Inlet Shank Spacing For The Empire Faucets Hybrid RV Bar Faucet # EM46FR

Question

Question:

Empire Faucets Hybrid RV Bar Faucet - Dual Teacup Handle - Chrome Item # EM46FR The listed specs state that the inlet stems are 8inch apart on center. They LOOK *and I require the stems to be 4inch apart on center. If they are, indeed, 4inch apart, I would gladly purchase them. Please confirm *and correct the spec listing that they are 4inch apart, on center. Thank you.

asked by: Phillip B

0

Expert Reply:

I pulled the Empire Faucets Hybrid RV Bar Faucet # EM46FR and found that the inlet shanks are indeed 4" apart center to center. I'll have the description update to reflect this measurement.

expert reply by: Kevin C

0

EM46FR Inlet Shank Spacing
(click to enlarge)

Answer 1

There are a number of things you will need if you want to re-wire your boat trailer to use LED lights and you should start with Junction Box #3375601100 and 7-Way #HM20041. Keep in mind you will also need Ring Terminals #44-5310A and Loom Clamps…

view full answer...

Answer 2

I think you will be very happy with an upgrade in your lights to the LED Trailer Tail Light - 6 Function - Submersible - 18 Diodes - Rectangle - Red Lens - Passenger, #STL56RB and the #STL57RB for the driver side. You can ground the lights…

view full answer...

Answer 3

Roadmasters priority when it comes to their sway bars is top notch quality and the easiest install for the customer. This typically cuts the install time down enough that you end up saving money if you pay to have the bars installed or decide to do…

view full answer...

Answer 4

Yes, you can remove the rivets and use some self tapping screws to secure the #LCV000334398 and complete the installation. If you watch the video attached below starting at the 10 minute mark you will see where they used the #FA1131822 to finish…

view full answer...

Answer 5

We've asked JR Products in the past if the RV Hand Pump Water Faucet #37297025 that you referenced can be used with pressurized water and they said yes so this would work with city water.

view full answer...

Answer 6

When determining what rise/drop to use on a B&W Tow & Stow, it is important that your trailer connection is as level as possible. The first thing you need to do is measure the height of your hitch receiver from level ground to the top inner…

view full answer...

Answer 7

11 inches from the bolt hole centers to the wall of the RV is the standard dimension for installing a 2 bolt toilet like the Dometic part #DOM87FR. You might check again and see if you didn't measure from the bolt centers and instead did from the…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

On this page (typically below the product links) there is a helpful link section that will have the install instructions fo the Hopkins Breakaway kit part #20400 that you referenced. I also attached an install video that shows the kit installed as…

view full answer...

Inlet Shank Spacing For The Empire Faucets Hybrid RV Bar Faucet # EM46FR

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching