Customers compare STL59RB to these similar products
Products Featured in this Video
Today we're going to be taking a look at the Optronics thin line LED trailer light. This trailer tail light is going to serve 3 functions, such as your stop light, tail light, and turn signal light. It features a sonically sealed design so the housing and lens unit is completely waterproof so it is submersible. The thin line series also has a really nice low profile design so that way the light… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
We have a few different round tube mount couplers that might work for you. If the tube has a 1-3/4 inch diameter we have 4 options: #BD028381 is rated for 7,000 pounds and fits a 2 inch ball #BD028242 is rated for 5,000 pounds and fits a 2 inch…
view full answer...You definitely could use the Thinline LED Trailer Tail Light #STL59RB as a standard trailer stop/turn/running light on the sides of your trailer as all of those functions are supported on this light. If you check out the picture I attached you can…
view full answer...There are a number of things you will need if you want to re-wire your boat trailer to use LED lights and you should start with Junction Box #3375601100 and 7-Way #HM20041. Keep in mind you will also need Ring Terminals #44-5310A and Loom Clamps…
view full answer...I pulled the Empire Faucets Hybrid RV Bar Faucet #EM46FR and found that the inlet shanks are indeed 4" apart center to center. I'll have the description update to reflect this measurement.
view full answer...I think you will be very happy with an upgrade in your lights to the LED Trailer Tail Light - 6 Function - Submersible - 18 Diodes - Rectangle - Red Lens - Passenger, #STL56RB and the #STL57RB for the driver side. You can ground the lights…
view full answer...The Putco Red Blade LED Tailgate Combination Light Bar part #P92010-60 which is the lightbar I recommend for your trailer has LED lights so the amp draw will be very minimal. The reason that this is important is because the total amp draw for each…
view full answer...Grease seal set #RG06-050 is what you will need. These are double lip seals, just like what you have (the spring indicates that) and the dimensions are all the same including the 1/2 inch width.
view full answer...In order to use a third brake light for both brake and running light signals, you would need to use a light with turn, brake, and running light capabilities such as the Thinline LED Trailer Tail Light part #STL59RB. As most trailers are a 3 wire…
view full answer...After you plug the 4-way in from your 2006 Ford E-350 to the Curt Trailer Connector Adapter #C57102 you will need to run the rest of the wires as follows: The white wire will need to be grounded to a clean metal surface. The blue wire will go to…
view full answer...When using an idler hub or a hub and drum with brakes on the Timbren Axle-Less Trailer Suspension System, part #ASR2000S02, the difference in the distance from the bracket to the front face of the hub as shown in the attached drawing would be the…
view full answer...I have attached a photo for you below which shows how both a vehicle side and trailer side trailer connector is typically wired. I say typically because this is not always exact and so long as the trailer and vehicle side both match it will not…
view full answer...The note you are referencing in regard to the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #118628 specifically says the relay is "needed" so it is required in order to activate the tow package on your 2018 Acura…
view full answer...