Wheel Stud Replacement for 5200 lb Trailer Axle

Question

Question:

Hello, Looking for a wheel stud from a 12inch x 2inch electric drum brake, 8x6.5inch pattern, 5200 pound axle. 1/2-20 thread, 2.8inch long 2.5inch would work, 0.56inch spline diameter, 0.68inch spline length, stamped U 144inch on head Thanks

asked by: Lee T

0

Expert Reply:

Based on the dimensions you said you needed the Wheel Stud # 165995 would be exactly what you'd need.

expert reply by: Jameson C

0

Answer 1

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 2

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 5

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 6

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 7

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

Surge brakes use a hydraulic actuator to push fluid to the cylinder piston to activate the brake shoes on drum brakes or brake pads on disc brakes. This pressure should only be applied when weight is pushing against the hitch ball, so no pressure…

view full answer...

Answer 10

The Blue Ox systems cannot be moved back that far but we do have the perfect system for you. Take a look at the Reese SC weight distribution systems linked to the right (minus the ones that say Light Duty). These systems have narrow brackets that can…

view full answer...

Answer 11

For your Atwood water heater number gc6aa-10e, it sounds like you have either a wiring issue or an element issue. To determine if a replacement is needed you will want to make sure the connections are good to and from your switch. I recommend using a…

view full answer...

Answer 12

I added a photo which shows the location of the heating element of the Atwood Water Heater GC6AA-10E for you. It is item number 17 in the diagram. Atwood does recommend having a professional do the job if you are replacing it due to its location.

view full answer...

Wheel Stud Replacement for 5200 lb Trailer Axle

Product Page this Question was Asked From

Continue Researching