Availability of Replacement Parts for Ventline Rounded Dome Trailer Roof Vent

Question

Question:

I have the ventline rounded dome. I was looking for the replacement screen, beauty ring, and the gasket, then thought I could just buy the whole thing and pull off what I need. I purchased one in Campworld, only to find the screen does not line up with the old hole on the crank. I see plenty of replacement lenses, what happens when I need the entire assembly. Cost more to piece meal, looks like thats what I need to do. Also you screens do not have the dimmension from the edge to the handle. I just want to make sure Im getting what I need the first time around.

asked by: Don

1

Helpful Expert Reply:

The Ventline product you reviewed, part # V2092SP-28, is a complete vent assembly intended for a rough roof opening of 14-1/4 x 14-1/4 inches. It consists of a wedge-shaped white plastic dome attached to a galvanized steel frame with hand-crank assembly, a removable screen, and a white plastic 2-1/8-inch-deep garnish (interior trim ring).

Please note that this part requires an installation kit, part # 344270KITW, which consists of mounting hardware and a urethane caulk sealer. If your trailer roof thickness requires a deeper garnish we also offer a 5-1/8-inch version, part # VA0445-37, and a 3-1/8-inch version, part # VA0445-35, which are available separately. We also offer replacement dome seal weather strip, part # BVD0455-01.

I pulled a piece of this vent kit from inventory in order to provide you with the screen measurements. Please refer to the photo included which shows the removable screen and its dimensions. Please note this screen is available as a stand-alone replacement part, item # BVD0434-41.

We also offer a 12V fan-equipped version with manual dome lift, part # V2094SP-30. This also requires the installation kit and can also be used with the other sizes of garnish. Wiring is not included but we offer 16-gauge primary wire, part # DW02359-1, and butt connectors, part # 05731-5. Note that this unit also has a wedge-shaped dome.

If neither of these items is suitable for your trailer, please provide photos of your existing vent and details on your trailer vent opening (and part numbers from the original parts if possible) and I will be glad to research further and contact Ventline to see if they have alternatives to offer.

expert reply by: Adam R

1

click to enlarge

Answer 1

The Replacement 12-Volt DC Fan Motor, #BVD0218-00, is a replacement for specific Ventline Ventadome or Vanair RV roof vents. The specific model numbers are V2094, V2119 and VP-543. If you have a different model this motor will not be compatible. The…

view full answer...

Answer 2

The correct replacement motor you would need for your V2094 Vent is the part #BVD0218-00 that you referenced. Based on what you described it sounds like you may have damaged the old motor when you attempted to clean it.

view full answer...

Answer 3

I do have some great full replacement options for you but the motors are not replaceable on trailer tongue jacks. There might be one or two out there which are but none of the dozens we carry ever have that option. Instead, I recommend the Phoenix…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...