LED Combination Tail Light for Trailers over 80" Wide - Submersible - Red - Passenger Side
(232 reviews)
Price: $31.56
In Stock
LED Combination Tail Light for Trailers over 80" Wide - Submersible - Red - Passenger Side
Item # STL16RB
Retail:$56.03
Our Price: $31.56
You Save: 44%
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (232)
- Q & A (0)
- Photos
Optronics Trailer Lights - STL16RB
- Tail Lights
- Rectangle
- LED Light
- Red
- 8-1/16L x 2-7/8W Inch
- Surface Mount
- Rear Clearance
- Rear Reflector
- Side Marker
- Side Reflector
- Stop/Turn/Tail
- Submersible Lights
- Optronics
8-1/16" x 2-7/8". Waterproof light acts as brake, tail, turn, side marker, side reflex reflector, rear clearance, and rear reflex reflector for trailers wider than 80". Surface mount - hardware included. 3-Wire design. P2 rated.
Features:
- Rectangular trailer tail light serves 7 functions
- Stop light
- Tail light
- Turn signal light
- Side marker light
- Side reflex reflector
- Rear clearance light
- Rear reflex reflector
- Sealed, waterproof construction is submersible
- Durable surface-mount technology (SMT) construction of LED circuit board
- Better withstands shock and vibration
- Allows for improved heat distribution
- LEDs make great replacements for incandescent lights
- Last 50 times longer
- More efficient - provide better light with less power output
- No bulbs to replace - no brittle filaments
- Durable plastic housing with red acrylic lens
- Mounts on surface of trailer - hardware included
- Designed for use on trailers over 80" wide when properly mounted
- 3-Wire pigtail
- DOT compliant
- Meets FMVSS 108 and CMVSS 108 requirements for automotive lighting
- P2 rated
Specs:
- Configuration: passenger's side (right-hand side)
- Dimensions: 8-1/16" long x 2-7/8" wide x 2-13/16" deep
- Diodes: 18 diodes
- Power draw at 12.8 volts:
- Stop/turn signal light: 0.259 amps
- Tail light: 0.062 amps
- Limited warranty on LEDs
Sealed, Waterproof Trailer Light
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The circuit board is sealed, which means that water will not damage the diodes or circuit board.
Combination Lights for Trailers Over 80" Wide
If a trailer is 80" or wider at its widest point, then it requires rear clearance lights in addition to basic trailer lights. These clearance lights indicate the width of the trailer when it is viewed from the back.
To meet these requirements on a flatbed utility trailer where the bed extends past the wheels, you can install combination trailer lights that include the rear clearance function. For proper mounting, the lights must be installed at the widest points on the rear of the trailer - one on each corner.
P2-Rated or P3-Rated Lights
A P2-rated or P3-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
STL16RB Optronics Combination LED Taillight for Marine Trailers More Than 80" Wide - Right Side - Red Lens
Alternate part number: STL-16RB
California residents: click here
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- Wrong item was ordered
- Did not arrive in time
- Product did not meet expectations
Customer Reviews
LED Combination Tail Light for Trailers over 80" Wide - Submersible - Red - Passenger Side - STL16RB
Average Customer Rating: 4.8 out of 5 stars (232 Customer Reviews)
8-1/16" x 2-7/8". Waterproof light acts as brake, tail, turn, side marker, side reflex reflector, rear clearance, and rear reflex reflector for trailers wider than 80". Surface mount - hardware included. 3-Wire design. P2 rated.by: George12/22/2022
Item arrived quickly and as described. Choosing the correct light was easy with the information shown on web page
by: Tom10/21/2023
I have 3rd set of optronics on one boat trailer and the second set on the other boat trailer. In the past year the boats were launched a total 12 times. These newer sets with the coated circuit boards and the 'lite pipes' are working better but not perfect. I have a few LEDs 'out on each side on each trailer. We lived in hope but I guess this is the best we can expect? Thanks Tom
by: John09/14/2023
The mounts broke on the plastic housing where the bolts attch the lights to the trailer. This was only used a few times on a boat trailer with light use and stored in climate controlled garage. I have replaced them with another set.
by: Joshua 03/19/2024
Just what I needed. Had to drill some new mounting holes but these fit perfect.
by: Deborah 03/01/2024
Not exactly like the factory light, but close enough & installed easily.
by: Robert 07/12/2023
Factory wire leads need to be a little longer and ground wire needs to have a ring terminal with an integral heat shrink wrap. The open crimped ring terminal with exposed wire provided on this light will quickly corrode and fall apart on a boat trailer when exposed to salt water immersion. Otherwise, a good quality LED light.
by: Mike 09/01/2023
It was very hard to find what I needed , which I did not find. I ended up with an LED version of my needs and settled for this which worked. However I now have an OEM tail light and a new LED light. It worked so I will live with it.
by: Israel 07/16/2023
Eact replacement to my coastline trailer. Passenger still rocking!! Now just need my drivers side replaced
by: Ralph 04/17/2024
Great value for the money
by: Tullie D04/12/2019
I used these to add auxiliary tail, turn, and stop lights to my pickup truck. I'm very pleased with the results. Hopefully they'll get people's attention.
by: Phil Z11/21/2016
I needed to replace some of the lights on my boat trailer. The old light were incandescent and some of the bulbs had burned out, securing screws were rusted. Product was exactly what I was looking for. Links on each product web page provided very good description and product information.
Thank you for great selection and process.
Phil Z.
11/21/2017
I am very happy, the lights are working great, with no issues. Thank you
by: Hartford06/22/2020
Light worked great up to about two weeks ago. Running light portion of light stopped working. Still have brake and turn single light works. A bit disappointed the full function of tail light does not work. With only a year and less than 400 miles on trailer since tail light was installed.
Heather A.
6/24/2020
I recommend to first make sure the ground wire of the light is is attached to a clean metal surface on the trailer frame. A bad ground will intermittently cause one of the functions to not work properly. If the ground of the trailer does not prove to be adequate you could run it up to the ground circuit of the trailer connector.
by: Marshall H06/08/2016
This light was a much needed upgrade on my boat trailer to make it look more modern and not so old. It is very bright, fit right into the existing holes I used for the old lights and wiring it up could be easier! Have yet to dunk it in the water but I'm sure it will be just fine! Great Product!
Marshall H.
6/8/2017
These lights are awesome. They survived a year of launching the boat over the summer and Im sure theyll survive much more. Bright as well!
by: Al T.05/26/2020
I got these led lights to replace my original trailer lights. Easy to install and a lot brighter, definitely recommend them for anyone wanting to replace there old trailer lights.
Al T.
6/16/2021
Still going strong.
by: Tim10/29/2018
Light arrived damaged. The shipping box does not look damaged. etrailer has sent me a replacement as soon as I called.
Tim M.
10/29/2019
Everything worked out great. Trailer lights are LED bright and are easy to see. Good service and a competitively priced product.
by: Robert10/01/2018
Taillight matched my other trailer light perfectly. Saved me from buying a whole new set. Shipping was super fast and I would suggest your company to anyone who needs trailer products. Will definitely buy from E-trailer again. Thanks
Robert M.
10/2/2019
Actually the lights say they are submersible, but they actually leaked and blew out most of the led bulbs. Would not purchase again.
by: Dan 07/22/2023
Bright and easy to hook up.
by: Kevin 10/06/2022
Product as described and quick shipping. One small item, the carriage bolt fasteners that were supplied were SS material but the nuts weren't. SS is a must for me in salt water service. Otherwise excellent.
by: Bill K08/02/2016
Super tail light! Easy replacement for stock tail light. Took me about 10 minutes to install including soldering leads. I always solder because crimp on connectors always corrode on a boat trailer. Had I used crimp on connectors, would have taken 5 minutes. The LED is bright and easy to see even in bad weather.
by: Mike B04/01/2017
Purchased a set of these lights as replacement/upgrades on my existing standard boat trailer lights. These LEDs lights perform exactly as described. They are completely water tight. After one full year of use, they perform as well as the day I installed them.
by: Neil 08/16/2023
Excellent price, fast delivery and great service.
by: Rich 07/06/2020
Excellent product, Easy to install and electrical hookup. It replaced a busted LED tail light. I leave my trailer lights plugged in when I launch the boat into salt water and have had no problems with the light malfunctioning. Very good light.
by: John07/13/2019
The LED trailer lights truly do make a world of difference. The only thing that I do have to say that is not a positive, is the fact that I had to drill out my mounting brackets on my trailer so these would properly fit. In other words the factory holes on my trailer did not match the aftermarket product. As far as the LED light visibility goes, again there truly is no comparison. The LED lights rock
by: Shawn07/04/2016
There were a perfect fit replacement for my 1992 Tracker Trailstar boat trailer. It had Wesbar 3348 tailights on it. These look exactly the same but they have sealed LED capsules inside. It was gonna be the same price to replace the old style bulb capsules in the Wesbar's as it was to but these whole brand new sealed LED tails. The are very clear and bright. Huge improvement!
by: Ron T (Va)09/13/2016
Flawless throughout the year bouncing along the highway and loading and unloading my boat in frigid water. Twice as bright as my previous "sealed capsule" tail lights, which I would have had to replace 2-3 times in that period.
Wish I had found them years ago!
25
232
Show More Reviews
See what our Experts say about this Optronics Trailer Lights
- Replacement Tail Lights Included In TLL16RK Kit for Trailer Over 80 Inches The tail lights that are included in the # TLL16RK kit you referenced are # STL16RB for the passenger side and # STL17RB for the driver's.
view full answer... - Troubleshooting Tail Light Issue on a TrailerThere are a few different things that could cause taillight failure. Issues that you will want to look for are a weak ground connection, a short on the taillight wire or a possible issue on the vehicle side. To start, I like to test the trailer connector on the tow vehicle to make sure power is reaching the trailer. I recommend using a circuit tester with an incandescent bulb, like part # PTW2992. You will want to test the pin on the trailer connector for the taillight function. If you...
view full answer...
- LED Trailer Lights Troubleshooting Lowes Trailer And 2008 Ford F-150Since you have already checked some of the first troubleshooting boxes, the next place to look is if the harness has been overloaded due to excessive draw from lights or there's a short in the trailer wiring. Inspect the wiring for any damaged areas where copper is visible or any spots where the jacketing on the wire is broken and replace as necessary. If you've already taken this step, I would next check your harness instructions for maximum amperage rating to make sure you're not overloading...
view full answer... - Trailer Taillight Lens Recommendation to Replace AISTP2 85If your tail lights look like # STL16RB or # STL17RB, then you can use the Replacement Tail Light Lens, # A16RB.
view full answer... - LED Trailer Taillight Recommendation that Has License Plate LightThe Bargman 84 and 85 series taillights like the # 47-84-610 that you referenced don't have a license plate light, so a better option will be the # STL17RB for the left hand side light and then part # STL16RB for the right hand side. Then for a license plate bracket you would want the # LP5SB. The # STL17RB has a license plate light.
view full answer... - Triton Utility Trailer LED Light ReplacementI pulled up pictures of your Monarch trailer lights and the closest LED taillight assemblies we carry are the part # STL17RB for the driver side and part # STL16RB for the passenger side.
view full answer... - Replacement Tail Light Lens on a Snowmobile Trailer with Optronics Tail LightsIf your tail lights look like # STL16RB or # STL17RB, then you can use the Replacement Tail Light Lens, # A16RB. This is the correct replacement for the tail light. If the lens portion is deeper on your lights than those pictured, you may have a 26 series light like # STL26RB as an example. The 1/16 of an inch would be the very first tick mark after the 8 inch line on a ruler (provided the ruler measures in 1/16 increments). Both my Staples ruler and Craftsman tape measure use the 1/16...
view full answer... - Replacement Passenger Side Tail Light for Sun Tracker TrailerIt definitely looks like you need a new tail light assembly for your 2017 Sun Tracker trailer. I recommend the LED Combination Tail Light for Trailers over 80" Wide - Submersible - Red - Passenger Side # STL16RB because of its long-lasting, bright LEDs, easy surface-mount and its waterproof housing. It may be a good idea to replace your driver's side light as well with the accompanying LED Tail Light for Trailers Over 80" Wide - 8 Function - Submersible - Red Lens - Driver # STL17RB, or...
view full answer...
- Replacement LED Submersible Trailer Taillight Recommendation for 2007 Stratos TrailerYes, the LED Tail Light for Trailers Over 80" Wide # STL17RB and # STL16RB would work well for your 2007 Stratos 176xt carrying trailer. These lights are submersible which means that all of the circuits are waterproof and protected from the water but water will run through just the housing of the light. I attached a review video for this light for you to check out as well.
view full answer... - Number of Diodes in Optronics Trailer Taillights STL16RB/STL17RB and STL36RB/STL37RBThe trailer taillights part # STL16RB and # STL17RB have 18 diodes and the tailligths part numbers # STL36RB and # STL37RB have 17 diodes so they are very similar.
view full answer... - Replacement Taillight Recommendation for 1997 Tracker TrailstarI pulled up as many pictures of your trailer as I could off Google and it looks like the taillights you would need are part # STL16RB for the passenger side and part # STL17RB for the right hand side.
view full answer... - Recommended Replacement Taillights for Shorlandr Boat TrailerThe best option we will be able to offer for taillights for a Shorlandr boat trailer is a new set of matching taillights and for this I recommend LED Combination Tail Light part # STL17RB for driver side and part # STL16RB for passenger side. These lights are seven/eight function and measure 8-1/16" long x 2-7/8" tall x 2-13/16" deep. I won't have any good replacements to match up to the part you listed unfortunately. I have attached our full section as well if you would like to opt for...
view full answer... - How to Combine Stop and Turn Signals for Flat Towing with a Diesel PusherTo combine the stop (brake) and turn signals on your diesel pusher you will need to use a converter like the Roadmaster Brite-Lite Converter # RM-732. Simply connect the individual signals to the one end and then connect the wires with the combined wiring to the correct points on the 7-Way. I have attached a photo showing the typical signal locations for a 7-Way. If you were to toss a jumper wire between the stop and turn signal functions then it would cause your lights to receive mixed...
view full answer...
- Will the ST17RB Over 80 inch Rectangular Submersible Trailer Tail Light Fit on a LoadRite TrailerI did some research online and found that the LoadRite trailer very well could use a light like the Over 80 inch, Rectangular Submersible Trailer Tail Light, # ST17RB (left) or ST16RB (right). LoadRite uses several different styles of light and have recently gone to LED lights on many of their boat trailers. If your trailer is newer and has LED lights you would most likely need the, # STL17RB and # STL16RB, lights to replace the original lights. I pulled the # ST17RB light and did a short...
view full answer... - Trailer Lights for 12 Volt and 24 Volt Systems on a 1994 Mercedes G Wagon and Honda CR-VSome trailer lights can be used on either a 12 volt or 24 volt system, but # STL16RB is not one of them. You could use # STL23R24B with harness # A47PB, grommet # A45GB, bracket # BK45BB for a 24/12 volt system and it would work with both vehicles.
view full answer... - What is the Matching Right Hand Tail Light for Trailer Tail Light # STL17RBThe matching right hand light that you will need is # STL16RB. We also have these lights together in a kit, # TLL16RK. The kit comes with a license plate mounting brackets, mounting hardware, and a 25 foot wiring harness with 4-Way connector. I have included a link to a video showing a typical installation for you.
view full answer... - Single Submersible LED Tail Light For Over 80 Inch Wide TrailerThe Waterproof Over 80" LED Trailer Light Kit with 25' Wiring Harness # TLL16RK does have the parts available separately. You can get # STL16RB for the passenger side or # STL17RB for the driver's side which includes the light for the license plate so it is 8 functions instead of 7.
view full answer... - Parts Needed to Add Combined Tail Lights to Trailer with Separate Turn SignalsSince you currently have separate tail lights on your RV and plan to install an additional set of combined lights you'll need to use a signal converter like part # RM-732 to get the signal correct. Basically you wire this to the lights you currently have and then you'd have the combined circuits ready for your new taillights like the # STL16RB that you referenced.
view full answer... - LED Tail Lights for a Ranger Trail XT188 Boat TrailerI checked with Ranger and the current generation of the Trailer RT188 uses the 6 inch oval tail lights. For those the Miro-Flex Trailer Tail Light # STL22RB is a great option for an LED upgrade. These lights use pigtail # A47PB and will fit the mounts currently on the trailer. If your trailer has different tail lights, such as those that hang from studs then # STL16RB and # STL17RB are great options for that mounting style. If neither of the recommendations above are the light style or...
view full answer... - Using Trailer Wiring Harness on a Honda CR-V All Trailer Lights Stay OnOn the trailer lights, white is ground, yellow or green is the turn signal function, and the yellow or green with brown is the running lights. Check to make sure that everything is wired to the correct wire from the trailer side 4-Way. The lights should be grounded to the trailer frame near where they are mounted. Try removing the additional ground from the lights back to the vehicle. This does sound like a ground issue. Unplug the trailer and use a circuit tester like # PTW2993 if needed...
view full answer... - LED Replacement Lights for Wesbar 102640For and LED replacement for your Wesbar 102640 I recommend the Optronics LED Combination Tail Light for Trailers over 80" Wide. This light measures 8-1/16" long x 2-7/8" wide x 2-13/16" deep. You will need the # STL16RB for the passenger side and the # STL17RB for the driver side.
view full answer... - Replacement Taillight Lens Recommendation for EZ Loader Star Craft TrailerI looked up several pictures of your ez loader Starcraft trailer and they all had taillight assemblies like the part # STL16RB that you referenced which means that for replacement lenses you would need the # A16RB.
view full answer... - Troubleshooting LED Trailer Light InstallationThe first thing I would do is check that the white ground wire is attached solidly to a clean metal surface on the trailer frame. A bad ground will prevent a light from working, if the ground of the trailer does not prove to be adequate you could run it up to the ground circuit of the trailer connector. The next thing you will want to do is make sure that the # STL16RB is wired correctly by function and not just by wire color. Normally the colors of a 4-way will be the standard colors...
view full answer... - Converting Separate Turn Signals and Brake Lights to Combined Turn and Brake Lights on a TrailerIf the trailer is one that is pulled by a motorcycle or a trailer designed to carry a motorcycle, you will need a converter in order to convert the wiring system used by the 6-Way to a 2 wire system used by trailer lights. The converter you can use is # RM-732. This takes the separate turn and brake signals and makes them a combined circuit. When you hit the brakes with the turn signal on, it should blink on one side and the other side will remain a solid brake light. The converter will...
view full answer...
Do you have a question about this Trailer Light?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Reno H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Jeffrey L
Video Edited:
Jacob T
Updated by:
Adele M
Updated by:
Laura H
Updated by:
Amy B
Updated by:
Wilson B
Video by:
Kathleen M
Video by:
Dustin K
Installed by:
Cole B
Installed by:
David F
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
George S.
12/23/2023
product has functioned properly and going strong