wanted. Excellent descriptions of products on web site. Made ordering easy. Fast delivery, too. Thanks.
Had a tough time finding this locally. Easy install, great price and service
Very fast shipping and a great product. Would recommend to other buyers, for sure.
Part worked great
Purrrfect!!
Great products, wonderful service, knowledgeable & helpful staff!!
good quailty, easy to install & fit perfect
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.