Power Wire Kit for Electric Trailer Brake Controllers - 12 Gauge

See what our Experts say about this etrailer Accessories and Parts

• No Power to P2 Brake Controller in 2019 Ford F-150
  Hey Scott; with some models of the 2019 Ford F-150 power was not run to the brake controller port under the dash for some reason. So you'll want to use a circuit tester and test the black wire on the brake controller connector to see if you're getting power. My guess is you won't so you'll have to Power Wire Kit for Electric Trailer Brake Controllers # BRK-ELECKIT to get power to the port. I have added a link below to a video of this part for an F-150 which may help.
  view full answer...
• Solution for Powering Brake Controller Install of 2019 Ford F150 with Factory Tow Package
  This is a common issue for installing a brake controller in the 2019 Ford F-150 and the easy solution is to install the part # BRK-ELECKIT which bypasses the very mysterious brake controller power wire issue your truck has and allows your brake controller to draw power directly from the battery. Basically you cut out the black wire from the harness you have now and connect it the wire of this kit and then wire it directly to the battery with the included ring terminals. This bypasses the...
  view full answer...
• Can a Trailer Brake Controller be Turned Off
  Modern brake controllers such as the P2 # 90885 will go into a power saving mode after about 15 minutes of inactivity. In this mode the controller will only draw a few milliamps of power. At that rate it would take months of the vehicle just sitting for a brake controller to drain the vehicle battery. If it does not go into power saving mode that means that something is drawing power on the brake circuit. The most likely culprit is corrosion in or on the vehicle side trailer connector....
  view full answer...
• What Parts Will I Need to Install a Tekonsha Brake Controller on 2021 Ford F-150
  To install the Tekonsha brake controller on your 2021 Ford F-150, you will need a wiring adapter like the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers # 22292. You can use this adapter if your F-150 has the factory 4-Flat or 7-Way. If you can tell me the model number of your brake controller and if you have factory tow package or not, I can tell you the exact adapter you will need.
  view full answer...
• Does Computer of 2019 Ford F-150 Need Flashed to Install Aftermarket Brake Controller?
  If you install the Prodigy P3 # 90195 you will not need to have the computer flashed. In most models it will simply plug in using the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers # 22292, however some do not have power run to the brake controller port under the dash. If this is the case, we have wiring kit # BRK-ELECKIT which you can use to run power to the brake controller port. I've attached a video to help with all of this.
  view full answer...
• Location of Brake Controller Connector for an Aftermarket Controller on a 2018 Ford F-150
  The location that you would connect an adapter like part # 22292 to your 2018 Ford F-150 for installing a brake controller like the Prodigy P3 # 90195 is behind and to the left of the center console area. If you remove the front panel that is directly under your steering wheel you can access the plug this way (see attached photo). Some models of the 2018 F-150 don't have power running to this brake controller port. If this is the case for you then you would need the wiring kit # BRK-ELECKIT...
  view full answer...
  
• Can A Tekonsha Brake Controller Be Installed On a 24 Volt Electrical System
  Yes, it is possible to install a Tekonsha brake controller like the Tekonsha Primus IQ Trailer Brake Controller part # TK90160 which is what I recommend on a 24 volt system. In order to do so you will need to obtain a 24 volt relay from your local automotive parts store and then some various primary wire, circuit breakers, and wire connectors like what is included with the Power Wire Kit for Electric Trailer Brake Controllers part # BRK-ELECKIT. I have attached a diagram for you to assist...
  view full answer...
  
• Brake Controller Recommendation for 2018 Ford F-150
  To install our very popular P3 brake controller part # 90195 in your 2018 Ford F-150 will only require the correct install harness. For that you'd want the # 22292 which is a confirmed fit and simply plugs in under the dash. Some versions of your truck though don't have power ran to the brake controller port and would require you to also install the # BRK-ELECKIT. I attached an install video for this for you to check out as well.
  view full answer...
• Will the Curt Echo Brake Controller Work On a 2019 Ford F-150
  The Curt Echo Mobile Trailer Brake Controller part # C51180 will work with a 2019 Ford F-150. However, the 2015+ Ford F-Series Pick-Ups have what is called a SmartTow feature that prevents power from supplying the trailer connector most of the time. Therefore, in order to use the Curt Echo on a 2016 Ford F-150 you will need to run a dedicated power wire from the battery to the trailer connector and all you will need for this is the Power Wire Kit for Electric Trailer Brake Controllers part...
  view full answer...
• Parts Needed to Run Power Circuit for Installing Curt C51180 Curt Echo Wireless Brake Controller
  Using 12 ga wire is indeed acceptable for installing the Curt # C51180 Echo wireless brake controller, but to protect the power feed circuit you'll want to use a 30A self resetting circuit breaker instead of a fuse. We sell the wire, hardware and breaker in a kit, as part # BRK-ELECKIT. If you already have the wire and hardware, we sell the breaker separately as part # 38630.
  view full answer...
• Which Circuit Breaker Needed to Install Curt C51180 Echo Brake Controller on 2012 Toyota Highlander
  If you'll be installing the Curt # C51180 Echo Wireless Brake Controller, you'll want to use a 30A breaker, like part # 38630, you'll also need 12 gauge wire, ring terminals and butt connectors. We actually sell all this in a kit as part # BRK-ELECKIT. I've linked to a video explaining how the Curt Echo brake controller works, as well as to a video that will run you through the install.
  view full answer...
• Installation of Brake Controller and Brake Controller Wiring to Added 7-Way in 2018 Ford F-150
  For your 2018 Ford F-150 I don't recommend the Curt Venturer but it will install in the same way as any other brake controller and for that installation you have a couple different options. If when you installed the 7-way you grabbed the factory wiring for your 12V and brake controller from near your driver's side wheel well, then I recommend using the wiring harness which will connect to the factory port under your dash. Some models don't have the brake controller power wire run under...
  view full answer...
• Tekonsha TK90160 Primus Brake Controller Not Powering Up When Installed in 2020 Ford F-150.
  For whatever reason, some F-150 models will have the plug in the dash for the brake controller, but the 12 volt power feed to that connector hasn't been connected. You may need to add a 30A fuse in the distribution box under the hood, in location # 24. If location # 24 is NOT pinned, you'll need to run your own wire to the controller. We offer a kit, part # BRK-ELECKIT that will correct this. I've provided an install link for a different controller, but the procedure for your # TK90160...
  view full answer...
• ETBC7L Without 7-Way for Autowbrake Brake Controller
  There is a kit that has exactly what you need with the hardware without the 7-way of the RV Upgrade Kit # ETBC7L. What you need is the Power Wire Kit for Electric Trailer Brake Controllers # BRK-ELECKIT. This has everything you are looking for, minus the 7-way, so you can install the Autowbrake Electric Brake Controller # 3430001. In regards to the power wire, it will not charge the trailer battery, but it will maintain the battery's charge while you are towing.
  view full answer...
• Are Some Versions of the 2021 Ford F-150 Not Able to Have Brake Controller Installed
  On some models of the 2021 Ford F-150 the brake controller install port is present but there just isn't any power ran to it for some reason. The solution for that is to use the part # BRK-ELECKIT which gives you the parts needed to activate this circuit. Basically it's a 12 gauge wire with a circuit breaker that runs up to the vehicle battery. To install the # TK90160 you referenced you'd also need the part # 22292 then. We've also seen that the versions of the 21' F-150 made earlier...
  view full answer...
• Curt C51180 Echo Wireless Brake Controller Showing 'Vehicle Battery Low' Error
  I believe the reason your controller is behaving the way it is is the lack of a direct battery connection. Pressing the brake pedal feeds some power to the unit that disappears once you let off the brake pedal. In order for the Curt # C51180 to work correctly, it does indeed need a direct battery connection for the pin in the 1:00 position on the 7-way trailer connector. If you don't already have a direct connection, you can set it up using # BRK-ELECKIT which includes the 30A breaker...
  view full answer...
• Adding a 7-Way Connector and Brake Controller to a 2018 Ford F-150 with Factory 4-Way
  I will be happy to get your 2018 Ford F-150 set up with a 7-Way trailer connector and a brake controller. The method for doing so that requires the fewest parts is to hardwire in the brake controller/7-Way. Since your truck already has a factory 4-Way connector you will just need # ETBC7 to add a 7-Way, retain the 4-Way, and have the parts needed to install a brake controller as well as run a 12 volt hot lead. If you do not already have a brake controller picked out I recommend the P2...
  view full answer...
• Parts Needed To Install 7-Way To Power Curt Echo On 2018 Hyundai Santa Fe
  The reason your Curt Echo # C51180 is not working is because it doesn't have 12V power. When you connected the 4-way to the 7-way adapter all it did was carry over the 4-way functions. This is also why your lights still work. The black wire coming off the the 7-way adapter should be the 12V power wire, which runs to the pin in the 1 o'clock position you described. In order to make this happen, you can use the Power Wire Kit for Electric Trailer Brake Controllers - 12 Gauge # BRK-ELECKIT....
  view full answer...
  
• Troubleshooting a Curt Venturer Trailer Brake Controller in a 2020 Ford F-150 with Tow Package
  I took a look at the Curt Venturer NEXT Trailer Brake Controller # C74VV and Curt Custom Wiring Adapter for Trailer Brake Controllers # C51436 that you have. It is a little odd that you have power and it works with the manual over-ride but not with the brake pedal. My first instinct was that your brake controller port didn't have power, that is somethin that can be a problem on that model and is fixed with the Power Wire Kit # BRK-ELECKIT, but if you have power that isn't it. Looking...
  view full answer...
• Does Computer Need To Be Flashed When Installing Brake Controller On 2021 F150?
  The OEM brake controller requires your 2021 Ford F-150 to be flashed by the dealer. However, an aftermarket brake controller like the Curt Assure Trailer Brake Controller - # C49UR does not require the dealer to flash your truck's computer. You will need Plug-In Wiring Adapter # C51436 to connect the brake controller to the factory plug-in on your truck. Keep in mind, not all 2021 models have the necessary 12V going to the plug-in, so you may end up needing to install Power Wire Kit for...
  view full answer...
• Recommended Air Brake Controller Compatible With Electric Over Hydraulic Brake Actuator
  We have exactly what you need. You will want the Hayes Air Actuated Trailer Brake Controller - 1 to 4 Axles - Proportional # HA100400C which is the only Air to Electric brake controller we carry that is compatible with electric over hydraulic brake actuators. For this installation I also recommend the Power Wire Kit for Electric Trailer Brake Controllers - 12 Gauge # BRK-ELECKIT and the Air Line Hose 1/4" # RM450700 sold by the foot. The similar Warner Air Utility Brake Control # 1300-80...
  view full answer...
  
• Recommended Base Rail Kit For A 2019 Ford F-150 Short Bed
  Having installed universal rails in an older F-250 I can say with complete confidence that the money saved isn't worth the time you'll spend trying to drill through the frame to get all the bolts through, especially if you don't have lifts to make the job easier. I recommend going with the Curt Custom Fifth Wheel Installation Kit for Ford # C93WR instead. This custom-fit kit uses the holes already in the frame to minimize drilling for a quicker and easier installation. I've attached a...
  view full answer...
• How to Wire Curt C51180 Echo Brake Controller for Power
  It's pretty simple to install the power connection for the Curt # C51180 Wireless Brake Controller. We actually offer a kit that offers everything you need, part # BRK-ELECKIT. The kit includes the wire, inline circuit breaker, hardware and even the zip ties needed to complete the installation. We also offer a full kit that includes the 4 pole to 7-way adapter as part # ETBC7L. I've linked to an install video and a help article that you might find helpful.
  view full answer...
• Redarc Tow-Pro Elite Brake Controller For Towing A Horse Trailer With a 2021 Ford F-150
  The reason that the Redarc Tow-Pro Elite Trailer Brake Controller # RED44FR is not good for the manual override is that when you drive with the controller in proportional braking mode and push the manual override it only allows the trailer brakes to be applied in a light braking scenario. This is often not enough braking force on the trailer brakes if you are relying on them solely. As you are new to trailering and brake controllers I do not see this being an issue for you as it comes more...
  view full answer...

Do you have a question about this Accessories and Part?