Hook and keeper door holder securely holds your RV or trailer door open. Constructed of zinc-plated steel and measures 6" long. Includes mounting screws.
Features:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Colin: Hey guys, it's Colin here at etrailer and today, I'm just going to take some time to show you guys these JR Products hooking keepers. Basically, what these are going to do is just hold the side door or the back swinging doors of your enclosed trailer or camper open so that you can go in and out with ease, don't have to worry about opening the door every time you want to go in. So for days like today where there's actually a breeze going, what we can do is just open up the door, put the wand into the keeper just like that, it's very simple. And from there, it's just going to hold the door open so we can go in and out, load and unload as we please.Now with these certain hooking keepers, a six inch version, they are available in a lot of different constructions and colors. For these plastic ones, you can see we have the Polar White which matches our trailer very well. We have this Colonial White in the middle and then black as well, so you can choose the one that's going to best match your trailer, whichever one you want.
Now, we also have them available in both stainless steel, which is right here, and a zinc-coated steel. It's going to look very similar. These are going to be a little bit more tough and durable. The plastic ones, while they are going to be more flexible and maybe a little bit easier to use at times, they won't last as long as the steel ones. So, just pick the one that's going to best suit your trailer.
They're all going to do a great job.Now, whichever one you go with, you are going to get the mounting hardware included. Now, obviously you can see, we did not use the mounting hardware in this application. That's just because we had to replace a previous hooking keeper. And the holes that we're already drilled out we're bigger than what these screws will fit. So, we had to pick up some different self-tapping screws that we're just laying around the shop.
Either way, you just want to make sure you get it installed and secured.Now, the wand length on these keepers is going to be six inches. That's relevant because if you have any mounted on your doors, on the sides it's usually not going to be as big of an issue, but for the back doors, you can see we got these tail lights, license plate lights. You want to make sure those aren't going to make contact with your trailer when you put the keeper on. So with the back doors, we already have keepers installed and we don't have to replace them. So, I'll show you what I mean by that by opening up this door.So you can see those lights are getting pretty close to our trailer.
This is a 4-inch wand, so we are just able to get it hooked in without the lights making contact. So you definitely don't want to go any shorter than that 4-inch wand that we already have installed. If you don't have anything on the back of your door and you want to go even more flush against the side of your trailer, we do even have shorter wands available here for each of them, if that's what you're more interested in.And this is a nice and simple investment you can make. It doesn't cost a ton of money to be able to get your doors held open so they don't swing and hit you while you're trying to load and unload your trailer. That can be a real big frustration and just make your day that much worse. Now, I'll go ahead and walk you through how to install it real quick; it's nice and simple.Now, you can see the spot where our previous hooking keeper was installed, that just kind of faded and eroded over time, so it wasn't very useful anymore. So, we just took it off. We have these preexisting holes in the hardware that came with it. Like I said earlier, it didn't fit. So, we're just using these other self-tappers that are going to make the hole slightly bigger. So, let's just go and get it installedAnd then, we'll get the wand side installed also. There we go. Let's go and open up our door and test it out, make sure that it works. Hook it on, just give it a good push. You see that it's holding, so we're good to go. And that's all there is to it. It's a very simple install. So from here, what we can do is just close our door up and hit the road.Well, I hope this information helped you out, but that's going to do it for our look at these JR Products hooking keepers.
Average Customer Rating: 4.9 out of 5 stars (28 Customer Reviews)
Hook and keeper door holder securely holds your RV or trailer door open. Constructed of zinc-plated steel and measures 6" long. Includes mounting screws.Great products and very fast service
should work if I can remove the old plastic pieces
Good, heavy quality materials. It has been super easy to customize to my enclosed trailer. A variety of accessories has made the process of setting everything up a breeze!
As usual. Quality parts for a great price. Thank you guys
Great quality & durability, especially vs the plastic one that came with the trailer!!
I was very pleased with Etrailer.
Exactly what I was looking for. Took a while to get here, but I am satisfied
Excellent service, I re eived exactly what I ordered in a very timely manner.
Everything came in as ordered on a timely mannor , Thank You so much !
So much better then the plastic!
Works perfectly. Just as advertised.
Quick and easy
Quality seems good for the price
Do you have a question about this Trailer Door Holder?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.