Grease Cap Plug for E-Z Lube Grease Caps - Qty 2
(1236 reviews)
Price: $4.42
In Stock
Grease Cap Plug for E-Z Lube Grease Caps - Qty 2
Item # RG04-010
Our Price: $4.42
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (1236)
- Q & A (0)
- Videos (2)
- Photos
TruRyde Accessories and Parts - RG04-010
- Trailer Bearings Races Seals Caps
- Plugs
- TruRyde
Replacement Trailer Grease Cap Plugs for E-Z Lube Grease Caps
- Rubber lube plugs for 1.18" dust cap hole
- Quantity: 2
RG04-010 TruRyde Rubber Lube Plugs for 1.18" Lubed Dust Cap Hole
Video of Grease Cap Plug for E-Z Lube Grease Caps - Qty 2
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for TruRyde E-Z Lube Grease Caps Plug Review
Hey everybody, Ryan here at etrailer. Today we're gonna be checking out the true ride plugs for EZ Lube grease caps. So right off the bat you're probably wondering are these actually gonna fit my trailer And as long as you have the EZ Lube grease caps chances are really good they will. There are a bunch of different manufacturers that make these caps but generally speaking they're all gonna have the same size opening there. So if you pop this one out, like I said majority of them are gonna be the same. So 1.18 size opening.
So if you're unsure, you can measure that and figure that out really. And the whole point of the cap, you know the grease cap and this plug, is allow to you to pop that out like I just did. Get your grease gun in there and lube up all of your parts inside of there with ease. And then, you know, obviously you don't wanna leave that exposed. So the cap will pop back into place.
And these things are really tight too. So I feel like they do a decent job of keeping everything sealed up. To me this is just one of these small parts. It's just good to keep, you know, replaced every now and again. What happens over time They just wear out, you know what I mean They get sun faded, kind of start to dry rot.
You know, if you're in and out of the water with em, and this is a good example of one that's several years old. It's started to dry rot, try to push it in place, and the center of it just pushed through. So, you know, if you're cap and everything's still in good shape, you can get away with just get the the replacement plugs like this one here that way put it in, keep everything sealed. And that way, you know, you don't end up chewing your bearings up, getting dirt and everything else inside of there. And I was replacing one, I would probably just replace 'em all.
You know, it's one of those small things to just, just knock 'em all out. Like that's just me. And I mean, you know, the type of stuff happens. Like I said, they just wear out, you grease 'em forget to put 'em back in. Whatever the case may be at the very least, there's an option available that you can grab these and get fixed back up. The plug does feel like it's made from some type of rubber, pretty thick. Like I said, I feel like it should hold up for quite some time. That one I just had was super old. So I got a lot of life out of it. But other than that though, I mean, at the end of the day you know, that's really about it. Regardless if you need these, or let's say, even if you're looking for the whole whole deal, you need the cap as well. Tons of different options available here at etrailer. So regardless on the small ins and outs that you need, we should be able to get you covered. And that'll finish up our look at of the true ride plugs for the EZ Lube grease caps..
Customer Satisfaction Score:
100% were satisfied with this product
0% of customers were not satisfied
- Did not arrive in time
- Wrong item was ordered
- etrailer mistake
Customer Reviews
Grease Cap Plug for E-Z Lube Grease Caps - Qty 2 - RG04-010
Average Customer Rating: 4.9 out of 5 stars (1235 Customer Reviews)
by: G04/04/2024
fit well, excellent price compared to brick & mortar local sources.
love the EZ-lube axles, not a fan of how these rubber plugs deteriorate, crack and come apart.
Now we have a source.
Thx
by: Keith02/12/2024
THEY HAD MY PURCHASE HISTORY @ THEIR FINGERTIPS! I'M NOT THRILLED ABOUT THE DURABILITY OF THE CAPS. I ONLY REPLACED THEM 3-4 YEARS AGO, AND THEY SEEM TO BE GETTING PRETTY SPONGY. THEY NEED A DIFFERENT MATERIAL THAT WON'T REACT WITH THE BEARING GREASE
by: Thomas 04/13/2024
Needed to replace the originals they sometimes get a hole when removing to grease the axil. These are a good replacement.
by: Kenneth 02/14/2024
Great affordable way to keep your hubs on. They have been in my trailer for about a year and they are still in good condition.
by: Jim C06/30/2014
I tried this product for an aviation application. I own a DHC-2 Beaver aircraft that has a tail wheel axle that is 1.125 inch ID. I wanted an end cap that was removable because the axle tube is used to steer the aircraft with a hand held bar during some ground movement. So far the rubber cap seems to work. It has remained on during several flights. It is easy to remove and insert. The only problem may occur if the cap mounting area of the axle become oily or greasy which may allow the cap to slip off. It seems to need a friction fit to stay on.
by: Dennis 03/06/2024
Replaced my old the grease cap plugs on my boat trailer. Fit perfectly.
by: Eugene04/21/2024
So far so good. These plugs are good replacements for my old ones that started to leak grease. They fit the 1.18 inch hole and seem tight.
by: David 03/24/2024
perfect fit for the ezlube hub
by: Stephen 04/24/2024
Perfect fit on my Dexter axles!
by: AC12/29/2023
Holds up better than the original off my 24ft enclosed trailer. No issues even after one year of being beaten by the Arizona sun.
by: Scott 04/01/2024
The price was very reasonable. Fast ship time too. I've always had great luck with etrailer.
by: Kevin 04/12/2024
Worked perfectly! Quick delivery. I will continue to use etrailer!
by: Christy 03/25/2024
These guys are great. Good quality and very fast shipping. They always seem to have what we need. Thanks
by: Leslie W03/05/2024
Seee review for grease seals.
by: Terry 04/26/2024
They seem a little smaller than the original caps. I am using then and hope they hang in there.
by: Jason 03/23/2024
Always great doing business with etrail er
by: Bryan 02/13/2023
Excellent. Fit tightly and are a much better quality than the original
Bryan
2/14/2024
Great
by: Kevin 01/30/2024
better quality than what came new on my dexter axles and a perfect fit
by: Tim 02/10/2024
Always excellent prompt service from you Trailer. Thank you.
by: Maureen 04/23/2024
Exactly what ineeded
by: George 09/11/2023
The grease cap plugs appear to be heavy enough to perform as desired. I'm a suspenders and belt kind of guy so ordered 3 sets. I hope I didn't need them all before I get too old to pull a trailer.
by: Richard 08/05/2022
Grease caps - fit, work as designed
Richard
8/5/2023
Grease Caps - still fit, still work as designed a year later. Removed & replaced twice to add grease to hubs. The caps remain flexible, no drying or UV cracking. What more do you want? They are grease caps. Oh, I get it ... These etrailer grease caps have changed my life. I lost 135 pounds since I bought them - Oh wait ... that was the x-wife and the divorce ...
by: Jordon05/03/2024
I bought a good quality item, a good price and very fast shipping - I highly recommend!
by: Austin 02/03/2024
Worked great.
Austin
2/15/2024
This product is great. Awesome customer service.
25
1236
Show More Reviews
See what our Experts say about this TruRyde Accessories and Parts
- Availability of Trailer Hub Grease Cap that Fits 1.98 inch DiameterFor a trailer hub grease cap that fits a diameter of 1.985 inch you'd want the part # 21-41-1 and then for the rubber plug that fits the center of the cap is the part # RG04-010.
view full answer... - Is TruRyde Grease Cap Plug Correct Part?The Grease Cap Plug for E-Z Lube Grease Caps # RG04-010 is the correct replacement grease cap for your Dexter 85-1 plug; both are plugs for 1.18" hole. I've left a link to a video review of this product for you to take a look at.
view full answer... - Replacement Rubber Plug for EZ-Lube Grease Cap on Tow DollyThe only rubber dust covers we offer for EZ Lube grease caps are # RG04-010, which are designed to fit a 1.18 inch diameter hole in the grease cap to allow access to the grease zerk without removing the cap. Your best bet would be to simply replace your existing grease caps. If the outer bearing is # L44643 or # L44649, use the # RG04-040 grease cap with removable plug. This is compatible with most 2000-3500 lb capacity hubs which is typical of what's found on most tow dollies. To be...
view full answer... - What Size Grease Cap Hole Does Grease Cap Plug for E-Z Lube Grease Caps, # RG04-010 FitThe Grease Cap Plug for E-Z Lube Grease Caps, # RG04-010, is designed to fit Dexter E-Z Lube grease caps on the Dexter E-Z Lube axles like # RG04-040, and will otherwise fit a 1-1/4 inch opening on a grease cap. The Rubber Lube Plug - Fits 1.18 Inch Lubed Dust Cap - Qty 1, # DC-RP, fits a 1.18 inch dust cap hole and may be closer to what you need. To get the most accurate measurement of the hole in your grease cap, I recommend using dial calipers. With the most accurate measurement I...
view full answer... - Recommended 2.441" EZ Lube Grease Cap With 1.18" OpeningIt sounds like you are looking for the 2.44" OD EZ Lube Grease Cap # 21-42-1 which will fit your 62mm (2.441") hub and has a 1.18" (29.97mm) opening for EZ lube bearings. You will also need Grease Cap Plug # RG04-010 to plug the holes to keep dirt and other debris from getting in the hub. I included a video for both of the products mentioned for you to take a look at.
view full answer... - Recommended Grease Cap Plug For EZ Lube Drive-In Grease CapThe rubber grease cap plug you need for the # 21-41-1 grease caps is part # RG04-010. These plugs work for grease caps that have a 1.18 inch dust cap hole.
view full answer... - How to Measure a Trailer Hub for the Correct Size Grease CapYou would need to measure the inside diameter of the hub opening to determine which cap size is needed. You would want to choose a cap whose outside diameter matches the inside diameter of the hub. Some of the most common sizes are 1.980 inch, 1.986 inch, 2.441 inch and 2.717 inch. As you can see the sizes can differ by very small amounts. To measure accurately you may want to get a dial caliper so that you can be confident you are getting the correct size for your hub. I have included...
view full answer... - Zerk Fittings Keep Falling Out on Boat Trailer With EZ-Lube SpindlesBecause the zerk fitting is a press fit, if they are falling out I would recommend simply leaving them out and replacing your existing grease caps with bearing protectors like Bearing Buddies. The Bearing Buddies you need will depend on your hub bore, or the outer bearing number. Once the fittings start falling out, there is not much that can be done to keep them in place. The holes where the zerk fitting was and the holes in the spindle that the grease passed through will not cause any...
view full answer... - Recommendation for Grease Cap Plugs for a Q5 Tahoe Boat TrailerWe do have a set of grease caps that are 1-1/4 inch. Check out the Grease Cap Plug for E-Z Lube Grease Caps, # RG04-010. These caps will fit much more snug than the 1.18 inch ones you currently have.
view full answer... - Replacement Grease Cap Plugs For Easy Grease Trailer Idler Hub Assembly # AKIHUB-545-35-EZ-KYes, the Grease Cap Plug # RG04-010 will fit the Grease Cap # DC200L-DCRP included with the Easy Grease Trailer Idler Hub Assembly # AKIHUB-545-35-EZ-K.
view full answer... - Availability of Replacement E-Z Lube Grease Cap and Plug for Trailer HubsIt sounds like you are needing a replacement grease cap and rubber plug for the Dexter hubs on your E-Z Lube axle. In order to find the correct part for your current hubs, you will simply want to take a quick measurement on your existing grease cap or the hub's bore. If you can tell me what model hub you have on the trailer, I should also be able to recommend the correct replacement cap to use. For example, the Replacement EZ Lube Drive-In Grease Cap # 21-41-1 features an outer diameter...
view full answer... - Difference Between the Rubber Lube Plugs # DC-RP and # RG04-010 The # RG04-010 includes a quantity of two caps, whereas the # DC-RP only includes one. It's the same cap though for either part number.
view full answer... - EZ Lube Spindle Grease Cap Plug RecommendationSounds like you are looking for the part # RG04-010 that you mentioned. This is the standard EZ lube grease cap plug that fits holes that are 1.18 inches in diameter.
view full answer... - Rubber Plug Recommendation for the Grease Cap # 21-41-1The rubber cap needed to use with the # 21-41-1 is the part # RG04-010. It does not come with the cap.
view full answer... - Would the TruRyde Grease Cap Plug # RG04-010 work as a Replacement for AL-KO Cap # 568067I did some checking and it looks like the Al-KO cap # 568067 is designed to fit a 1-3/16 inch hole. The Grease Cap Plug # RG04-010 is also designed to fit this size hole so it should work well for you.
view full answer... - What is the Size of the Rubber Plug in the End of the Dexter EZ Lube Grease CapsThe Grease Cap Plug for the E-Z Lube Grease Caps, # RG04-010, has a measurement of 1.18 inches. I checked a few other references and could not find any measurement other than the 1.18 inches for the size of the rubber plugs.
view full answer... - How Does an EZ-Lube Axle WorkOn an EZ-Lube axle, the grease gets inserted at the end of the spindle through a zerk fitting and comes out of a hole that should be in between the bearings, filling them both. You would not be able to use Bearing Buddies because the zerk fitting at the end of an EZ Lube axle would interfere with the installation.
view full answer... - Replacement Grease Cap For Nationwide Pontoon TrailerI can absolutely help you with this part. It sounds like for the deep dish, you may be looking for an EZ Lube Drive-In Grease Cap, that is # 21-41-1. There are grease cap plugs for the EZ Lube # RG04-010. I reached out to Nationwide Pontoon Trailer and they let me know the size needed and these are a fit for your trailer. If you prefer the rounded metal style, your replacement bearing cover is Grease Cap # RG04-020.
view full answer... - Will Grease Cap Plugs RG04-010 Fit RG04-040 Grease CapsYes, the # RG04-010 grease cap plugs are a great fit for the 1.986 inch outer diameter # RG04-040 grease caps.
view full answer... - Lug Nuts that Can Fit on Wheel Studs 7-262Yes the lug nuts you mentioned part # 12CLN-L are a fit to the wheel studs part # 7-262. The Lynx trailer wheel part # LHSL311 has a 4.25 inch pilot diameter so the wheel center cap part # 425EZ would fit. The EZ lube grease cap part # RG04-010 is a standard size grease cap plug for EZ lube spindles so it should work fine as well.
view full answer... - Replacement Grease Cap Plugs For Super Lube Axles On a 2003 Trailstar Boat TrailerThe Grease Cap Plug # DC-RP used on axles is generally one common size. This plug is designed to fit a grease cap with a 1.18" diameter opening. We also have them available as a Set # RG04-010 for one axle.
view full answer... - Grease Cap Recommendation to Replace Cap with Lost PlugWe do not have any grease cap plugs that are designed to fit a 1-1/2 inch opening. The only recommendation I could give you would be to get a new grease cap. To pick out the correct grease cap you will need to remove your current one and measure the distance of the opening on your hub with a dial caliper or micrometer. I attached a page that has all of the EZ lube grease caps we offer that have plugs in them.
view full answer... - Are Different Sizes For The E-Z Lube Grease Cap Plug Available? The 1.18" width on the Grease Cap Plug for E-Z Lube Grease Caps # RG04-010 is the only size that is offered.
view full answer...
- Availability of Replacement Rubber Plugs for # DC200L-DCRP EZ Lube Grease CapYou sure can, they're sold in pairs as part # RG04-010 or individually as part # DC-RP.
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Installed by:
Joe V
Installed by:
Steven C
Installed by:
Randy B
Installed by:
Ryan G
Expert Research:
Mike L
Expert Research:
Sarah L
Expert Research:
Robert G
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Jeffrey L
Video by:
Joshua S
Video by:
Alan C
Video by:
Zach D
Video Edited:
Jacob T
Video Edited:
Dustin K
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Jim C.
6/30/2015
Same as described above.