Customers compare EQ90-02-9100 to these similar products
Products Featured in this Video
Today we're gonna take a look at the replacement bolts and hardware for the Equalizer Weight Distribution Head. Now this replacement hardware fits the Equalizer Weight Distribution Heads that are rated for 6,000-pound to 14,000-pound gross towing weight capacity. This will secure the head of some weight to the adjustable shank. The adjustable shank we do sell separately and it also has the space… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
To install the etrailer Trailer Hitch Receiver #e73ZR on your 2019 Jeep Cherokee Trailhawk you will need the following tools. Torque Wrench #ALL944001 capable of 139lb-ft torque Ratchet Set #PT64VR with 13mm, 15mm, 21mm, and 3/4" sockets,…
view full answer...If the trailer is less than 1 inch off of being perfectly level either up or down then it will be perfectly fine. Having it slightly higher would be better because presumably the tongue weight of the trailer will pull it down a little. You could also…
view full answer...For the head of Equalizer systems the torque rating is tighten the angle set bolt until it comes into contact with the shank and lifts the head to where the spacer rivet also comes into solid contact with the shank. Tighten the angle set bolt an…
view full answer...I attached a picture that shows the proper position of shackles and equalizers on trailer suspension. Sometimes the shackle will flip up but if you jack up the trailer by the axle that's got the shackle flipped you can usually get it to flip back…
view full answer...The sleeve adapters used adapt a 2-1/2 inch hitch to fit a 2 inch hitch accessory do not diminish the towing capacity of the hitch or the accessory installed in the hitch. We have the Curt hitch reducer part #C45405 that would work well for your…
view full answer...I'm not sure how to find out the age of your setup, but when I passed your photos along to my contact at Equal-i-zer he said that all you need to do for the upgraded system is swap out your 12K head unit for the 14K #EQ90-02-1400. Since your…
view full answer...For the Demco A-Frame Coupler #12660-97SP that you referenced the etrailer locking hitch pin part #e98888 would fit and work great. This has a usable span of 3-3/8 inches.
view full answer...If the front part of your square-bodied coupler is approximately 3 inches tall, based on the inner dimensions of the lock the Blaylock EZ Lock Trailer Coupler Lock #BLTL-33 will work well for you. The #BLTL-33 has inner dimensions of 3-1/8 inches x…
view full answer...The clip that goes around 3 of the leaves of the 5-Leaf Spring part #e34SR that you referenced can go either in front of the axle or behind it. Either way would be perfectly fine. I attached an FAQ on trailer suspension for you to check out as well.
view full answer...I reached out to my contact at Equal-i-zer (and Fastway) and he said you can continue using the existing Fastway e2 lift brackets on your trailer with the new Equal-i-zer 1,200 pound Spring Bars #EQ90-01-1299 and Head #EQ90-02-1200. This is not an…
view full answer...I would discourage the use of an adapter for use of 2 inch accessories in 1-1/4 inch trailer hitch receivers. The reason is that the adapter places the carrier farther away from the rear of the vehicle and hitch, creating additional torque that 1-1/4…
view full answer...That's a very well thought-out question and the correct system will be the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 12,000 lbs GTW, 1,200 lbs TW #EQ37120ET because the ideal system is one in which your total tongue weight…
view full answer...