Are Different Sizes For The E-Z Lube Grease Cap Plug Available?

Question

Question:

Is there only size for the ez cap plugs?

asked by: Patrick G

0

Expert Reply:

The 1.18" width on the Grease Cap Plug for E-Z Lube Grease Caps # RG04-010 is the only size that is offered.

expert reply by: Bryce D

0

E-Z Lube Grease Cap Width
(click to enlarge)

Answer 1

To measure the width of a trailer wheel you will measure from where the tire beads will seat on the wheel. That will be from the inside of the inner wheel flange to the inside of the outer wheel flange, not from edge to edge of the wheel. To…

view full answer...

Answer 2

You would need to measure the inside diameter of the hub opening to determine which cap size is needed. You would want to choose a cap whose outside diameter matches the inside diameter of the hub. Some of the most common sizes are 1.980 inch,…

view full answer...

Answer 3

EZ Lube Dust Caps, like #DC200L-DCRP, have a rubber plug that can be removed to access the zerk fitting. The rubber plug can be removed by gently prying it up with a flathead screwdriver. If your dust cap is in good condition and you want to avoid…

view full answer...

Answer 4

If you are looking for a grease cap PLUG with the TRP stamped on it chances are the Grease Cap Plug for E-Z Lube Grease Caps #RG04-010 would work for you, but to be certain you will want to measure the diameter of the grease cap hole. If it is 1.18…

view full answer...

Answer 5

Yes,the RG04-010 Grease cap plugs fit the Dexter E-Z Lube grease caps on the Dexter E-Z Lube axles.

view full answer...

Answer 6

Sounds like you have EZ lube spindles and a cap that has a rubber plug that allows access to them. Can you get me the diameter of the opening you have so that I can pick out the correct cap? For example, we have the part #RG04-010 which is designed…

view full answer...

Answer 7

The Grease Cap Plug for the E-Z Lube Grease Caps, #RG04-010, has a measurement of 1.18 inches. I checked a few other references and could not find any measurement other than the 1.18 inches for the size of the rubber plugs.

view full answer...

Answer 8

You will want to use a dial caliper or micrometer like part #PTW80157 to measure the inner diameter of the hub you have on your trailer to determine what size cap would be needed. Check out the picture I attached that shows this measurement being…

view full answer...

Answer 9

The Rubber Lube Plug - Fits 1.18" Lubed Dust Cap #DC-RP is the replacement for the #RG04-040 grease cap as well as larger caps like the 2.44" OD Drive In Grease Cap with Plug #RG04-080. The Grease Cap Plug fro E-Z Lube Grease Caps is the…

view full answer...

Answer 10

The Grease Cap Plug for E-Z Lube Grease Caps - Qty 2 #RG04-010 is designed to fit in E-Z Lube axle caps that have a 1.18" diameter opening. If you don't have an E-Z Lube it's possible that if you're measuring the outside dimensions…

view full answer...

Answer 11

I'm assuming you're speaking of a grease cap that's driven into the hub bore. Grease caps are available in different sizes. There are two good ways to determine which size you need. One is to locate the reference number off of the outer…

view full answer...

Answer 12

The Grease Cap - 1.988" Outer Diameter part #F001518 is correct for a Dexter 10" Hub for 3,500 Axle.

view full answer...

Are Different Sizes For The E-Z Lube Grease Cap Plug Available?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching